Rosewill CASE 6A Series User manual

CASE 6A series User Manual
1© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
Contents
Configuration
Features Descriptions
Installation
1.Opening Chassis
2.Installing Motherboard
3. Installing Power Supply
4.Installing 5.25" Device
5.Installing 3.5" Floppy
6.Installing 3.5" HDD
7.Installing Add on Card
9.USB port
10.Audio Port
P. 2
P. 3
P. 4
P. 5
P. 6
P. 7
P. 8
P. 9
P.10
P.12
P.13
11.Front Panel LED P.14
12.System Control Connectors P.15
Information P.16
8.Clearing Air Filter P.11

CASE 6A series User Manual
2© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
Configuration
Dimension (W x H x D)
M/B Size
Drive Bay
Expansion Slots
Thermal Solution
Air Filter
I/O Port Bracket
Megal Material
8.3" x 18.1" x 16.9"
ATX, Micro ATX
External : 4 x 5.25" + 2 x 3.5"
Internal : 5 x 3.5"
7Slots
1 x 120 mm fan in rear and 1 x 120 mm fan holder in front
One air filter in the front panel
Supports one I/O port bracket for standard ATX M/B
0.8 mm thickness SECC rustproof & galvanized JIS Steel

CASE 6A series User Manual
3© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
Features Descriptions
Rear 120mm Fan Front 120mm Fan Holder Sliding Rails for 5.25"
Device
Vertical sliding HDD cage
HDD cage with Shockproof
Rubber Pads
Add on Card Kit No Screw Neded to Secure
& Open the Left Side Panel
Front IO Ports

CASE 6A series User Manual
5© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
2.1
Locate and align the screw holes on the
motherboard and chasis; place the
motherboard at the correct position,
and then screw brass studs onto
chasis's metal shell
2.2
Secure the motherboard on the studs with
the screws #6-32
2.Installing Motherboard

CASE 6A series User Manual
6© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
3.1
Put your power supply in the right position and fasten screws from back panel of the case
3.Installing Power Supply

CASE 6A series User Manual
7© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
4.1
Locate the screw holes on both
sides of 5.25"device such as
CD-ROM and screw the rails
onto the 5.25" device
4.2
Insert the railed device into the
5.25" drive bay
4.Installing 5.25" Device
NOTE :
• Recommend to remove the 5.25" metal cover below the bay you
want to install your 5.25" device for easier installation
• When you feel difficult to pull out your railed 5.25" device, push it
down a little will help you

CASE 6A series User Manual
8© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
5.Installing 3.5" Floppy
5.2
Slide the floppy or, if necessary
HDD into the drive bay
5.4
Slide the small cage into drive
bay, make sure the cate is
properly positioned
5.1
Pull the handle and cage back-
wards to take off the small cage
5.3
Fasten the floppy on cage by
screws

CASE 6A series User Manual
9© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
6.Installing 3.5" HDD
6.2
Push the handle down and pull
the large cage out
6.4
Screw up and fasten HDD on the
cage
*Handle with care because
HDD is likely to be damaged by
careless management
6.1
Take off the thumb screw on the
large cage
6.3
Slide the HDD into the drive bay
6.5
Slide the large cage into drive
bay and fasten the thumb screws