Rosslare AY-V12B User manual

AY-V12B
Multi-Reader
Installation Manual

Copyright © 2014 by Rosslare. All rights reserved.
This manual and the information contained herein are proprietary to ROSSLARE
ENTERPRISES LIMITED and/or its related companies and/or subsidiaries’
(hereafter: "ROSSLARE"). Only ROSSLARE and its customers have the right to
use the information.
No part of this manual may be re-produced or transmitted in any form or by any
means, electronic or mechanical, for any purpose, without the express written
permission of ROSSLARE.
ROSSLARE owns patents and patent applications, trademarks, copyrights, or
other intellectual property rights covering the subject matter in this manual.
TEXTS, IMAGES, AND ILLUSTRATIONS INCLUDING THEIR ARRANGEMENT IN
THIS DOCUMENT ARE SUBJECT TO THE PROTECTION OF COPYRIGHT LAWS
AND OTHER LEGAL RIGHTS WORLDWIDE. THEIR USE, REPRODUCTION, AND
TRANSMITTAL TO THIRD PARTIES WITHOUT EXPRESS WRITTEN PERMISSION
MAY RESULT IN LEGAL PROCEEDINGS.
The furnishing of this manual to any party does not give that party or any third
party any license to these patents, trademarks, copyrights or other intellectual
property rights, except as expressly provided in any written agreement of
ROSSLARE.
ROSSLARE reserves the right to revise and change this document at any time,
without being obliged to announce such revisions or changes beforehand or
after the fact.

Table of Contents
AY-V12B Installation Manual iii
Table of Contents
1. Introduction ................................................................7
2. Technical Specifications..............................................8
3. Installation ..................................................................9
3.1 Installation Kit......................................................................... 9
3.2 Installing the AY-V12B ............................................................ 9
4. Wiring Instructions ...................................................11
5. Operation Instructions..............................................12
A. Limited Warranty ......................................................13

List of Figures
iv AY-V12B Installation Manual
List of Figures
Figure 2: Removing the Top Cover ....................................................................9

List of Tables
AY-V12B Installation Manual v
List of Tables
Table 1: Wiring Colors .....................................................................................11

Notice and Disclaimer
vi AY-V12B Installation Manual
Notice and Disclaimer
This manual’s sole purpose is to assist installers and/or users in the safe and
efficient installation and usage of the system and/or product, and/or software
described herein.
BEFORE ATTEMPTING TO INSTALL AND/OR USE THE SYSTEM,THE INSTALLER AND THE
USER MUST READ THIS MANUAL AND BECOME FAMILIAR WITH ALL SAFETY
REQUIREMENTS AND OPERATING PROCEDURES.
The system must not be used for purposes other than those for which it
was designed.
The use of the software associated with the system and/or product, if
applicable, is subject to the terms of the license provided as part of the
purchase documents.
ROSSLARE exclusive warranty and liability is limited to the warranty and
liability statement provided in an appendix at the end of this document.
This manual describes the maximum configuration of the system with the
maximum number of functions, including future options. Therefore, not all
functions described in this manual may be available in the specific system
and/or product configuration you purchased.
Incorrect operation or installation, or failure of the user to effectively
maintain the system, relieves the manufacturer (and seller) from all or any
responsibility for consequent noncompliance, damage, or injury.
The text, images and graphics contained in the manual are for the purpose
of illustration and reference only.
All data contained herein subject to change without prior notice.
In no event shall manufacturer be liable for any special, direct, indirect,
incidental, consequential, exemplary or punitive damages (including,
without limitation, any and all damages from business interruption, loss of
profits or revenue, cost of capital or loss of use of any property or capital or
injury).
All graphics in this manual are for reference only, some deviation between
the image(s) and the actual product may occur.
All wiring diagrams are intended for reference only, the photograph or
graphic of the PCB(s) are intended for clearer illustration and
understanding of the product and may differ from the actual PCB(s).

Introduction
AY-V12B Installation Manual 7
1. Introduction
The AY-V12B Multi-Reader is an RFID proximity card reader, utilized
with access control systems. The reader is compatible with standard
and passive EM-type cards and tags, and features an output format of
standard Wiegand 26-Bit.
The reader also contains two LED indicators that show the unit’s
status upon power up and the status for card reading attempts.
This manual contains the following information:
Installation instructions
Wiring instructions
Operation instructions

Technical Specifications
8 AY-V12B Installation Manual
2. Technical Specifications
Electrical Characteristics
Power Supply Type Linear type (recommended)
Operating Voltage Range 5 to 16 VDC
Absolute Maximum
(non-operating)
18 VDC
Input Current Standby: 120 mA
Read: 140 mA
Tamper Output Open collector, active low, max. sink
current 30 mA
Maximum Cable Distance to
Controller
150 m (500 ft)
Card Output Format Wiegand 26-Bit
Max. Proximity Card Read
Range*
22 cm (9 in.)
Environmental Characteristics
Operating Temp. Range -32°C to 63°C (-25°F to 145°F)
Operating Humidity Range 0 to 95% (non-condensing)
Suitable for outdoor use (IP54)
Physical Characteristics
Dimensions (H x W x D) 125 x 125 x 21 mm
(4.9 x 4.9 x 0.8 in.)
Weight 285 g (10.1 oz)
* Measured using a Rosslare proximity card or equivalent. Range also depends
on electrical environment and proximity to metal.

Installation
AY-V12B Installation Manual 9
3. Installation
Installation of an RFID reader adjacent to metallic surfaces
might alter the reader’s specifications. To diminish this
interference, use a plastic spacer when mounting the reader.
3.1 Installation Kit
The installation kit comprises of the following items that are to be
used during the installation procedure:
One installation template
Two pan head screws and wall plugs
One L-shaped security screw tool
Two security screws
3.2 Installing the AY-V12B
When installing the reader, you must remove the snap-off cover to
access the screw holes (Figure 1).
Figure 1: Removing the Top Cover

Installation
10 AY-V12B Installation Manual
The reader must be mounted with the appropriate screws (not
supplied), as described in the template provided.
To install the reader:
1. Determine an approximate location for the installation of the
reader.
2. Peel off the back of the self-adhesive installation label template
and locate it at the required location.
3. Using the template as a guide, drill two holes (the size of which
are indicated in the template) to install the reader onto the
surface.
4. Drill a 10-mm (7/16”) hole for the cable. In the event that you are
installing the reader on metal, place a grommet or electrical tape
around the edge of the hole.
5. Route the interface cable from the reader to the controller. A
linear type power supply is recommended.
The reader can also be mounted using strong epoxy glue. After
application, the reader should be firmly held in place until the
glue dries.

Wiring Instructions
AY-V12B Installation Manual 11
4. Wiring Instructions
The AY-V12B is supplied with a 46-cm (18”) pigtail, comprising a 6-
conductor cable.
To connect the reader to the controller:
1. Prepare the reader cable by cutting the cable jacket back 3.2 cm
(1¼”) and stripping the wire 1.3 cm (½”).
2. Prepare the controller cable by cutting the cable jacket back 3.2
cm (1¼”) and stripping the wire 1.3 cm (½”).
3. Splice the reader’s pigtail wires to the corresponding controller
wires and cover each joint with insulating tape.
If the tamper output is being utilized, connect the purple wire to
the correct input on the controller.
Table 1: Wiring Colors
Reader Color Function
5~16 VDC Red DC Input
Shield/Ground Black Ground
Data 1 White Data 1
Data 0 Green Data 0
LEDCTLO Brown LED Control
Tamper Purple Tamper
4. Trim and cover all unused conductors.
•The individual wires from the reader are color-coded according the
Wiegand standard.
•When using a separate power supply for the reader, this supply and
that of the controller, must have a common ground.
•The reader’s cable shield wire should preferably be attached to an
earth ground, or a signal ground connection at the panel, or power
supply end of he cable. This configuration is best fro shielding the
Reader cable from external interference

Operation Instructions
12 AY-V12B Installation Manual
5. Operation Instructions
The reader should be tested after wiring it to a power supply and the
controller.
To test the reader:
1. Power up the reader. The red LED lights turn on. The beeper
sounds once.
2. Present the appropriate type of proximity card to the reader. The
LED momentarily flashes green and a short beep is emitted, thus
indicating that the card was read properly by the reader.
The reader transmits the card's data to the controller. The
controller checks the data and if it is valid, the LED changes
momentarily to green. It then returns to its idle state (red).

Limited Warranty
AY-V12B Installation Manual 13
A. Limited Warranty
The full ROSSLARE Limited Warranty Statement is available in the
Quick Links section on the ROSSLARE website at
www.rosslaresecurity.com.
Rosslare considers any use of this product as agreement to the
Warranty Terms even if you do not review them.

AY-V12B
Asia Pacific, Middle
East, Africa
Rosslare Enterprises Ltd.
Kowloon Bay, Hong Kong
Tel: [phone]
Fax: [phone]
[e-mail]
United States and
Canada
Rosslare Security Products, Inc.
Southlake, TX, USA
Toll Free: [phone]
Local: [phone]
Fax: [phone]
[e-mail]
Europe
Rosslare Israel Ltd.
Rosh HaAyin, Israel
Tel: [phone]
Fax: [phone]
[e-mail]
Latin America
Rosslare Latin America
Buenos Aires, Argentina
Tel: [phone]
[e-mail]
China
Rosslare Electronics (Shenzhen) Ltd.
Shenzhen, China
Tel: [phone]
Fax: [phone]
[e-mail]
India
Rosslare Electronics India Pvt Ltd.
Tel/Fax: [phone]
Mobile: [phone]
[e-mail]
0706-0960094+03