ROSE DISPLAYS SPIDER RING WITH CABLE AND SAUCER User manual

Parts
35 Congress Street, Salem MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Instructions For Hanging
Step 1
Push Saucer up through large hole in bottom of
spider anchor. Fig. 1
Step 2
Slide Saucer into pocket next to the hole. Pull
cable tight. Fig. 2
Step 3
Insert Saucer into top rail of the holder. Fig. 3
Note: It is easiest to slide the Saucer into the
holder if you hold the cable as close to the Saucer
as possible. Fig. 4
Step 4
For directions on how to use a specific holder to
hang your poster, refer to the appropriate instruc-
tion sheet. Fig. 5
Instruction Sheet
Spider RingTM with Cable and Saucer
Incept-5.02.02
Figure 1 Figure 2
The Spider Anchor and Spider Ring are trademarks of Rose Displays, Ltd.
Neither the manufacturer nor any sales agent may be held liable for
injury, loss or damage resulting from the use of these products.
Part #02INSSpiderRingCable&Saucer
Figure 4Figure 3
Cable and
Saucer
16-0018SS
Spider Anchor
RAN-BASE-CC
Spider Ring
16-0018R

Parts
35 Congress Street, Salem MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Important note:
Spider Rings can be attached before or after
suspending sign. If the rings need to be posi-
tioned out of reach, or if more than two cable
wraps are required per ring, wrap the cable
around the rings before sign is hung.
Step 5
Place Spider Ring onto the cable. The cable
goes inside the ring’s outer groove. Fig. 6
Step 6
With the cable inside the groove, wrap it once
around the ring. Fig. 7
Step 7
While holding the ring, pull down on
cable until it pops into the groove. Fig. 8
Repeat steps 1-3 for multiple wrappings.
Note: Each wrap shortens the cable by 3”.
Maximum of 6 wraps or 18” per Spider Ring.
Multiple rings can be used on each cable for
more adjustability.
Step 8
Repeat steps 1-3 for each cable used to hang
your sign.
Step 9
Slide the Spider Rings up and out of view. Fig 9
& 10. Note: To lengthen cable, unwind one
or more wraps from each Spider Ring.
Instructions for assembly
Incept-5.02.02
The Spider Anchor and Spider Ring are trademarks of Rose Displays, Ltd.
Neither the manufacturer nor any sales agent may be held liable for
injury, loss or damage resulting from the use of these products.
Part #02INSSpiderRingCable&Saucer
Figure 10
Figure 8 Figure 9
Figure 6 Figure 7
Spider RingTM with Cable and Saucer Instruction Sheet
Spider Anchor
RAN-BASE-CC
Spider Ring
16-0018R
Cable and
Saucer
16-0018SS

Parts
Instructions For Hanging
Step 1
Push Saucer up through large hole in bottom of
spider anchor. Fig. 1
Step 2
Slide Saucer into pocket next to the hole. Pull
cable tight. Fig. 2
Step 3
Insert Saucer into top rail of the holder. Fig. 3
Note: It is easiest to slide the Saucer into the
holder if you hold the cable as close to the Saucer
as possible. Fig. 4
Step 4
For directions on how to use a specific holder to
hang your poster, refer to the appropriate instruc-
tion sheet. Fig. 5
Instruction Sheet
Spider RingTM with Cable and Saucer
Incept-5.02.02
Figure 1 Figure 2
The Spider Anchor and Spider Ring are trademarks of Rose Displays, Ltd.
Neither the manufacturer nor any sales agent may be held liable for
injury, loss or damage resulting from the use of these products.
Part #02INSSpiderRingCable&Saucer
Figure 4Figure 3
Spider Anchor
RAN-BASE-CC
Spider Ring
16-0018R
Cable and
Saucer
16-0018SS

Parts
Important note:
Spider Rings can be attached before or after
suspending sign. If the rings need to be posi-
tioned out of reach, or if more than two cable
wraps are required per ring, wrap the cable
around the rings before sign is hung.
Step 5
Place Spider Ring onto the cable. The cable
goes inside the ring’s outer groove. Fig. 6
Step 6
With the cable inside the groove, wrap it once
around the ring. Fig. 7
Step 7
While holding the ring, pull down on
cable until it pops into the groove. Fig. 8
Repeat steps 1-3 for multiple wrappings.
Note: Each wrap shortens the cable by 3”.
Maximum of 6 wraps or 18” per Spider Ring.
Multiple rings can be used on each cable for
more adjustability.
Step 8
Repeat steps 1-3 for each cable used to hang
your sign.
Step 9
Slide the Spider Rings up and out of view. Fig 9
& 10. Note: To lengthen cable, unwind one
or more wraps from each Spider Ring.
Instructions for assembly
Incept-5.02.02
The Spider Anchor and Spider Ring are trademarks of Rose Displays, Ltd.
Neither the manufacturer nor any sales agent may be held liable for
injury, loss or damage resulting from the use of these products.
Part #02INSSpiderRingCable&Saucer
Figure 10
Figure 8 Figure 9
Figure 6 Figure 7
Spider RingTM with Cable and Saucer Instruction Sheet
Spider Anchor
RAN-BASE-CC
Spider Ring
16-0018R
Cable and
Saucer
16-0018SS