rosseto EZ-PRO 1W User manual

NEED ASSISTANCE? Please contact our customer service support at [phone]
and we’ll be happy to assist with any assembly questions,
comments, or concerns.
ROSSETO® 3714 Jarvis Avenue, Skokie, IL 60076
Visit our website att www.rosseto.com
EZ-PRO™ Wallmount Dispenser
SETTING UP YOUR PRODUCT
c. ITEM #:
EZP021
b. ITEM #:
EZP028
e. CONTAINER SHELL:
ITEM #: EZC038
2 hooks on the back of the EZ-PROTM
container latch on to the upper and
lower notches on the stand.
f. ITEM #: EZH010
Models: EZ501:EZ-PRO™ 1W EZP2906: EZ-PRO™ 3W EZP2890: EZ-PRO™ 5W
d. ITEM #:
EZP022
1. Carefully remove all parts from packaging and poly bags.
2. Make sure you have all parts listed before discarding packaging.
• 1 EZ-PRO™ Metal Bracket
• Depending on your model, you will have 1, 3 or 5 EZ-PRO™ containers with:
a. Lid
b. 1, 2, 3 & 4 tsp. Portioned Scoops and Funnel
c. PRO-6W Silicon Portion Wheel (1 oz.)
d. PRO-6SM Portion Wheel (1 tbsp.)
e. Container
f. Handle
3.Consult your contractor about what mounting hardware (not included) to
use, depending on the type of wall you have.
4.Mount EZ-PRO™ metal bracket where desired, making sure it is a󰀩xed
securely to the wall.
5.Fill an EZ-PRO™ container with desired product and seal with the lid.
6.On the back of each container are 2 hooks that t snugly onto the allotted
notches on the stand. Install a containerby securing both hooks on the upper
and lower notches.Make sure it locks into place.
7.Repeat steps 5 through 7 for the remaining containers.
8.Dispense as you please!
37.5 cm (14.8”)11.4 cm (4.4”)
17.1 cm (6.7”)
37.8 cm
(14.8”)
13.5 cm
(5.3”)
3 cm (1.2”)
39 cm (15.4)
63.4 cm (25”)
65 cm (25.6”)
39 cm (15.4”)
a. ITEM #: EZL006

NEED ASSISTANCE? Please contact our customer service support at [phone]
and we’ll be happy to assist with any assembly questions,
comments, or concerns.
ROSSETO® 3714 Jarvis Avenue, Skokie, IL 60076
Visit our website att www.rosseto.com
EZ-PRO™ Wallmount Dispenser
CLEANING INSTRUCTIONS:
1. To maintain the quality of your EZ-PRO™ container, wash all parts in warm, soapy water. Use a non-abrasive sponge.
2. DO NOT put any part of the unit through any dishwasher, dryer machines, or submerge in water.
3. When disassembling the container, handle all parts gently. Please refrain from using too much force.
4. Reassemble the unit only after all parts are completely dry.
HOW TO DISASSEMBLE:
1. Remove the container from the stand by holding it securely and lifting directly upward, clearing the hooks from the
notches on the stand.
2. Remove lid from top of container. Make sure there is no remaining product inside that can spill over.
3. Gently pull the handle from the front of the container. Set aside.
4. Reach into container and remove portion wheel by gently pulling upwards.
HOW TO ASSEMBLE:
1. Place portion wheel into container.
2. Adjust the portion wheel inside the container, so that its holes align with the container’s holes (both front and back).
3. Then insert the handle through the front by aligning the half-moon shaft with the paddle.
4. Fill container with desired dry product and place lid securely on the container.
6. On the back of each container are 2 hooks that t snugly onto the allotted notches on the stand. Install a container by
securing both hooks on the upper and lower notches. Make sure it locks into place.
5. Continue using dispenser unit as usual.
The Rosseto interchangeable portion wheels deliver just the right amount of product every time. Test each
wheel with your dry foods to determine which works best for you!
CARING FOR YOUR CONTAINER
IS003 V3 - MAR 2019