rosseto EZ-PRO 2 User manual

Your EZ-PRO™ 2/3/5 Table-Top Dispenser comes with the PRO-6W Silicon Portion
Wheel (1 oz).This portion wheel is perfect for dispensing items such asmedium grind
cookies, cereals & granolas, trail mixes andcoffee beans!
1. Carefully remove allparts from packaging andpoly bags.
•1 Stainless Steel Stand with
detachable Base and Tray
c. Regular Nozzle
d. Container
e.
Handle
f.
Label Holder
2.
3. Place the stand on a flat surface facing you.
4. Set the base on the stand and place the tray on top of it.
6.On the back of each container are 2 hooks that fit snugly onto the allotted notches on the stand. Install a
container by securing both hooks on the upper and lower notches. Make sure it locks into place.
8.Repeat steps 5 thru 7 for the remaining containers.
9.Dispense as you please!
EZ-PRO™ 2/3/5 (EZP2746/EZP2135/EZP2883)
SETTING UP YOUR PRODUCT
Please contact our customersupport at [phone] and we’ll be
happy to assist with any assemblyquestions, comments or concerns.
ROSSETO®3600 W. Pratt Avenue. Lincolnwood, IL 60712
Visitour website at: www.rosseto.com
NEEDASSISTANCE?
ITEM # EZL006
ITEM # EZP004
ITEM # EZM005
a
b
c
ITEM # EZH008
g HANDLE AND CLIP:
e ITEM # EZM006
ITEM # EZL009
d
CONTAINER SHELL:
ITEM # EZC008
f
•Depending on your model, you will have 2, 3 or 5 EZ-PRO™ containers each with:
a. Lid
b. PRO-6W Silicon Portion Wheel
BASE
TRAY
h
g.
PRO Fresh Lid
h.Handle Clip
Make sure you have allparts listed above before discarding packaging.
5.Fill an EZ-PRO™ container with desired product and seal with the lid.
7. If desired, you may place an identifying label on the label holder.
2 hooks on the back of the
EZ-PROTM container latch
on to the upper and lower
notches on the stand.
EZ-PROTM 2: ITEM # EZP2746
EZ-PROTM 3: ITEM # EZP2135
EZ-PROTM 5: ITEM # EZP2883

CLEANING INSTRUCTIONS:
1. To maintain the quality of your EZ-PRO™ container, wash all parts daily in warm soapy water.Use a non-abrasive sponge.
2. When disassembling the container, handle all parts gently. Please refrain from using too much force.
3. Reassemble the unit only after all parts are completely dry.
HOW TO DISASSEMBLE:
1. Remove the container from the stand by holding it securely and lifting directly upward, clearing the hooks from the
notches on the stand.
2.Remove lid from top of container. Make sure there is no remaining product inside that can spill over.
3.Remove handle clip at the back of the container.
4.Gently pull the handle from thefront of thecontainer. Set aside both handle and label holder.
5.Reach into container andremove portion wheel bygently pulling upwards orturning container upside down. Do the
same to remove the nozzle.
HOW TO ASSEMBLE:
1. Place nozzleinto container, followed by the portion wheel.
3.Position the label holder so that it matches the hole on the front of the container.
5.Place handle clip on the back end ofthe shaft. Make sure the words “This Side Out” are facing out.
6.Fill container with desired dry product and place lid securely on the container.
7.Follow steps 6and 7 on Page 1.
Need a different-sized portion wheel? We have 6 more options for you tochoose from!
Other portion wheels available:
•Pro6-SM– 1 tablespoon
•EZP007 – 1 teaspoon
•EZP008 – 2teaspoons
•EZP010– 3teaspoons
•EZP011– 4.5 teaspoons
The Rosseto interchangeable portion wheels deliver just the right amount of product
every time. Test each wheel with your dry foods to determine which works best foryou!
Please contact our customersupport at [phone] and we’ll be
happy to assist with any assemblyquestions, comments or concerns.
ROSSETO®3600 W. Pratt Avenue. Lincolnwood, IL 60712
Visitour website at: www.rosseto.com
NEEDASSISTANCE?
CARING FOR YOUR CONTAINER
2.Adjust the portion wheel inside the container, so that its holes align with the container’s holes (both front and back).
4.Insert handle through the label holder and front hole. Push the shaft through the portion wheel, all the way to
the back of the container.