ROSE DISPLAYS ANOQUICK SQUARE WITH GOTCHA AND MULTICLIPS User manual

Parts
35 Congress Street, Salem MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Instructions for Hanging
Step 1
Place poster on a flat surface. Snap the Gotcha
Holder open and insert poster (top and bottom).
To close, snap the Gotcha Holder shut. Fig. 1
Note: It is easier to open and close the Gotcha
Holder by starting at one end and working your
way down the holder.
Step 2
Slide the Gotcha Holder into the AnoQuick
Holder. Fig. 2
Step 3
Install the MultiClips in top AnoQuick Holder.
Holding clip at slight angle, first insert one round
end, then press down on the other round end and
push MultiClip into holder. Insert second
MultiClip. Fig. 3 & 4
Step 4
Push end caps into place. Fig. 4
Note: To remove Gotcha (and sign), simply rotate
end cap up out of the way.
Step 5
Suspend poster.
Important note:
Please save and reuse the AnoQuick Holder,
Gotcha Holder, End Caps and MultiClips for future
projects.
Instruction Sheet
AnoQuick
TM
with Gotcha
®
Insert
Instructions for Hanging
Incept-9.9.02
The AnoQuickTM is a trademark and Gotcha®is a registered trademark of
Rose Displays, Ltd. Neither the manufacturer nor any sales agent may be
held liable for injury, loss or damage resulting from the use
of these products. Part #02INSAnoQuickSQGotchaMC
Gotcha
®
Special
(no clip rail)
AnoQuick
Square Profile
12A300SQ
MultiClip
1UP-0100
Figure 1
Figure 5
Figure 2
Figure 3
Figure 4
Square End Cap
06-5545

Parts
Instructions for Hanging
Step 1
Place poster on a flat surface. Snap the Gotcha
Holder open and insert poster (top and bottom).
To close, snap the Gotcha Holder shut. Fig. 1
Note: It is easier to open and close the Gotcha
Holder by starting at one end and working your way
down the holder.
Step 2
Slide the Gotcha Holder into the AnoQuick
Holder. Fig. 2
Step 3
Install the MultiClips in top AnoQuick Holder.
Holding clip at slight angle, first insert one round
end, then press down on the other round end and
push MultiClip into holder. Insert second
MultiClip. Fig. 3 & 4
Step 4
Push end caps into place. Fig. 5
Note: To remove Gotcha (and sign), simply rotate
end cap up out of the way.
Step 5
Suspend poster.
Important note:
Please save and reuse the AnoQuick, Gotcha Holder,
End Caps and MultiClips for future projects.
Instruction Sheet
AnoQuick
TM
with Gotcha
®
Insert
Instructions for Hanging
Incept-9.9.02
The AnoQuickTM is a trademark and Gotcha®is a registered trademark of
Rose Displays, Ltd. Neither the manufacturer nor any sales agent may be
held liable for injury, loss or damage resulting from the use
of these products. Part #02INSAnoQuickSQGotchaMC
Gotcha
®
Special
(no clip rail)
AnoQuick
Square Profile
12A300SQ
MultiClips
1UP-0100
Square End Caps
06-5545
Figure 1
Figure 5
Figure 2
Figure 3
Figure 4

Parts
35 Congress Street, Salem MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Instructions for Hanging
Step 1
Place poster on a flat surface. Snap the Gotcha
Holder open and insert poster (top and bottom). To
close, snap the Gotcha Holder shut. Fig. 1
Note: It is easier to open and close the Gotcha
Holder by starting at one end and working your way
down the holder.
Step 2
Slide the Gotcha Holder into the AnoQuick
Holder. Fig. 2
Step 3
Install MultiClip in top AnoQuick holder. Holding
clip at slight angle, first insert one round end, then
press down on other round end and push MultiClip
into holder. Fig. 3
Note: For OneUp applications place the MultiClip
in the center of the AnoQuick Holder. Fig. 4
Step 4
Push end caps into place. Fig. 5
Note: To remove Gotcha (and sign), simply rotate
end cap up out of the way.
Step 5
Suspend poster.
Important note:
Please save and reuse the AnoQuick Holder, Gotcha
Holder, End Caps and MultiClips for future projects.
OneUp Instruction Sheet
AnoQuick
TM
with Gotcha
®
Insert
Instructions for Hanging
Incept 9.9.02
The AnoQuickTM is a trademark and Gotcha® is a registered trademark of
Rose Displays, Ltd. Neither the manufacturer nor any sales agent may be
held liable for injury, loss or damage resulting from the use
of these products. Part #02INSAnoQuickSQGotchaMC
Gotcha
®
Special
(no clip rail)
AnoQuick
Square Profile
12A300SQ
MultiClip
1UP-0100
Square End Caps
06-5545
Figure 1
Figure 5
Figure 2
Figure 3
Figure 4

Parts
Instructions for Hanging
Step 1
Place poster on a flat surface. Snap the Gotcha
Holder open and insert poster (top and bottom).
To close, snap the Gotcha Holder shut. Fig. 1
Note: It is easier to open and close the Gotcha
Holder by starting at one end and working your way
down the holder.
Step 2
Slide the Gotcha Holder into the AnoQuick
Holder. Fig. 2
Step 3
Install MultiClip in top AnoQuick Holder. Holding
clip at slight angle, first insert one round end, then
press down on other round end and push MultiClip
into holder. Fig. 3
Note: For OneUp applications place the MultiClip
in the center of the AnoQuick Holder. Fig. 4
Step 4
Push end caps into place. Fig. 5
Note: To remove Gotcha (and sign), simply rotate
end cap up out of the way.
Step 5
Suspend poster.
Important note:
Please save and reuse the AnoQuick Holder, Gotcha
Holder, End Caps and MultiClips for future projects.
OneUp Instruction Sheet
Instructions for Hanging
Incept-9.9.02
The AnoQuickTM is a trademark and Gotcha®is a registered trademark of
Rose Displays, Ltd. Neither the manufacturer nor any sales agent may be
held liable for injury, loss or damage resulting from the use of these
products. Part #02INSAnoQuickSQGotchaMC
Gotcha
®
Special
(no clip rail)
AnoQuick
Square Profile
12A300SQ
MultiClip
1UP-0100
Square End Caps
06-5545
AnoQuick™ with Gotcha
®
Insert
Figure 1
Figure 5
Figure 2
Figure 3
Figure 4