ROOMS TO GO KIDS CREEKSIDE 2.0 3724440P User manual

WARNING DANGER
Failure to follow these warnings and assembly instructions could result in serious
injury or death. To help prevent serious or fatal injuries from entrapment or falls:
-
Read all instructions before assembling bunk bed and keep these instructions for future reference.
-
Before each usage or assembly, inspect bunk bed for damaged hardware, loose joints, missing
parts, or sharp edges. DO NOT Use bunk bed if any parts are missing or broken.
-
DO NOT Use substitute parts. Contact your local Rooms To Go or visit www.ROOMSTOGO.COM
for replacement parts and instructional literature if needed.
-
Follow the information on the warnings appearing on the upper bunk end structure and on the carton,
DO NOT REMOVE WARNING LABEL FROM BED.
-
Always use the recommended size mattress or mattress supports, or both to help prevent the likelihood
of entrapment or falls.
-Ensure thickness of mattress and foundation combine does not exceed
10 inches (255mm
) and
mattress surface is at least
5 inches (127mm)
below upper edge of guardrails.
-
Do not allow children under 6 years of age to use the upper bunk.
-
Periodically check and ensure that the guardrail, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
-
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
-
Limit top bunk use to one person.
-
Always use the ladder for entering and leaving the upper bunk.
-
Use of night light may provide added safety precaution for a child using the upper bunk.
-
Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed next to
the wall, the guardrail that runs the full length of the bed should be placed against the wall to
prevent entrapment between the bed and wall.
-
The use of water or sleep flotation mattress is prohibited.
-
This bunk bed meets all the requirements of ASTM 1427-19.
STRANGULATION HAZARD:
Never attach or hang items to any part of the bunk bed that are not designed for
use with the bed; for example, but not limited to, hooks, belts, and jump ropes.
CREEKSIDE 2.0 COLLECTION
THANK YOU FOR YOUR PURCHASE
11/7/2022 Page 1 of 97

P A R T S L I S T
3724440P TWIN/TWIN LOFT W/LOFT DESK & CHEST CHARCOAL
RTG SKU # STYLE # ITEM DESCRIPTION
35740403 40G-705 TWIN LOFT END
36640402 40G-730 6 PC RAILS (2 GUARD & 4 SIDE RAILS)
36140402 40G-710 LOFT DESK
35740403 40G-705 TWIN LOFT END
36840406 40G-707 TWIN CASTER BED HD & FT
36240404 40G-601
36440408 40G-721 LADDER
38000232 100-645 TW. SLAT PACK (4)
36040400 40G-711 LOFT CHEST
37040401 40G-735 TWIN RAIL CAP
FOLDING DESK (Add on)
35740415 40B-705 TWIN LOFT END
36840418 40B-707 TWIN CASTER BED HD & FT
RTG SKU # STYLE # ITEM DESCRIPTION
35740415 40B-705 TWIN LOFT END
36040412 40B-711 LOFT CHEST
37040413 40B-735 TWIN RAIL CAP
36640414 40B-730 6 PC RAILS (2 GUARD & 4 SIDE RAILS)
36140414 40B-710 LOFT DESK
TOOLS NEEDED
12 Pc
71 Pc
24 Pcs
Phillips screwdriver (not included)
5/16"-18 x 3 3/8" Bolt
PARTS LIST QTY PARTS LIST QTY HARDWARE LIST QTY
32 Pc
Drywall screw
4 Pcs
Twin top bunk bed end
1 Pc
Allen wrench (included)
24 Pc Ladder 5 mm Hex key
FOLDING DESK HARDWARE
2 Pcs
Guardrails Loft chest 3/8" x 3 1/8"
Metal pin 6 x 1 1/4"
81 Pc
16 Pcs
Side rails 6 x 1 1/4"
Casters
Twin slats Caster bed headboard
51 Pc 10 1 Pc
48 Pc 91 Pc 4 Pcs
Twin rail cup Caster bed footboard
Drywall screw
6 Pcs
1" Screws
Page 58 of 97
61 Pc
Loft desk
2 Pcs
Ladder Hook
11 1 Pc
38000232 100-645 TW. SLAT PACK (4)
36440410
3724441P TWIN/TWIN LOFT W/LOFT DESK & CHEST CHESTNUT
38000232 100-645 TW. SLAT PACK (4)
36240416 40B-601 FOLDING DESK (Add on)
40B-721 LADDER
38000232 100-645 TW. SLAT PACK (4)
Folding desk (Add on)
11/7/2022
A
B
C
D
C
E
F
G

Assemble loft chest and top bunk bed end.
ASSEMBLY INSTRUCTIONS
then fasten with 1 1/4" screws MAKE SURE ALL BOLTS ARE TIGHTENED COMPLETELY
11/7/2022 Page 59 of 97
Assemble loft chest and top bunk bed end. Assemble top side rails.
Install slats, one on each end and two equally spaced in the middle, Assemble guardrails and tighten all bolts.
STEP 5
STEP 4
STEP 1
C
D
B
CA
D
D
A
D
D
STEP 3
STEP 2 D
A
B
A
A
A
A
B
B
C
A
A
AA
B

Install casters in headboard and footboard, and set rail cup. Slide Caster bed under Loft bed as shown.
ASSEMBLY INSTRUCTIONS
Screw ladder hooks to pre-drilled holes on top of ladder.
11/7/2022 Page 60 of 97
Screw ladder to guardrail as shown.
Assemble side rails Install slats, one on each end and two equally spaced in the middle,
MAKE SURE ALL BOLTS ARE TIGHTENED COMPLETELY then fasten with 1 1/4" screws
STEP 6
STEP 8
B
A
A
A
A
C
STEP 7
STEP 9
E
STEP 10
E
A
B
E
C
STEP 11
F
F
F
F
FF

Twin size mattress- 74" - 75" long and 37-1/2" - 38-1/2" wide
Twin size Bunkie board- 74" long and 37-1/2" wide
Full size mattress- 74" - 75" long and 52-1/2" - 53-1/2" wide
Full size Bunkie board- 74" long and 52-1/2" wide
ASSEMBLY INSTRUCTIONS
Place Bunkie boards (required, sold separately) on top of the slats
Use only correct mattress dimensions and Bunkie board:
PLEASE CONTACT YOUR RETAIL STORE WITH SERVICE OR PARTS REPLACEMENT REQUEST
11/7/2022 Page 61 of 97
STEP 12

Remove center molding by lifting up then pulling out Unfold desk leg and look for hardware pack inside desk box.
Secure each corner block with 1 1/4" screw
ASSEMBLY INSTRUCTIONS
11/7/2022 Page 62 of 97
Unfold corner supports (from desk box hardware pack) in the pre-bore hole.
Place folding desk by sliding into the opening of loft chest
then push down
STEP 13
STEP 15
STEP 14
STEP 16
STEP 17
C
C

Twin size mattress- 74" - 75" long and 37-1/2" - 38-1/2" wide
Twin size Bunkie board- 74" long and 37-1/2" wide
Full size mattress- 74" - 75" long and 52-1/2" - 53-1/2" wide
Full size Bunkie board- 74" long and 52-1/2" wide
ASSEMBLY INSTRUCTIONS
11/7/2022 Page 63 of 97
Use only correct mattress dimensions and Bunkie board:
PLEASE CONTACT YOUR RETAIL STORE WITH SERVICE OR PARTS REPLACEMENT REQUEST
Place Bunkie boards (required, sold separately) on top of the slats
STEP 18