Rosslare Anti-Vandal MIFARE AY-Q6 60 Series User manual

AY-Q6x60 Series
Anti-Vandal MIFARE® Contactless
Smart Card / Sector Readers
Installation and User Manual
Models:
AY-Q6260
AY-Q6360
AY-Q6260 AY-Q6360

Copyright © 2019 by Rosslare. All rights reserved.
This manual and the information contained herein are proprietary to
ROSSLARE ENTERPRISES LIMITED and/or its related companies and/or
subsidiaries’ (hereafter: "ROSSLARE"). Only ROSSLARE and its customers
have the right to use the information.
No part of this manual may be re-produced or transmitted in any form or by
any means, electronic or mechanical, for any purpose, without the express
written permission of ROSSLARE.
ROSSLARE owns patents and patent applications, trademarks, copyrights, or
other intellectual property rights covering the subject matter in this manual.
TEXTS, IMAGES, AND ILLUSTRATIONS INCLUDING THEIR ARRANGEMENT IN
THIS DOCUMENT ARE SUBJECT TO THE PROTECTION OF COPYRIGHT
LAWS AND OTHER LEGAL RIGHTS WORLDWIDE. THEIR USE,
REPRODUCTION, AND TRANSMITTAL TO THIRD PARTIES WITHOUT
EXPRESS WRITTEN PERMISSION MAY RESULT IN LEGAL PROCEEDINGS.
The furnishing of this manual to any party does not give that party or any
third party any license to these patents, trademarks, copyrights or other
intellectual property rights, except as expressly provided in any written
agreement of ROSSLARE.
ROSSLARE reserves the right to revise and change this document at any time,
without being obliged to announce such revisions or changes beforehand or
after the fact.

Table of Contents
AY-Q6x60 Series Installation and Programming Manual iii
Table of Contents
1. Introduction...........................................................................8
1.1 Supported RFID Transponders .................................................. 9
1.2 Box Content ............................................................................... 9
2. Installation ..........................................................................10
2.1 Mounting.................................................................................. 10
2.2 Wiring....................................................................................... 11
3. Configuring the Reader .......................................................13
3.1 Operation Modes ..................................................................... 13
3.2 Configuration Card Structure................................................... 14
3.3 Configuring Settings................................................................ 14
3.4 Configuration Procedure ......................................................... 15
4. How to Use the Reader ........................................................16
4.1 Normal Operation .................................................................... 16
4.1.1 Card Serial Number Mode ...............................................................16
4.1.2 Secure Mode.....................................................................................16
4.2 Manual LED and Buzzer Control.............................................. 17
4.3 Optical Back Tamper ............................................................... 18
5. Programming ......................................................................19
5.1 Standby Mode.......................................................................... 19
5.2 Programming Menu................................................................. 19
5.3 Entering Programming Mode .................................................. 21
5.4 Exiting Programming Mode..................................................... 21
5.5 Selecting Keypad Transmission Format ................................. 22

Table of Contents
iv AY-Q6x60 Series Installation and Programming Manual
5.5.1 Keypad Transmission Formats.......................................................23
5.6 Selecting Proximity Card Transmission Format ..................... 28
5.6.1 Proximity Card Transmission Formats ..........................................29
5.7 Changing the Programming Code........................................... 32
5.8 Changing the Facility Code...................................................... 32
5.9 Setting the Backlight Behavior ................................................ 33
5.10 Return to Factory Default Settings .......................................... 33
5.11 Replacing a lost Programming Code....................................... 34
6. Technical Specifications .....................................................35
A. Limited Warranty.................................................................37

List of Figures
AY-Q6x60 Series Installation and Programming Manual v
List of Figures
Figure 1: Drilling Mounting Holes .......................................................................10

List of Tables
vi AY-Q6x60 Series Installation and Programming Manual
List of Tables
Table 1: Wiring the Reader to the Controller......................................................11
Table 2: Programming Menu ..............................................................................20

Notice and Disclaimer
AY-Q6x60 Series Installation and Programming Manual vii
Notice and Disclaimer
This manual’s sole purpose is to assist installers and/or users in the safe and
efficient installation and usage of the system and/or product, and/or
software described herein.
BEFORE ATTEMPTING TO INSTALL AND/OR USE THE SYSTEM,THE INSTALLER AND THE
USER MUST READ THIS MANUAL AND BECOME FAMILIAR WITH ALL SAFETY REQUIREMENTS
AND OPERATING PROCEDURES.
The system must not be used for purposes other than those for which it
was designed.
The use of the software associated with the system and/or product, if
applicable, is subject to the terms of the license provided as part of the
purchase documents.
ROSSLARE exclusive warranty and liability is limited to the warranty and
liability statement provided in an appendix at the end of this document.
This manual describes the maximum configuration of the system with
the maximum number of functions, including future options. Therefore,
not all functions described in this manual may be available in the
specific system and/or product configuration you purchased.
Incorrect operation or installation, or failure of the user to effectively
maintain the system, relieves the manufacturer (and seller) from all or
any responsibility for consequent noncompliance, damage, or injury.
The text, images and graphics contained in the manual are for the
purpose of illustration and reference only.
All data contained herein subject to change without prior notice.
In no event shall manufacturer be liable for any special, direct, indirect,
incidental, consequential, exemplary or punitive damages (including,
without limitation, any and all damages from business interruption, loss
of profits or revenue, cost of capital or loss of use of any property or
capital or injury).
All wiring diagrams are intended for reference only, the photograph or
graphic of the PCB(s) are intended for clearer illustration and
understanding of the product and may differ from the actual PCB(s).

Introduction
8 AY-Q6x60 Series Installation and Programming Manual
1. Introduction
The AY-Q6260 and AY-Q6360 are metallic, anti-vandal, MIFARE®
contactless smart card sector readers used in access control
system solutions.
The readers scan information from a MIFARE smart card, which is
stored in a specific and protected sector, and send the data on to a
connected access control system.
The system reads MIFARE 1K and MIFARE 4K card sector data, as
well as the unique ID number of the following cards: MIFARE 1K,
MIFARE 4K, MIFARE Ultralight, and MIFARE DESFire. The readers
transmit the identification numbers they receive to an access
control system.
The readers can also check the validity of cards before scanning
them. When checking, readers only send card information to the
access control system from cards with the correct security pass-
code. The readers are suitable for both indoor and outdoor
installations.
Reader setup and operation is controlled using a configuration card
to adjust settings directly, without having to connect a remote
computer or remove the unit. The configuration card is a regular
MIFARE 1K card, which can be pre-programmed using Rosslare’s
CP-R25 (or CP-R26) desktop MIFARE programmer, together with its
associated software the AS-B01.
The AY-Q6260 and AY-Q6360 readers are compatible with almost
all access controllers, including Rosslare's AC-115, AC-215, and
AC-225 controllers.

Introduction
AY-Q6x60 Series Installation and Programming Manual 9
1.1 Supported RFID Transponders
The AY-Q6260 and AY-Q6360 read the following transponders:
MIFARE Ultralight (card serial number only)
MIFARE Classic 1K
MIFARE 4K
MIFARE DESFire (card serial number only)
1.2 Box Content
Before beginning, verify that all of the following is in the box. If
anything is missing, please report the discrepancy to your nearest
Rosslare office.
1reader
1 manual
Installation kit including:
1 self-adhesive drilling template
1 security spline key
1 security hex key
2 mounting screws
2 wall plugs

Installation
10 AY-Q6x60 Series Installation and Programming Manual
2. Installation
Installation of an RFID reader adjacent to metallic surfaces
might alter the reader’s specifications. To diminish this
interference, use a plastic spacer when mounting the reader.
2.1 Mounting
Before starting, select the location to mount the unit. This location
should be at shoulder height.
To mount the unit:
1. Peel off the back of the self-adhesive installation template and
attach the template to the required location.
2. At the bottom of the unit’s case, remove the screw.
3. Remove the cover by gently sliding it up and then pulling it
apart. Once you remove the cover, you will see the screw holes
for mounting.
4. Depending on the type of installation, gang box or panel mount,
drill the respective holes in the rear cover: for gang box
mounting, drill two holes marked “A”; for flat panel mount, drill
four holes marked “B” (Figure 1).
Figure 1: Drilling Mounting Holes