ROOMS TO GO KIDS CREEKSIDE 2.0 3964040P User manual

WARNING DANGER
Failure to follow these warnings and assembly instructions could result in serious
injury or death. To help prevent serious or fatal injuries from entrapment or falls:
-
Read all instructions before assembling bunk bed and keep these instructions for future reference.
-
Before each usage or assembly, inspect bunk bed for damaged hardware, loose joints, missing
parts, or sharp edges. DO NOT Use bunk bed if any parts are missing or broken.
-
DO NOT Use substitute parts. Contact your local Rooms To Go or visit www.ROOMSTOGO.COM
for replacement parts and instructional literature if needed.
-
Follow the information on the warnings appearing on the upper bunk end structure and on the carton,
DO NOT REMOVE WARNING LABEL FROM BED.
-
Always use the recommended size mattress or mattress supports, or both to help prevent the likelihood
of entrapment or falls.
-Ensure thickness of mattress and foundation combine does not exceed
10 inches (255mm
) and
mattress surface is at least
5 inches (127mm)
below upper edge of guardrails.
-
Do not allow children under 6 years of age to use the upper bunk.
-
Periodically check and ensure that the guardrail, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
-
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
-
Limit top bunk use to one person.
-
Always use the ladder for entering and leaving the upper bunk.
-
Use of night light may provide added safety precaution for a child using the upper bunk.
-
Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed next to
the wall, the guardrail that runs the full length of the bed should be placed against the wall to
prevent entrapment between the bed and wall.
-
The use of water or sleep flotation mattress is prohibited.
-
This bunk bed meets all the requirements of ASTM 1427-19.
STRANGULATION HAZARD:
Never attach or hang items to any part of the bunk bed that are not designed for
use with the bed; for example, but not limited to, hooks, belts, and jump ropes.
CREEKSIDE 2.0 COLLECTION
THANK YOU FOR YOUR PURCHASE
11/7/2022 Page 1 of 97

71 Pc
Full ext kit
Footboard
11/7/2022 Page 80 of 97
1 Pc 8 Pcs
Folding desk (Add on)
50 mm bolts
Headboard
12 1 Pc
2 Pcs
Metal plates
Twin slats
8 Pcs
61 Pc Cup nut
11
5 Drw Loft chest
3/8" x 3 1/8" Metal
pin
10 1 Pc
4 Pc
91 Pc
16 Pcs
6 x 1 1/4"
Drywall screw
2 Pcs
Loft Bookshelf
Side rails
24 Pc
Guardrails
TOOLS NEEDEDPARTS LIST QTY PARTS LIST QTY HARDWARE LIST QTY
4 Pcs
Casters
3
4
Full slats
2 Pc
54 Pc
11 Pc
81 Pc
24 Pcs
Phillips screwdriver (not included)
5/16"-18 x 3 3/8" Bolt
Full top bunk bed end
1 Pc
Allen wrench (included)
Full bunkbed end 5 mm Hex key
LOFT BOOKCASE
38000232 100-645 TWIN SLAT PACK (4)
36840418 40B-707 TWIN CASTER BED HD & FT
36040412 40B-711 LOFT CHEST
P A R T S L I S T
RTG SKU # STYLE # ITEM DESCRIPTION
35840405 40G-160 STEP STORAGE UNIT
36040400 40G-711 LOFT CHEST
36640402 40G-730
6 PC RAILS (2 GUARD & 4 SIDE RAILS)
36840406 40G-707 TWIN CASTER BED HD & FT
2 Pcs
6 x 1 1/4"
Drywall screw
36540400 40G-702 FULL EXT KIT
35940407 40G-703 FULL TOP BUNKBED END
36340406 40G-760 LOFT BOOKCASE
RTG SKU # STYLE # ITEM DESCRIPTION
38000232 100-645 TWIN SLAT PACK (4)
38300238 100-648 FULL/FULL SLAT PACK
35940419 40B-703
38300238 100-648 FULL/FULL SLAT PACK
36240416 40B-601 FOLDING DESK (Add on)
3964040P FULL/TWIN STEP LOFT W/ CHEST & BOOKCASE CHARCOAL
3964041P FULL/TWIN STEP LOFT W/ CHEST & BOOKCASE CHESTNUT
FOLDING DESK HARDWARE
FULL LOFT END
36640414 40B-730
6 PC RAILS (2 GUARD & 4 SIDE RAILS)
35840417 40B-160 STEP STORAGE UNIT
36540412 40B-702 FULL EXT KIT
36240404 40G-601 FOLDING DESK (Add on)
36340418 40B-760
A
B
C
D
E
F
H
G
C

CASES ON THE LEFT CASES ON THE RIGHT
CASES ON THE RIGHT CASES ON THE LEFT
remove third drawer, for Left remove center molding and open the door. Remove fastening board and save for next step.
11/7/2022 Page 81 of 97
FIRST DETERMINE THE CONFIGURATION THAT FITS YOUR ROOM
First choose which configuration fits your room ( left or right),
For Right remove center molding by lifting up then pulling out, then
Assemble bookshelf and chest, using the fastening board and bolts previously removed, align both pieces and tight completely as shown.
ASSEMBLY INSTRUCTIONS
STEP 3
STEP 2 STEP 1 B
B
B

and outside pattern and holes. Fasten and make sure all bolts are tightened completely.
Install slats, one on each end and two equally spaced in the middle,
Assemble top side rails. then fasten with 1 1/4" screws
ASSEMBLY INSTRUCTIONS
For stairs on the left, first remove the screw, then remove the panel
Assemble loft chest, loft bookshelf and top bunk bed end. and install it on the other side and secure with the screw.
Assemble step bunk unit and extension kit, aligning inside
11/7/2022 Page 82 of 97
STEP 8
STEP 5
STEP 6
STEP 4
STEP 7
D
D
D
D
B
B
A
STEP 9
F
G
A
A
A
B
C
FG
H
H
H
F
C
C

97
Install slats, one on each end and two equally spaced in the middle,
then fasten with 1 1/4" screws Install casters in headboard and footboard.
ASSEMBLY INSTRUCTIONS
Assemble guardrails and tighten all bolts. Assemble side rails
MAKE SURE ALL BOLTS ARE TIGHTENED COMPLETELY MAKE SURE ALL BOLTS ARE TIGHTENED COMPLETELY
Slide Caster bed under Loft bed as shown.
11/7/2022 Page 83 of
STEP 10
STEP 11
A
B
A
A
A
A
A
A
B
STEP 12
C
E
E
STEP 14
B
A
B
A
C
G
G
STEP 13

Twin size mattress- 74" - 75" long and 37-1/2" - 38-1/2" wide
Twin size Bunkie board- 74" long and 37-1/2" wide
Full size mattress- 74" - 75" long and 52-1/2" - 53-1/2" wide
Full size Bunkie board- 74" long and 52-1/2" wide
ASSEMBLY INSTRUCTIONS
Place Bunkie boards (required, sold separately) on top of the slats
Use only correct mattress dimensions and Bunkie board:
PLEASE CONTACT YOUR RETAIL STORE WITH SERVICE OR PARTS REPLACEMENT REQUEST
11/7/2022 Page 84 of 97
STEP 15

ASSEMBLY INSTRUCTIONS
11/7/2022 Page 85 of 97
Remove center molding by lifting up then pulling out Unfold desk leg and look for hardware pack inside desk box.
Secure each corner block with 1 1/4" screw
Unfold corner supports (from desk box hardware pack) in the pre-bore hole.
Place folding desk by sliding into the opening of loft chest
then push down
STEP 16
STEP 18
STEP 17
STEP 19
STEP 20
C
C