ROOMS TO GO KIDS CANYON LAKE Series User manual

WARNING DANGER
Failure to follow these warnings and assembly instructions could result in serious
injury or death. To help prevent serious or fatal injuries from entrapment or falls:
-
Read all instructions before assembling bunk bed and keep these instructions for future reference.
-
Before each usage or assembly, inspect bunk bed for damaged hardware, loose joints, missing
parts, or sharp edges. DO NOT Use bunk bed if any parts are missing or broken.
-
DO NOT Use substitute parts. Contact your local Rooms To Go or visit www.ROOMSTOGO.COM
for replacement parts and instructional literature if needed.
-
Follow the information on the warnings appearing on the upper bunk end structure and on the carton,
DO NOT REMOVE WARNING LABEL FROM BED.
-
Always use the recommended size mattress or mattress supports, or both to help prevent the likelihood
of entrapment or falls.
-Ensure thickness of mattress and foundation combine does not exceed
10 inches (255mm
) and
mattress surface is at least
5 inches (127mm)
below upper edge of guardrails.
-
Do not allow children under 6 years of age to use the upper bunk.
-
Periodically check and ensure that the guardrail, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
-
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
-
Limit top bunk use to one person.
-
Always use the ladder for entering and leaving the upper bunk.
-
Use of night light may provide added safety precaution for a child using the upper bunk.
-
Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed next to
the wall, the guardrail that runs the full length of the bed should be placed against the wall to
prevent entrapment between the bed and wall.
-
The use of water or sleep flotation mattress is prohibited.
-
This bunk bed meets all the requirements of ASTM 1427-19.
STRANGULATION HAZARD:
Never attach or hang items to any part of the bunk bed that are not designed for
use with the bed; for example, but not limited to, hooks, belts, and jump ropes.
CANYON LAKE COLLECTION
THANK YOU FOR YOUR PURCHASE
5/12/2022 Page 1 of 4

P A R T S L I S T
3983400P TWIN/TWIN DOUBLE STAIRS BUNK JAVA
RTG SKU # STYLE # ITEM DESCRIPTION
36034003 34C-160 STEP BUNK UNIT
38000232 100-645 TWIN SLAT PACK (4)
38000232 100-645 TWIN SLAT PACK (4)
36034003 34C-160 STEP BUNK UNIT
35734006 34C-730 4 SIDE RLS/2 GUARD RLS
34934009 34C-744 TRUNDLE BED OPTIONAL
36034015 34G-160 STEP BUNK UNIT
36034015 34G-160 STEP BUNK UNIT
3983401P TWIN/TWIN DOUBLE STAIRS BUNK ASH GRAY
RTG SKU # STYLE # ITEM DESCRIPTION
38000232 100-645 TWIN SLAT PACK (4)
34934011 34G-744 TRUNDLE BED OPTIONAL
35734018 34G-730 4 SIDE RLS/2 GUARD RLS
38000232 100-645 TWIN SLAT PACK (4)
14 Pcs
42 Pc
24 Pcs
5/16-18 x 50 mm Bolt
Side rails
PARTS LIST QTY PARTS LIST QTY HARDWARE LIST QTY
38 Pcs
Drywall screw
1 Pc
22 Pcs Step bunk unit 5 mm Hex key
51 Pc
5 mm Hex key (included)
Twin slats Trundle bed (Optional)
16 Pcs
TOOLS NEEDED
Guardrails 6 x 1 1/4" Phillips screwdriver (not included)
5/12/2022 Page 2 of 4
A
B
C

For stairs on the left, first remove the screw, then remove the panel
and install it on the other side and secure with the screw. Assemble bottom side rails.
ASSEMBLY INSTRUCTIONS
Install slats, one on each end, two equally spaced in the middle,
then fasten with 1 1/4" screws. Repeat step 2 & 3 for top set of side rails.
5/12/2022 Page 3 of 4
STEP 4
STEP 3
STEP 2
B
A
A
A
C
C
C
A
B
C
A
A
C
A
B
STEP 1
A

Twin size mattress- 74" - 75" long and 37-1/2" - 38-1/2" wide
Twin size Bunkie board- 74" long and 37-1/2" wide
Full size mattress- 74" - 75" long and 52-1/2" - 53-1/2" wide
Full size Bunkie board- 74" long and 52-1/2" wide
ASSEMBLY INSTRUCTIONS
Assemble guardrails and tighten all bolts. For optional Trundle bed follow assembly instructions inside
MAKE SURE ALL BOLTS ARE TIGHTENED COMPLETELY Trundle bed box, then slide under the bed as shown.
PLEASE CONTACT YOUR RETAIL STORE WITH SERVICE OR PARTS REPLACEMENT REQUEST
5/12/2022 Page 4 of 4
Place Bunkie boards (required, sold separately) on top of the slats
Use only correct mattress dimensions and Bunkie board:
STEP 7
STEP 5 A
B
A
A
STEP 6