ROSE DISPLAYS ANOQUICK ROUND WITH MULTICLIPS User manual

35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Parts
Instruction Sheet
Step 1
Prepare edges of graphic. Place the graphic on
tabletop with one edge at the table edge. Using
the AnoQuick holder, run it across the graphic
edge, crushing it slightly. Fig. 1
Step 2
Starting at one corner, push the holder onto the
graphic. Work your way down the holder tapping
it down firmly to seat the graphic fully. Fig. 2
Step 3
Squeeze sides of MultiClip together. Fig.3
Step 4
Align the bottom rail of the MultiClip with
the top channel of the aluminum holder. Slide
MultiClip into rail. Fig. 4 Repeat steps 3 & 4
for second MultiClip.
Step 5
Push end caps into place. Fig. 5
Step 6
Suspend poster. Fig. 6
Important note:
Please save and reuse the AnoQuick holder,
End Caps and MultiClips for future projects.
MultiClips
1UP-0101
End Caps
06-5525
Note: Use only
with graphics
mounted on 3/16”
foamboard or other
similar thickness.
Can also use a
folded edge thinner
substrate.
AnoQuick™
Instructions for Hanging
Incept-7.31.02
Figure 2
AnoQuick
12A300
AnoQuick is a trademark. Neither the manufacturer nor any sales agent
may be held liable for injury, loss or damage resulting from the use of
these products. Part #02INSAnoQuickMC
Figure 3
Figure 5
Figure 4
Figure 1
Figure 6

35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Parts
Note: Use only
with graphics
mounted on 3/16”
foamboard or other
similar thickness.
Can also use a
folded edge thinner
substrate.
Instructions for Hanging
OneUp
®
Instruction Sheet
Step 1
Prepare edges of graphic. Place the graphic on
tabletop with one edge at the table edge. Using
the AnoQuick holder, run it across the graphic
edge, crushing it slightly. Fig. 1
Step 2
Starting at one corner, push the holder onto the
graphic. Work your way down the holder tapping
it down firmly to seat the graphic fully. Fig. 2
Step 3
Squeeze sides of MultiClip together. Fig.3
Step 4
Align the bottom rail of the MultiClip with
the top channel of the aluminum holder. Slide
MultiClip into rail. Fig. 4
Step 5
Push end caps into place. Fig. 5
Step 6
Suspend poster. Fig. 6
Important note:
Please save and reuse the AnoQuick holder,
End Caps and MultiClip for future projects.
AnoQuick™
Incept-7.31.02
End Caps
06-5525
AnoQuick
12A300
AnoQuick is a trademark. Neither the manufacturer nor any sales agent
may be held liable for injury, loss or damage resulting from the use of
these products. Part #02INSAnoQuickMC
MultiClip
1UP-0101
Figure 2
Figure 3
Figure 5
Figure 4
Figure 1
Figure 6

Parts
Note: Use only
with graphics
mounted on 3/16”
foamboard or other
similar thickness.
Can also use a
folded edge thinner
substrate.
Instructions for Hanging
Instruction Sheet
AnoQuickTM
Incept-7.31.02
End Caps
06-5525
AnoQuick
12A300
AnoQuick is a trademark. Neither the manufacturer nor any sales agent
may be held liable for injury, loss or damage resulting from the use of
these products. Part #02INSAnoQuickMC
MultiClips
1UP-0101
Step 1
Prepare edges of graphic. Place the graphic on
tabletop with one edge at the table edge. Using
the AnoQuick holder, run it across the graphic
edge, crushing it slightly. Fig. 1
Step 2
Starting at one corner, push the holder onto the
graphic. Work your way down the holder tapping
it down firmly to seat the graphic fully. Fig. 2
Step 3
Squeeze sides of MultiClip together. Fig.3
Step 4
Align the bottom rail of the MultiClip with
the top channel of the aluminum holder. Slide
MultiClip into rail. Fig. 4 Repeat steps 3 & 4
for second MultiClip.
Step 5
Push end caps into place. Fig. 5
Step 6
Suspend poster. Fig. 6
Important note:
Please save and reuse the AnoQuick holder,
End Caps and MultiClips for future projects.
Figure 2
Figure 3
Figure 5
Figure 4
Figure 1
Figure 6
Incept-7.31.02

Parts
Note: Use only
with graphics
mounted on 3/16”
foamboard or other
similar thickness.
Can also use a
folded edge thinner
substrate.
Instructions for Hanging
OneUp
®
Instruction Sheet
AnoQuick™
Incept-7.31.02
End Caps
06-5525
AnoQuick
12A300
AnoQuick is a trademark. Neither the manufacturer nor any sales agent
may be held liable for injury, loss or damage resulting from the use of
these products. Part #02INSAnoQuickMC
MultiClip
1UP-0101
Step 1
Prepare edges of graphic. Place the graphic on
tabletop with one edge at the table edge. Using
the AnoQuick holder, run it across the graphic
edge, crushing it slightly. Fig. 1
Step 2
Starting at one corner, push the holder onto the
graphic. Work your way down the holder tapping
it down firmly to seat the graphic fully. Fig. 2
Step 3
Squeeze sides of MultiClip together. Fig.3
Step 4
Align the bottom rail of the MultiClip with
the top channel of the aluminum holder. Slide
MultiClip into rail. Fig. 4
Step 5
Push end caps into place. Fig. 5
Step 6
Suspend poster. Fig. 6
Important note:
Please save and reuse the AnoQuick holder,
End Caps and MultiClip for future projects.
Figure 2
Figure 3
Figure 5
Figure 4
Figure 1
Figure 6