ROOMS TO GO KIDS CREEKSIDE 2.0 3874440P User manual

WARNING DANGER
Failure to follow these warnings and assembly instructions could result in serious
injury or death. To help prevent serious or fatal injuries from entrapment or falls:
-
Read all instructions before assembling bunk bed and keep these instructions for future reference.
-
Before each usage or assembly, inspect bunk bed for damaged hardware, loose joints, missing
parts, or sharp edges. DO NOT Use bunk bed if any parts are missing or broken.
-
DO NOT Use substitute parts. Contact your local Rooms To Go or visit www.ROOMSTOGO.COM
for replacement parts and instructional literature if needed.
-
Follow the information on the warnings appearing on the upper bunk end structure and on the carton,
DO NOT REMOVE WARNING LABEL FROM BED.
-
Always use the recommended size mattress or mattress supports, or both to help prevent the likelihood
of entrapment or falls.
-Ensure thickness of mattress and foundation combine does not exceed
10 inches (255mm
) and
mattress surface is at least
5 inches (127mm)
below upper edge of guardrails.
-
Do not allow children under 6 years of age to use the upper bunk.
-
Periodically check and ensure that the guardrail, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
-
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
-
Limit top bunk use to one person.
-
Always use the ladder for entering and leaving the upper bunk.
-
Use of night light may provide added safety precaution for a child using the upper bunk.
-
Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed next to
the wall, the guardrail that runs the full length of the bed should be placed against the wall to
prevent entrapment between the bed and wall.
-
The use of water or sleep flotation mattress is prohibited.
-
This bunk bed meets all the requirements of ASTM 1427-19.
STRANGULATION HAZARD:
Never attach or hang items to any part of the bunk bed that are not designed for
use with the bed; for example, but not limited to, hooks, belts, and jump ropes.
CREEKSIDE 2.0 COLLECTION
THANK YOU FOR YOUR PURCHASE
11/7/2022 Page 1 of 63

11/7/2022 Page 46 of 63
Folding desk (Add on)
Full slats
54 Pc Loft Bookshelf
48 Pc
81 Pc
Guardrails 5 Drw Loft chest
3/8" x 3 1/8" Metal
pin
Allen wrench (included)
24 Pc Full bunkbed end 5 mm Hex key
8 Pcs
71 Pc
Side rails 6 x 1 1/4"
32 Pc
Drywall screw
2 Pcs
FOLDING DESK HARDWARE
2 Pcs
6 x 1 1/4"
Drywall screw
TOOLS NEEDED
11 Pc
61 Pc
16 Pcs
Phillips screwdriver (not included)
5/16"-18 x 3 3/8" Bolt
PARTS LIST QTY PARTS LIST QTY HARDWARE LIST QTY
Full top bunk bed end
1 Pc
36240416 40B-601 FOLDING DESK (Add on)
36340418 40B-760 LOFT BOOKSHELF
38300238 100-648 FULL/FULL SLAT PACK
3874441P FULL LOFT W/CHEST & BOOKCASE CHESTNUT
36740416 40B-732
4 PC RAILS(2 GUARD & 2 SIDE RAILS)
36040412 40B-711 LOFT CHEST
35640413 40B-704 1 PC BUNKBED END FULL
35940419 40B-703 FULL TOP BUNKBED END
P A R T S L I S T
3874440P FULL LOFT W/CHEST & BOOKCASE CHARCOAL
RTG SKU # STYLE # ITEM DESCRIPTION
35640401 40G-704 1 PC BUNKBED END FULL
38300238 100-648 FULL/FULL SLAT PACK
36040400 40G-711 LOFT CHEST
36340406 40G-760 LOFT BOOKSHELF
35940407 40G-703 FULL TOP BUNKBED END
36740404 40G-732
4 PC RAILS(2 GUARD & 2 SIDE RAILS)
36240404 40G-601 FOLDING DESK (Add on)
RTG SKU # STYLE # ITEM DESCRIPTION
A
B
C
D
C

CASES ON THE LEFT
CASES ON THE RIGHT
CASES ON THE RIGHT CASES ON THE LEFT
Assemble bookshelf and chest, using the fastening board and bolts previously removed, align both pieces and tight completely as shown.
11/7/2022 Page 47 of 63
FIRST DETERMINE THE CONFIGURATION THAT FITS YOUR ROOM
First choose which configuration fits your room ( left or right),
For Right remove center molding by lifting up then pulling out, then
ASSEMBLY INSTRUCTIONS
remove third drawer, for Left remove center molding and open the door. Remove fastening board and save for next step.
STEP 3
STEP 2 STEP 1 B
B
B

11/7/2022 Page 48 of 63
then fasten with 1 1/4" screws. MAKE SURE ALL BOLTS ARE TIGHTENED COMPLETELY
ASSEMBLY INSTRUCTIONS
Assemble loft chest, loft bookshelf and top bunk bed end. Assemble top side rails.
Install slats, one on each end, two equally spaced in the middle, Assemble guardrails and tighten all bolts.
STEP 5
STEP 6
STEP 4
B
STEP 7
A
A
A
A
D
D
D
D
B
A
B
A
A
A
A
A
C
C

Twin size mattress- 74" - 75" long and 37-1/2" - 38-1/2" wide
Twin size Bunkie board- 74" long and 37-1/2" wide
Full size mattress- 74" - 75" long and 52-1/2" - 53-1/2" wide
Full size Bunkie board- 74" long and 52-1/2" wide
11/7/2022 Page 49 of 63
Place Bunkie boards (required, sold separately) on top of the slats
Use only correct mattress dimensions and Bunkie board:
PLEASE CONTACT YOUR RETAIL STORE WITH SERVICE OR PARTS REPLACEMENT REQUEST
ASSEMBLY INSTRUCTIONS
STEP 8

Place folding desk by sliding into the opening of loft chest
then push down
11/7/2022 Page 50 of 63
Remove center molding by lifting up then pulling out Unfold desk leg and look for hardware pack inside desk box.
Secure each corner block with 1 1/4" screw
Unfold corner supports (from desk box hardware pack) in the pre-bore hole.
ASSEMBLY INSTRUCTIONS
STEP 9
STEP 11
STEP 10
STEP 12
STEP 13
C
C