rosseto EZ-PRO C4L User manual

e
1. Carefully remove all parts from packaging and poly bags.
•4 easy-to-install back snap system (optional accessory)
c.
g.
h.
f. Narrow Nozzle
Container
Label Holder
Handle
Handle Clip
i.
2.
3.
4.
Please contact our customersupport at [phone] and we’ll be
happy to assist with any assemblyquestions, comments or concerns.
ROSSETO®3600 W. Pratt Avenue. Lincolnwood, IL 60712
Visitour website at: www.rosseto.com
NEEDASSISTANCE?
ITEM # EZL006
ITEM # EZP004
ITEM # EZM005
a
b
i ITEM # EZH012
h ITEM # EZM006
g
CONTAINER SHELL:
ITEM # EZC008
•You will have 4 EZ-PRO™ containers each with:
a.
b.
Stainless steel lid
3 interchangeable portion wheels:
j
j.
k. PRO Fresh Lid
5.
PRO 6-Wing Silicon 1 oz. Portion Wheel
PRO-6SM 1 tbsp.
d. EZP007 1 tsp. Scoop-It TM with Funnel
2 interchangeable nozzles:
e. Regular Nozzle
•
•
c ITEM # PRO6-SM
ITEM # EZM004
f
ITEM # EZM056
6. Fill an EZ-PRO™ container with desired product and seal with the lid.
d ITEM # EZP007
kITEM # EZL009
•
SETTING UP YOUR PRODUCT
EZ-PRO™ C4L (EZP2760)
Your EZ-PRO™ 4-container Carousel has a 6-inch clearance, making it the perfect table-top dispenser for
both cereal and topping products. This model is a space-saving stylish solution for your dispensing needs!
1 Assembled EZ-PRO™ C4L metal base with pole and detachable tray
Make sure you have all parts listed above before discarding packaging.
Place the metal base on a flat surface.
Check if the tray and the pole are set securely on the base.
Check the portion wheels installed and make sure you use the right fit for each product you are dispensing.
NOTE: If you need to change any portion wheels, follow steps 2 thru 5 on the disassembly instructions on Page 2.
TRAY
POLE
9. Repeat steps 5 thru 7 for the remaining containers.
10. Dispense as you please!
8. If desired, place an identifying label on the label holder.
7. On the back of each container are 2 hooks that fit snugly
onto the allotted notches on the pole. Install a container by
securing both hooks on the upper and lower notches. Make
sure it locks into place.
2 hooks on the back of
the EZ-PROTM container
latch on to the upper
and lower notches on
the pole.
NOTE: Included with each
container unit is an optional
locking system that you can
easily install with a small
Phillips head screwdriver.
(ITEM # EZM048)
NOTE:
Please remove the
clear plastic nozzle
when using EZP007 or
any of the Scoop-ItTM
Portion Wheels.
11. When not in use, fasten the PRO Fresh Lid onto the nozzle.
BASE

CARING FOR YOUR DISPENSER
1. To maintain the quality of your EZ-PRO™ dispenser, wash all parts daily in warm soapy water. Use a non-abrasive sponge.
2. DO NOT put any part of the unit through any dishwasher or dryer machines.
3. When disassembling the container, handle all parts gently. Please refrain from using too much force.
HOW TO DISASSEMBLE:
1. Remove the container from the stand by holding it securely and lifting directly upward, clearing the hooks from the
notches on the stand.
2. Remove lid from top of container. Make sure there is no remaining product inside that can spill over.
3. Remove handle clip at the back of the container.
4. Gently pull the handle from the front of the container. Set aside both handle and label holder.
5. Reach into container and remove portion wheel by gently pulling upwards or turning container upside down. Do the
same to remove the nozzle.
HOW TO ASSEMBLE:
1. Place nozzle into container, followed by the portion wheel.
3. Position the label holder so that it matches the hole on the front of the container.
5. Install handle clip to the back end of the shaft. Make sure it locks snugly into place.
6. Fill container with desired dry product and place lid securely on the container.
7. Follow steps 7 and 8 on Page 1.
*Other wheels available: 2, 3, 4.5 teaspoon portions
Please contact our customersupport at [phone] and we’ll be
happy to assist with any assemblyquestions, comments or concerns.
ROSSETO®3600 W. Pratt Avenue. Lincolnwood, IL 60712
Visitour website at: www.rosseto.com
NEEDASSISTANCE?
2. Adjust the portion wheel inside the container, so that its holes align with the container’s holes (both front and back).
4. Insert handle through the label holder and front hole. Push the shaft through the portion wheel, all the way to
the back of the container.
4. To keep the tray and base polished, use a commercial stainless steel surface cleaner.
5. Reassemble the unit only after all parts are completely dry.
CLEANING INSTRUCTIONS:
INTERCHANGEABLE PORTION WHEELS
Your new EZ-SERV® Dispenser comes with 3 easily interchangeable Portion Wheels delivering just the right amount of
product every time.
Here are some quick guidelines to explain how the different wheels work:
The 6W is great for dispensing bulk dry foods like cereals, coffee beans, loose tea;
snacks like granola & trail mix and M&M’s and most other candies.
The 6SM is perfect for medium sized or non-uniform foods like chopped cookies,
pie crust, cookie dough.
If you are looking for precision, the 1 tsp. Scoop-It™ wheel delivers consistent portions
over and over. The patent-pending Scoop-It™ wheels are ideal for the smallest items like
Jimmies/Sprinkles, chopped nuts and M&M’s®, mini Hershey’s Kisses® as well as Sugar,
powdered creamer and seasonings & spices.
Also available are 2 Tsp, 3 Tsp and 5 Tsp Scoop-It™ Wheels!
6W: 1 Oz.
6-Wing Wheel
ITEM #: EZP004
6SM: 1 Tbsp.
PRO6-SM
ITEM #: PRO6-SM
Scoop-It™: 1 Tsp
ITEM #: EZP007
2014 February 12 IS023 - V2