Rockler 52149 User manual

Rail Coping Sled
Instructions

2
>For any tool used in conjunction with this product,
always read, understand and follow the instructions
 andsafetywarningsintheowner’smanualforthattool.
 Ifyoudonothavetheowner’smanual,obtainone
 fromthetool’smanufacturerbeforeusingitwith
 thisproduct.
>Before using this product, review and verify that all
 toolstobeusedwithithavesafetyequipment
installed and are in proper working order as
 definedbythetools’owner’smanuals.
>Do not use this product until you have read and
are confident you understand the:
 • Assembly(pp4);
 • SetupandUse(pp.4).
>Remainalertandusegoodjudgmentwhenusing
 thistool.Donotusethistoolifyouareinanyway
 impairedbymedications,alcohol,drugsorfatigue.
> Dressappropriatelyandremovealljewelry,secure
 looseclothingandtieuplonghairbeforeusing
 thistool.
> Itisthesoleresponsibilityofthepurchaserofthistool
 toensurethatanythirdpartywhomyouallowtouse
 thisproductreadsandcomplieswithalltheinstructions
 andsafetyprecautionsoutlinedinthismanualprior
 touse.
>Maintain these instructions and warnings as long as
 youownthetool.Keepthisbookletinaplacewhere
 itwillbereadilyavailableforreference.
>Theuserassumesallriskandresponsibilityforthe
proper use of this tool and for ensuring product
 suitabilityforintendedapplication.
>AlwayswearsafetyglassesincompliancewithANSI
safety standards and hearing protection and follow all
standard shop safety practices, including:
• Keepyourworkareawelllitandclean;
• Unplugallpowertoolsbeforemakingany
  adjustmentsorchangingaccessories;
• Usedustcollectiontoolsanddustfacemasksto
  reduceexposuretodust;
• Useaccessorysafetyequipmentsuchas
  featherboards,pushsticksandpushblocks
  wheneverappropriate;
•Do not use power tools in explosive
  environments(e.g.,inthepresenceof
  flammableliquids,fumesordust);
• Keepchildrenandbystandersawayfrom
  thetooloperatingarea;
• Maintainproperfootingatalltimesand
  donotoverreach;
• Donotforcethetool.
>These warnings and instructions do not represent the
 totalofallinformationavailableregardingtoolsafety,
 useandtechnique.Pleasereadthefullmanualbefore
using this product and always seek out opportunities to
 learnmoreandimproveyourskillsandknowledge.
   Drilling,sawing,sandingormachining
woodproductscanexposeyoutowooddust,asubstance
knownottheStateofCaliforniatocausecancer.
Avoidinhalingwooddustoruseadustmaskorother
safeguardsforpersonalprotection.Formoreinformation
gotowww.P65Warnings.ca.gov/wood.
Thistoolisdesignedforspecificapplicationsasdefinedintheinstructionsandshouldnotbemodifiedand/orused
foranyotherapplications.BeforeusingtheRailCopingSled,read,understandandfollowallinstructionsandsafety
informationprovided.KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
GENERAL SAFETY WARNINGS

3
Quantity
1Fence Guide 1
2 Sled Base 1
3 Fixed Fence 1
4 AdjustableFence 1
5 LeverClamp 1
6 SacrificialPiece 1
7 Front Handle 1
8 Rear Handle 1
9 1"RoundKnob 2
10 4-StarKnob 1
PARTS LIST - RAIL COPING SLED Quantity
11 LargeWasher 2
12 SmallWasher 4
13 Spacer 2
14 5/16"-18TPIx1"T-SlotBolt 1
15 5/16"-18TPIx11⁄2"T-SlotBolt 1
16 5/16"-18TPIx21⁄2"T-SlotBolt 3
17 CapNut 4
18 13⁄4"MountingScrews 4
19 #8x13⁄4"WoodScrews 2
20 AbrasiveStrip 1
15
18
16
14
16
2
10 6
3
19
8
17
13
11
9
12
5
4
1
7
20

4
Assembly
1. Assemble the parts as shown. Do not fully tighten the
1" Round Knobs (9) that secure the Fence Guide (1),
the Front and Rear Handles (7 and 8) or the Mounting
Screws (18) that attach the Fixed Fence (3) and Lever
Clamp (5) to the Sled Base (2). You will tighten these
during calibration. Do not attach the Sacrificial Piece (6)
until all setup and calibration steps are completed.
Setup and Use
1. Position the assembled Rail Coping Sled so that the
clear Fence Guide (1) is tight against the fence of the
router table. Make sure the 1"Round Knobs (9) on the
Fence Guide are loose.
2. Keeping the Fence Guide (1) against the fence, adjust
the Sled Base (2) until it is precisely 3/4"away from
fence along its entire length. Take measurements at
Fig. 1
1
9
Fig. 2
3
8

5
both ends of the Sled Base to confirm that it is parallel
to the router table fence. Fully tighten the 1"Round
Knobs (9), then measure again to confirm that
nothing shifted. Fig. 1.
3. With the Fence Guide (1) still tight against the router
table fence, use a combination or engineer’s square to
set the sled’s Fixed Fence (3) at precisely 90°. Tighten
the Rear Handle (8) to lock the Fixed Fence in place,
then flip the Sled Base (2) and tighten the Mounting
Screws (18). If needed, use a 5/16"or 8mm wrench to
hold the Cap Nuts (17) while tightening. Fig. 2.
4. To set the bit height, place a test piece of your rail
stock on the Sled Base (2), slide it next to the bit and
adjust the bit until it’s at about the proper height.
Tighten the bit. Fig. 3 - Wooden Block Method.
Note: To make precise setup faster and easier when
using Rockler rail and stile bit sets on 3/4”stock,
we offer dedicated setup jigs (Fig. 3 - Setup Jig
Method) that have the rail and stile profiles machined
into the edges. Go to www.rockler.com for details.
5. Align the router table fence flush with the the bit’s
bearing and secure it in place.
6. Position the test stock for routing by pressing it up
against the Fixed Fence (3) and the router table fence.
Fig. 3
Wooden
Block
Method
Setup Jig
Method
2

6
7. Slide the Adjustable Fence (4) tight against the stock
and tighten the 4-Star Knob (10). Fig. 4 - Arrow 1.
8. Use the knob on the Lever Clamp (5) to adjust the clamp
foot so it will apply sufficient pressure, then engage the
clamp to fully secure the stock. Fig. 4 - Arrow 2.
9. Make a test cut. Fine-tune the bit height and repeat test
cuts until the joint is flush.
10. Return the sled to the router table, with the Fence
Guide (1) up against the fence. Place the Sacrificial
Piece (6), square corners down, on the Sled Base (2)
up against the Fixed Fence (3) and slide it toward the
router table fence until it makes contact. Secure it by
driving #8 x 13⁄4”Screws (19) through the predrilled
holes in the back edge of the Fixed Fence. Use a
combination or engineer’s square to verify that it’s
square to the router table fence. Fig. 5.
Fig. 4
Fig. 5
4
5
10
3
6

7
11. Clamp your project stock in the sled, up against the
Sacrificial Piece (6), and make your cuts, moving the
sled from right to left on the router table. Fig. 6.
Fig. 6
Check Rockler.com for updates. If you have further questions, please
contact our Technical Support Department at 1-800-260-9663
or [e-mail]
Notes

Distributed by Rockler Companies, Inc.
©2017 Rockler Woodworking and Hardware
52149
Rev 03/17