ROOMS TO GO KIDS CREEKSIDE 2.0 3694040P User manual

WARNING DANGER
Failure to follow these warnings and assembly instructions could result in serious
injury or death. To help prevent serious or fatal injuries from entrapment or falls:
-
Read all instructions before assembling bunk bed and keep these instructions for future reference.
-
Before each usage or assembly, inspect bunk bed for damaged hardware, loose joints, missing
parts, or sharp edges. DO NOT Use bunk bed if any parts are missing or broken.
-
DO NOT Use substitute parts. Contact your local Rooms To Go or visit www.ROOMSTOGO.COM
for replacement parts and instructional literature if needed.
-
Follow the information on the warnings appearing on the upper bunk end structure and on the carton,
DO NOT REMOVE WARNING LABEL FROM BED.
-
Always use the recommended size mattress or mattress supports, or both to help prevent the likelihood
of entrapment or falls.
-Ensure thickness of mattress and foundation combine does not exceed
10 inches (255mm
) and
mattress surface is at least
5 inches (127mm)
below upper edge of guardrails.
-
Do not allow children under 6 years of age to use the upper bunk.
-
Periodically check and ensure that the guardrail, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
-
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
-
Limit top bunk use to one person.
-
Always use the ladder for entering and leaving the upper bunk.
-
Use of night light may provide added safety precaution for a child using the upper bunk.
-
Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed next to
the wall, the guardrail that runs the full length of the bed should be placed against the wall to
prevent entrapment between the bed and wall.
-
The use of water or sleep flotation mattress is prohibited.
-
This bunk bed meets all the requirements of ASTM 1427-19.
STRANGULATION HAZARD:
Never attach or hang items to any part of the bunk bed that are not designed for
use with the bed; for example, but not limited to, hooks, belts, and jump ropes.
CREEKSIDE 2.0 COLLECTION
THANK YOU FOR YOUR PURCHASE
11/7/2022 Page 1 of 63

35540409 40G-706 1 PC BUNKBED END TWIN
36740404 40G-732 4 PC RAILS(2 GUARD & 2 SIDE RAILS)
35540411
P A R T S L I S T
3694040P TWIN LOFT CHARCOAL
RTG SKU # STYLE # ITEM DESCRIPTION
35540409 40G-706 1 PC BUNKBED END TWIN
38000232 100-645 TWIN SLAT PACK (4)
40B-706 1 PC BUNKBED END TWIN
35540411 40B-706 1 PC BUNKBED END TWIN
3694041P TWIN LOFT CHESTNUT
RTG SKU # STYLE # ITEM DESCRIPTION
36740416 40B-732 4 PC RAILS(2 GUARD & 2 SIDE RAILS)
38000232 100-645 TWIN SLAT PACK (4)
12 Pcs
42 Pcs
16 Pcs
5/16"-18 x 3 3/8" Bolt
PARTS LIST QTY PARTS LIST QTY HARDWARE LIST QTY TOOLS NEEDED
Phillips screwdriver (not included)
5 mm Hex key (included)
34 Pcs
Drywall screw
Side rails
1 Pc
22 Pcs
1 pc bunkbed end twin
5 mm Hex key
Twin slats
8 Pcs
Guardrails 6 x 1 1/4"
11/7/2022 Page 5 of 63
A
B
C

Assemble side rails.
Install slats, one on each end, two equally spaced in the middle, Assemble guardrails and tighten all bolts.
then fasten with 1 1/4" screws. MAKE SURE ALL BOLTS ARE TIGHTENED COMPLETELY
ASSEMBLY INSTRUCTIONS
11/7/2022 Page 6 of 63
STEP 3
STEP 2
B
STEP 1
A
A
B
C
B
A
A
B
C
C
B
A
B
A
A
A
A
A
A
A

Twin size mattress- 74" - 75" long and 37-1/2" - 38-1/2" wide
Twin size Bunkie board- 74" long and 37-1/2" wide
Full size mattress- 74" - 75" long and 52-1/2" - 53-1/2" wide
Full size Bunkie board- 74" long and 52-1/2" wide
ASSEMBLY INSTRUCTIONS
PLEASE CONTACT YOUR RETAIL STORE WITH SERVICE OR PARTS REPLACEMENT REQUEST
11/7/2022 Page 7 of 63
Place Bunkie boards (required, sold separately) on top of the slats
Use only correct mattress dimensions and Bunkie board:
STEP 4