ROSE DISPLAYS ANOMULTI SQUARE WITH CABLE CLIP AND BALL... User manual

35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Parts
Instruction Sheet
Step 1
Insert the poster into the Slim Holder by either
sliding the poster into the holder or tapping the
holder onto the poster. . Fig. 1
Note: For thinner substrates, it may be necessary
to staple the edge of the graphic before inserting
into Slim Holder.
Step 2
Slide Slim holder into AnoMulti holder. Fig. 2
Step 3
Insert single ball of ball chain into inner channel of
Cable Clip. The cable should snap into place.
Fig. 3
Step 4
Align one round end of cable clip with top channel
of the aluminum rail and insert. Once in place,
insert end of ball chain into channel. Then press
down on the other round end of the cable clip and
slide into rail by pushing on the clip. Fig. 4
Note: Be sure to slide the ball chain into place by
pushing on the cable clip. Do not pull on, or
push against, the ball chain as this will cause it to
bind in the channel.
Step 5
Push end caps into place. Fig. 5
Step 6
Suspend poster. Fig. 6
AnoMulti™
Instructions for Hanging
Incept-7.4.02
Figure 1 Figure 2
The AnoMulti™ and Slim™are trademarks of Rose Displays, Ltd.
Neither the manufacturer nor any sales agent may be held liable for
injury, loss or damage resulting from the use of these products.
Part #02INSAnoMultiSQCableClipBallChain
Figure 6Figure 5
Figure 3 Figure 4
AnoMulti
12AM300SQ
End Caps
06-5545
Cable Clips
06-5050
Ball Chains
96-0302P

35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Parts
Instructions for Hanging
Instruction Sheet
Step 1
Insert the poster into the Slim Holder by either
sliding the poster into the holder or tapping the
holder onto the poster. . Fig. 1
Note: For thinner substrates, it may be necessary to
staple the edge of the graphic before inserting into
Slim Holder.
Step 2
Slide Slim holder into AnoMulti holder. Fig. 2
Step 3
Insert single ball of ball chain into inner channel of
Cable Clip. The cable should snap into place. Fig. 3
Step 4
Align one round end of cable clip with top channel of
the aluminum rail and insert. Once in place, insert
end of ball chain into channel. Then press down on
the other round end of the cable clip and slide into
rail by pushing on the clip. Fig. 4
Note: Be sure to slide the ball chain into place by
pushing on the cable clip. Do not pull on, or push
against, the ball chain as this will cause it to bind in
the channel.
Note: For OneUp applications, the AnoMulti Holder
is conveniently marked in the center.
Slide the Cable Clip to the mark.
Step 5
Push end caps into place. Fig. 5
Step 6
Suspend poster.
AnoMulti™
Incept-7.4.02
Figure 1 Figure 2
The AnoMulti™ and Slim™are trademarks of Rose Displays, Ltd.
Neither the manufacturer nor any sales agent may be held liable for
injury, loss or damage resulting from the use of these products.
Part #02INSAnoMultiSQCableClipBallChain
Figure 6Figure 5
Figure 3 Figure 4
AnoMulti
12AM300SQ
End Caps
06-5545
Cable Clip
06-5050
Ball Chain
96-0302P

Parts
Instruction Sheet
AnoMulti™
Instructions for Hanging
Incept-7.4.02
Figure 1 Figure 2
The AnoMulti™ and Slim™are trademarks of Rose Displays, Ltd.
Neither the manufacturer nor any sales agent may be held liable for
injury, loss or damage resulting from the use of these products.
Part #02INSAnoMultiSQCableClipBallChain
Figure 6Figure 5
Figure 3 Figure 4
AnoMulti
12AM300SQ
End Caps
06-5545
Cable Clips
06-5050
Ball Chains
96-0302P
Step 1
Insert the poster into the Slim Holder by either
sliding the poster into the holder or tapping the
holder onto the poster. . Fig. 1
Note: For thinner substrates, it may be necessary
to staple the edge of the graphic before inserting
into Slim Holder.
Step 2
Slide Slim holder into AnoMulti holder. Fig. 2
Step 3
Insert single ball of ball chain into inner channel of
Cable Clip. The cable should snap into place.
Fig. 3
Step 4
Align one round end of cable clip with top channel
of the aluminum rail and insert. Once in place,
insert end of ball chain into channel. Then press
down on the other round end of the cable clip and
slide into rail by pushing on the clip. Fig. 4
Note: Be sure to slide the ball chain into place by
pushing on the cable clip. Do not pull on, or
push against, the ball chain as this will cause it to
bind in the channel.
Step 5
Push end caps into place. Fig. 5
Step 6
Suspend poster. Fig. 6

Parts
Instructions for Hanging
Instruction Sheet
AnoMulti™
Incept-7.4.02
Figure 1 Figure 2
The AnoMulti™ and Slim™are trademarks of Rose Displays, Ltd.
Neither the manufacturer nor any sales agent may be held liable for
injury, loss or damage resulting from the use of these products.
Part #02INSAnoMultiSQCableClipBallChain
AnoMulti
12AM300SQ
Figure 6Figure 5
Figure 3 Figure 4
End Caps
06-5545
Cable Clip
06-5050
Ball Chain
96-0302P
Step 1
Insert the poster into the Slim Holder by either
sliding the poster into the holder or tapping the
holder onto the poster. . Fig. 1
Note: For thinner substrates, it may be necessary to
staple the edge of the graphic before inserting into
Slim Holder.
Step 2
Slide Slim holder into AnoMulti holder. Fig. 2
Step 3
Insert single ball of ball chain into inner channel of
Cable Clip. The cable should snap into place. Fig. 3
Step 4
Align one round end of cable clip with top channel of
the aluminum rail and insert. Once in place, insert
end of ball chain into channel. Then press down on
the other round end of the cable clip and slide into
rail by pushing on the clip. Fig. 4
Note: Be sure to slide the ball chain into place by
pushing on the cable clip. Do not pull on, or push
against, the ball chain as this will cause it to bind in
the channel.
Note: For OneUp applications, the AnoMulti Holder
is conveniently marked in the center.
Slide the Cable Clip to the mark.
Step 5
Push end caps into place. Fig. 5
Step 6
Suspend poster.