Robustel GoRugged R3000 Lite User manual

-1-
Installation and Configuration Quick Guide
R3000 Quad
Industrial Cellular VPN Router with 4 Ethernet Ports
(4 Eth + 1 RS-232/1 RS-485 + 1 USB Host)
Environmental Requirements
Power input: 9~60V DC
Power consumption: 100 mA@12 V in idle state, 400 mA (peak) @12 V in communication state
Operating temperature: -40~75 °C
Relative humidity: 5~95% RH
Package Contents
Optional Accessories (sold separately)
3G/4G SMA cellular antenna (stubby/magnet optional)
Wall mounting kit
35 mm DIN rail mounting kit
Ethernet cable
AC/DC power adapter (12V DC, 1.5 A; EU/US/UK/AU plug optional)
Before installing your R3000 Quad Router, please verify the kit contents as
following.
1 x Robustel GoRugged R3000 Quad Industrial Dual SIM Cellular VPN
Router with 4 Ethernet Ports
1 x 3-pin pluggable terminal block with lock for power supply
1 x 7-pin pluggable terminal block with lock for serial and console port
1 x Quick Start Guide with download link of other documents or tools
*If any of the above items is missing or damaged, please contact your Robustel sales representative.

-2-
Hardware Introduction
1.
Overview
2.
Dimensions
PIN
Polarity
8
Positive
9
Negative
10
GND
PIN
Debug
RS-232
RS-485
Direction
1
CR
--
--
Router Device
2
CT
--
--
Router Device
3
GND
GND
GND
--
4
--
TXD
Data+(A)
Router Device
5
--
RXD
Data+(B)
Router Device
6
--
RTS
--
Router Device
7
--
CTS
--
Router Device
PIN
Function
1
TX+
2
TX-
3
RX+
6
RX-
3. Pinouts

-3-
4. LED Indicators
Name
Color
Status
Description
RUN
Green
On, fast blinking
(250 mSec blink time)
Router is powered on
(System is initializing)
On, blinking
(500 mSec blink time)
Router starts operating
Off
Router is powered off
PPP
Green
On, solid
Link connection is working
Off
Link connection is not working
USR-
OpenVPN
Green
On, solid
OpenVPN connection is
established
Off
OpenVPN connection is not
established
USR-IPsec
Green
On, solid
IPsec connection is established
Off
IPsec connection is not
established
USR-WiFi
Green
On, solid
WiFi is enabled and working
properly
Off
WiFi is disabled or not working
properly
Green
On, solid
High Signal strength (21-31) is
available
Yellow
On, solid
Medium Signal strength (11-20)
is available
Red
On, solid
Low Signal strength (1-10) is
available
/
Off
No signal
Name
Color
Status
Description
NET
Green
On, solid
Connection to 4G network is
established
Yellow
On, solid
Connection to 3G network is
established
Red
On, solid
Connection to 2G network is
established
/
Off
Connection to network is not
established or establishing
SIM
Green
On, blinking
Backup card is being used
Off
Main card is being used
5. USB Interface
Function
Operation
Firmware upgrade
USB interface is used for batch firmware upgrading, but
cannot be used for sending or receiving data from slave
devices which connected to it. You can insert a USB
storage device into the router’s USB interface, such as a
U disk or a hard disk. If there have a supported
configuration file or a router firmware in this USB
storage device, the router will automatically update the
configuration file or the firmware.

-4-
6. Reset Button
Function
Operation
Reboot
Press and hold the RST button for 5 seconds under the
operating status.
Restore to factory
default settings
Wait for 5 seconds after powering up the router, press
and hold the RST button until all six LEDs start blinking
one by one, and release the button to return the router
to factory defaults.
7. Ethernet Port
R3000 Quad Router has four Ethernet port with two LED indicators. The
yellow one is link indicator and the green one is speed indicator. For details
about status, see the table below.
Indicator
State
Description
Link indicator
On, solid
Connection is established
On, blinking
Data is being transferred
Off
Connection is not established
Speed indicator
On, solid
100 Mbps mode
Off
10 Mbps mode

-5-
3. Do not forget to twist the cover tightly to avoid being stolen.
4. Do not touch the metal of the card surface in case information in the
card will lost or be destroyed.
5. Do not bend or scratch the card.
6. Keep the card away from electricity and magnetism.
7. Make sure router is powered off before inserting or removing the card.
2. Attach External Antenna (SMA Type)
Attach the SMA external antenna to the router’s connector and twist tightly.
Make sure the antenna is within the correct frequency range provided by
the operator and with 50 Ohm impedance.
Note: Recommended torque for mounting is 0.35 N.m.
3. Connect the Router to a Computer
Connect an Ethernet cable to any port marked ETH0~ETH3 at the bottom of
the router, and connect the other end of the cable to your computer.
Hardware Installation
Insert SIM card/Micro SD card
1. Make sure router is powered off.
2. To remove cover, loosen the screws
associated with the cover by using a
screwdriver and then find the SIM card
slot/Micro SD card slot.
3. To insert SIM card/Micro SD card, press the
card with finger until your hear a click and
then tighten the screws associated with the
cover by using a screwdriver.
4. To put back the cover and tighten the
screws associated with the cove by using a
screwdriver.

Remove SIM card/Micro SD card
1. Make sure router is powered off.
2. To remove slot cover, loosen the screws associated with the cover by
using a screwdriver and then find the SIM card slot/Micro SD card slot.
3. To remove SIM card/Micro SD card, press the card with finger until it
pops out and then take out the card.
4. To put back the cover and tighten the screws associated with the cover
by using a screwdriver.
Note:
1. Recommended torque for inserting is 1.0 N.m, and the maximum
allowed is 1.2 N.m.
2. Use the specific card when the device is working in extreme
temperature (temperature exceeding 40℃), because the regular card
for long-time working in harsh environment will be disconnected
frequently.
1. Insert or Remove SIM Card/Micro SD Card

-6-
4. Mount the Router
The router can be placed on a desktop or mounted to a wall or a 35 mm DIN
rail.
Two methods for mounting the router
Wall mounting (measured in mm)
Use 3 pcs of M3*4 flat head Phillips screws to fix the wall mounting kit
to the router , and then use 2 pcs of M3 drywall screws to mount the
router associated with the wall mounting kit on the wall.
Note: Recommended torque for mounting is 1.0 N.m, and the
maximum allowed is 1.2 N.m.
DIN rail mounting (measured in mm)
Use 3 pcs of M3*6 flat head Phillips screws to fix theDIN rail to the
router, and then hang the DIN rail on the mounting bracket. It is
necessary to choose a standard bracket.
Note: Recommended torque for mounting is 1.0 N.m, and the
maximum allowed is 1.2 N.m.
5. Power Supply
R3000 Quad router supports reverse polarity protection, but always refers
to the figure above to connect the power adapter correctly. There are two
cables associated with the power adapter. Following to the color of the
head, connect the cable marked red to the positive pole through a terminal
block, and connect the yellow one to the negative in the same way.
Note: The range of power voltage is 9 to 60V DC.

-7-
PC Configuration
There are two methods to get IP address for the PC, one is to obtain an IP address automatically from “Local Area Connection”, and another is to configure a
static IP address manually within the same subnet of the router. Please refer to the steps below.
Here take Windows 7 as example, and the configuration for windows system is similar.
2. Click Properties in the window of
Local Area Connection Status.
1. Click Start > Control panel, double-click Network
and Sharing Center, and then double-click Local
Area Connection.
3. Choose Internet Protocol Version
4 (TCP/IPv4)and click Properties.
4. Two ways for configuring the IP address of PC.
Obtain an IP address automatically:
Use the following IP address
(Configured a static IP address manually within the
same subnet of the router)
5. Click OK to finish the configuration.

-8-
Router Configuration
1.
Log in the Router
To log in to the management page and view the configuration status of
your router, please follow the steps below.
1.
On the PC, open a web browser such as Internet Explorer, Google and
Firefox etc.
2. From your web browser, type the IP address of the router into the
address bar and press enter. The default IP address of the router is
192.168.0.1, though the actual address may vary.
3. In the login page, enter the username and password, choose language
and then click LOGIN. The default username and password are
“admin”.
Note: If enter the wrong username or password over six times, the
login web will be locked for 5 minutes.
4. After logging in, the home page of the R3000 Quad Router’s web
interface is displayed, for example.
Note: To configure parameters should follow this order “modify
parameter 1 > Submit > modify parameter 2 > Submit > Save & Apply”.
2. Configure the Cellular Connection
Click Interface > Link Manager > Link Manager > General Settings,
choose “WWAN1”as the primary link and “WWAN2”as the backup
link, and set “Cold Backup”as the backup mode, then click “Submit”.
Note: Link Settings allows you to configure the parameters of link
connection, including WWAN1/WWAN2, WAN and WLAN. It is
recommended to enable Ping detection to keep the router always
online. The Ping detection increases the reliability and also costs the
data traffic.

-9-
When finished, click Submit > Save & Apply for the configuration to
take effect.
3. Check the Cellular Connection Status
Click Interface > Cellular > Status to view the status of the cellular
connection, and click the row of status, the details status information
will be displayed under the row.
Click on the right-most of WWAN1 to enter the configuration window.
The window is displayed as below when enabling the “Automatic APN
Selection”option.
The window is displayed as below when enabling the “Ping Detection”
option.

-10-
4. Configure the IP of Router
There are four Ethernet ports on R3000 Quad Router, including
ETH0~ETH3. The ETH0 on the router can be configured as either a
WAN or a LAN port, while ETH1~ETH3 can only be configured as LAN
ports. The ETH0~ETH3 can freely choose from lan0~lan3, but at least
one LAN port must be assigned as lan0. The default settings of
ETH0~ETH3 are lan0 and their default IP are
192.168.0.1/255.255.255.0.
Configure Lan0
Click Interface > LAN > LAN, click lan0’s edit button to configure its
configuration, and modify its IPv4 address and Netmask.
Click lan0’s edit button and configure its parameters in the pop up
window.
When finished, click Submit > Save & Apply for the configuration to
take effect.
Configure Lan1
Click Interface > Ethernet > Ports, click eth1’s edit button, choose
“lan1”as the assigned port, and click “Submit”.
Note: By default, there is a LAN port (lan0) in the list. To begin adding a
new LAN port (lan1), please configure one of eth0~eth3 as lan1 first in
Ethernet > Ports > Port Settings. Otherwise, the operation will be
prompted as “List is full”.
Click Interface > LAN in the homepage, and click the add button.

-11-
Choose lan1 as the interface, and configure its IPv4 address and
Netmask.
When finished, click Submit > Save & Apply for the configuration to
take effect.
Configure Multiple IP
Click Interface > LAN > Multiple IP, and click the edit button of lan0.
Note: You may click to edit the multiple IP of the LAN port, or click
to delete the multiple IP of the LAN port. Now, click to add a
multiple IP to the LAN port.
When finished, click Submit > Save & Apply for the configuration to
take effect.
Configure WAN
Click Interface > Ethernet > Ports, click the edit button of eth0, choose
“wan”as the port assignment, and click “Submit”;
Click Interface > Link Manager > General Settings, choose “WAN”as
the primary link, and choose “None”as the backup link.
Click the edit button of WAN to enter its configuration window.

-12-
Configure WAN’s related parameters as below.
The window is displayed as below when enabling the “Ping Detection”
option.
When finished, click Submit > Save & Apply for the configuration to
take effect.
Guangzhou Robustel Technologies Co., Ltd.
Add: 3rd Floor, Building F, Kehui Park, No.95 Daguan Road, Guangzhou, China 510660
Tel: [phone]
Email:
[e-mail]
Web: www.robustel.com