Rosslare MIFARE Classic AY-K6255 User manual

AY-K6255
MIFARE Classic CSN Smart Card Reader (Rev. A)
Installation and User Manual
1
1. Introduction
The AY-K6255 is a contactless smart card reader for use in access
control system solutions. This reader reads the Card Serial Number
(CSN) of MIFARE Classic® EV1 (ISO14443A) credentials.
The standard readers output the Wiegand CSN data in 26-bit format.
Other Wiegand formats are available upon request.
The reader is approved by the Institute for Science and Halacha for use
on the Sabbath.
Figure 1: AY-K6255
2. Technical Specifications
2.1 Electrical Characteristics
Power Supply Type Regulated
Operating Voltage Range 8 to 16 VDC
Current @ 12 V Standby: 55 mA, max: 80 mA
Read Range* 5 cm (2.0 in.)
LED/Buzzer Controls** Dry Contact, N.O.
Tamper Output** Open collector, active low, max. sink current
16 mA
Maximum Cable Distance
to Controller
Wiegand: 150 m (500 ft) with 18-AWG cable
OSDP (RS-485): 1,200 m (4,000 ft) with 2x2
18-AWG twisted shielded cable
* Measured using a Rosslare MIFARE Classic EV1 (ISO card). Read range with
other credential technologies may vary. Range also depends on electrical
environment and proximity to metal.
** Control lines are factory programmable and can be custom configured upon
request.
2.2 Environmental Characteristics
Operating Temp. Range -35°C to 66°C (-31°F to 150°F)
Operating Humidity Range 0 to 95% (non-condensing)
Outdoor Usage Weather-resistant, UV-resistant, meets IP65,
epoxy-potted, suitable for indoor and outdoor
use
2.3 Physical Characteristics
Dimensions (H x W x D) 80.5 x 40.5 x 14.7 mm (3.2 x 1.6 x 0.6in.)
Weight 73 g (2.6 oz)
3. Installation
3.1 Installation Kit
The installation kit consists of the following items to be used during
the installation procedure:
1 backplate
1 self-adhesive mounting label template
1 metal clip
2 pan head mounting screws and screw anchors
1 Torx key tool and one Torx security screw
3.2 Mounting
Before mounting, you should determine the best location for the
reader.
To mount the reader:
1. Peel off the back of the self-adhesive mounting label template and
place it at the required mounting location.
2. Using the template as a guide, drill two holes (hole size and
position is indicated on the mounting template) for mounting the
reader onto the surface.
3. Insert a screw anchor into each hole.
4. Drill a 10-mm (7/16”) hole for the cable. If mounting on metal,
place a grommet or electrical tape around the edge of the hole.
5. Wire the reader to the host as described in Section 3.3. A linear
type power supply is recommended.
6. Remove the security screw from the bottom of the unit.
7. Remove the reader's snap-off front cover.
8. Align the two holes of the backplate and of the reader with those
drilled in the wall and firmly attach the reader to the wall with two
screws (Figure 2).
Figure 2: Mounting Screws
9. Relocate the front cover onto the reader.
10. Return the security screw to the bottom of the unit.
11. Insert the metal clip into the slot at the base of the backplate
(Figure 3).
Figure 3: Metal Clip

2
3.3 Wiring
The AY-K6255 is supplied with a 10-conductor 56-cm (22-in.) pigtail
with exposed wires coated with solder.
To connect the reader to the controller:
1. Select the appropriate connections according to Table 1.
2. Prepare the controller cable by cutting its jacket back 3 cm (1¼")
and strip the insulation from the wires about 1.2 cm (½").
3. Splice the reader’s pigtail wires to the corresponding controller
wires and cover each joint with insulating tape.
4. If the tamper output is being utilized, connect the purple wire to
the correct input on the controller.
5. Trim and cover all unused conductors.
•The individual wires from the reader are color coded according the
Wiegand standard.
•When using a separate power supply for the reader, this supply and
that of the controller must have a common ground.
•The reader’s cable shield wire should be preferably attached to an
earth ground, or a signal ground connection at the panel, or the
power supply end of the cable.
Table 1: Wiring
Wire Color Function
Red Power
Black Ground
Green Data 0 / Data
White Data 1 / Clock
Orange Green LED control
Brown Red LED control
Purple Tamper output
Yellow Sabbath (Buzzer)
Blue RS-485 – A*
Gray RS-485 – B*
* RS-485 is used for firmware update.
4. Sabbath Mode
To activate the Sabbath mode, the yellow wire must be connected to
ground.
When in this mode, the reader behaves as follows:
The reader is off for 4 seconds.
While the reader is off, the user can present a card.
The reader wakes up for 200 ms.
To de-activate the Sabbath mode, the yellow wire must be
disconnected.

3
Declaration of Conformity
AY-K6255SH: FCC ID = GCD-AYX6255
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Limited Warranty
The full ROSSLARE Limited Warranty Statement is available in the Quick Links section on the ROSSLARE website at www.rosslaresecurity.com.
Rosslare considers any use of this product as agreement to the Warranty Terms even if you do not review them.
Contact Information
United States and Canada
Rosslare Security Products, Inc.
Southlake, TX, USA
Toll Free: [phone]
Local: [phone]
Fax: [phone]
[e-mail]
Europe
Rosslare Israel Ltd.
Rosh HaAyin, Israel
Tel: [phone]
Fax: [phone]
[e-mail]
Latin America
Rosslare Latin America
Buenos Aires, Argentina
Tel: [phone]
[e-mail]
China
Rosslare Electronics (Shenzhen) Ltd.
Shenzhen, China
Tel: [phone]
Fax: [phone]
[e-mail]
Asia Pacific, Middle East, Africa
Rosslare Enterprises Ltd.
Kowloon Bay, Hong Kong
Tel: [phone]
Fax: [phone]
[e-mail]
India
Rosslare Electronics India Pvt Ltd.
Tel/Fax: [phone]
Mobile: [phone]
[e-mail]
CERT
ISO 9001
ISO 14001
0706-0960638+00