Rosslare MIFARE Classic AY-25B Series User manual

AY-x25B Series
MIFARE Classic® EV1 CSN Readers
Installation Manual
1
1. Introduction
The AY-x25B is a series of RFID proximity card readers to be
installed for use with access control systems.
The AY-x25B series reads the card serial number (CSN) from
MIFARE Classic® EV1 credentials (4 UID and 7 UID) and transmits
its data to the access control system using Wiegand 26-Bit output.
Other Wiegand formats and the Clock & Data format are available as
factory configurable options.
Figure 1: AY-x25B Series
AY-M25B AY-H25B AY-L25B AY-K25B
2. Technical Specifications
2.1 Electrical Characteristics
Specifications AY-M25B AY-H25B AY-L25B AY-K25B
Power Supply Type Linear (recommended)
Operating Voltage
Range
5–16 VDC
Absolute Maximum
(non-operating)
18 VDC
Current @ 12V Standby: 45 mA
Maximum: 100 mA
Max. Read Range* 6.5 cm
(2.6 in.)
7.0 cm
(2.8 in.)
6.0 cm
(2.4 in.)
LED Control Input Dry Contact, N.O.
Tamper Output Open collector, active low, max. sink current 16 mA
Maximum Cable
Distance to Controller
18-AWG: 150 m (500 ft)
20-AWG: 90 m (300 ft)
Frequency 13.56 MHz
Bit Rate 106 KHz
* Measured using a Rosslare MIFARE Classic EV1 card or equivalent. Range
also depends on installation environment, reader voltage, and proximity to
metal.
2.2 Environmental Characteristics
Specifications AY-M25B AY-H25B AY-L25B AY-K25B
Operating Temp.
Range
-31°C to 63°C (-25°F to 145°F)
Operating Humidity
Range
0 to 95% (non-condensing)
2.3 Physical Characteristics
Model Dimensions
(H x W x D)
Weight
AY-M25B 89 x 89 x 15 mm
(3.5 x 3.5 x 0.6 in.)
109.1 g
(3.8 oz.)
AY-H25B 110 x 75 x 15 mm
(4.3 x 3.0 x 0.6 in.)
116.9 g
(4.1 oz)
AY-L25B 145 x 43 x 20 mm
(5.7 x 1.7 x 0.8 in.)
111.1 g
(3.9 oz)
AY-K25B 80 x 40 x 12.8 mm
(3.2 x 1.6 x 0.5 in.)
68.5 g
(2.4 oz)
3. Installation
Installation of an RFID reader adjacent to metallic surfaces
might alter the reader’s specifications. To diminish this
interference, use a plastic spacer when mounting the reader.
3.1 Installation Kit
The installation kit consists of the following items to be used during
the installation procedure:
One self-adhesive mounting label template
Two pan head mounting screws and screw anchors
One Torx key tool
One Torx security screw
3.2 Mounting
Before mounting, you should determine the best location for the
reader.
To mount the reader:
1. Peel off the back of the self-adhesive mounting label template
and place it at the required mounting location.
2. Using the template as a guide, drill two holes (hole size and
position is indicated on the mounting template) for mounting the
reader onto the surface.
3. Insert a screw anchor into each hole.
4. Drill a 10-mm (7/16”) hole for the cable. If mounting on metal,
place a grommet or electrical tape around the edge of the hole.
5. Remove the screw from the bottom of the unit.
6. Remove the reader's snap-off front cover.
7. Insert the unit’s cable wire into the cable hole and wire the unit
as described in Section 3.3. A linear type power supply is
recommended.
8. Align the two holes of the reader with those drilled in the wall
and firmly attach the reader to the wall with two screws (Figure
2).
Figure 2: Inserting Mounting Screws
9. Relocate the front cover onto the reader.
10. Secure the front cover by using the supplied security Torx screw.
A Torx security screw tool is provided to tighten the security
Torx screw.

2 0706-
0960191+04
3.3 Wiring
The AY-x25B is supplied with a 6-conductor 56-cm (22-in.) pigtail
with exposed wires coated with solder.
To connect the reader to the controller:
1. Select the appropriate connections according to Table 1.
Table 1: Wiring
Wire Color Function
Red VIN 5–16 VDC
Black Shield / Ground
Green
Data 0 / Data
White Data 1 / Clock
Brown Green LED CTL
Purple Tamper Output
2. Prepare the controller cable by cutting its jacket back 3 cm (1¼")
and strip the insulation from the wires about 1.2 cm (½").
3. Splice the reader’s pigtail wires to the corresponding controller
wires and cover each joint with insulating tape.
4. If the tamper output is being utilized, connect the purple wire to
the correct input on the controller.
5. Trim and cover all unused conductors.
•When using a separate power supply for the reader, this supply
and that of the controller must have a common ground.
•The reader’s cable shield wire should be preferably attached to
an earth ground, or a signal ground connection at the panel, or
power supply end of the cable. This configuration is best for
shielding the reader cable from external interference.
3.4 Operation Instructions
Once the reader is wired to a power supply and to the controller, you
should test the reader.
To test the reader:
1. Power up the reader.
Upon power up, the reader flashes and beeps once during Self-
Test. The LED then turns red indicating the readers has entered
Standby mode.
2. Apply a MIFARE Classic EV1 credential to the reader.
The reader flashes and beeps once indicating the card has been
read successfully.
Declaration of Conformity
FCC ID = GCD-AYX25B
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
Limited Warranty
The full ROSSLARE Limited Warranty Statement is available in the
Quick Links section on the ROSSLARE website at
www.rosslaresecurity.com.
Rosslare considers any use of this product as agreement to the
Warranty Terms even if you do not review them.
Contact Information
United States and Canada
Rosslare Security Products, Inc.
Southlake, TX, USA
Toll Free: [phone]
Local: [phone]
Fax: [phone]
[e-mail]
Europe
Rosslare Israel Ltd.
22 Ha'Melacha St., P.O.B. 11407
Rosh HaAyin, Israel
Tel: [phone]
Fax: [phone]
[e-mail]
China
Rosslare Electronics (Shenzhen) Ltd.
Shenzhen, China
Tel: [phone]
Fax: [phone]
[e-mail]
Asia Pacific, Middle East, Africa
Rosslare Enterprises Ltd.
Kowloon Bay, Hong Kong
Tel: [phone]
Fax: [phone]
[e-mail]
Latin America
Rosslare Latin America
Buenos Aires, Argentina
[e-mail]
India
Rosslare Electronics India Pvt Ltd.
Tel/Fax: [phone]
Mobile: [phone]
[e-mail]
CERT
ISO 9001
ISO 14001