Rosslare MIFARE AY-T6350 Assembly instructions

AY-T6350
MIFARE® Contactless Smart Card / PIN
Readers
Installation and Programming Manual

Copyright © 2018 by Rosslare. All rights reserved.
This manual and the information contained herein are proprietary to ROSSLARE
ENTERPRISES LIMITED and/or its related companies and/or subsidiaries’
(hereafter: "ROSSLARE"). Only ROSSLARE and its customers have the right to
use the information.
No part of this manual may be re-produced or transmitted in any form or by any
means, electronic or mechanical, for any purpose, without the express written
permission of ROSSLARE.
ROSSLARE owns patents and patent applications, trademarks, copyrights, or
other intellectual property rights covering the subject matter in this manual.
TEXTS, IMAGES, AND ILLUSTRATIONS INCLUDING THEIR ARRANGEMENT IN
THIS DOCUMENT ARE SUBJECT TO THE PROTECTION OF COPYRIGHT LAWS
AND OTHER LEGAL RIGHTS WORLDWIDE. THEIR USE, REPRODUCTION, AND
TRANSMITTAL TO THIRD PARTIES WITHOUT EXPRESS WRITTEN PERMISSION
MAY RESULT IN LEGAL PROCEEDINGS.
The furnishing of this manual to any party does not give that party or any third
party any license to these patents, trademarks, copyrights or other intellectual
property rights, except as expressly provided in any written agreement of
ROSSLARE.
ROSSLARE reserves the right to revise and change this document at any time,
without being obliged to announce such revisions or changes beforehand or
after the fact.

Table of Contents
AY-T6350 Installation and Programming Manual iii
Table of Contents
1. Introduction ................................................................8
1.1 Supported RFID Transponders.................................................. 8
1.2 Box Content ........................................................................... 8
2. Technical Specifications..............................................9
3. Installation ................................................................10
3.1 Mounting ............................................................................. 10
3.2 Wiring .................................................................................. 11
4. How to Use the Reader .............................................13
4.1 Normal Operation ................................................................. 13
4.2 Optical Back Tamper ............................................................. 14
4.3 LED Control .......................................................................... 14
5. Keypad Programming Instructions ..........................15
5.1 Programming Menu .............................................................. 15
5.2 Entering Programming Mode................................................. 16
5.3 Exiting Programming Mode ................................................... 16
5.4 Selecting Keypad Transmission Format ................................... 17
5.4.1 Single Key, Wiegand 6-Bit (Rosslare Format) .................................18
5.4.2 Single Key, Wiegand 6-Bit, Nibble & Parities .................................18
5.4.3 Single Key, Wiegand 8-Bit, Nibbles Complemented ......................18
5.4.4 4 Keys Binary + Facility Code, Wiegand 26-Bit ..............................19
5.4.5 1 to 5 Keys + Facility Code, Wiegand 26-Bit .................................19
5.4.6 6 Keys BCD and Parity Bits, Wiegand 26-Bit..................................20
5.4.7 Single Key, 3x4 Matrix Keypad (MD-P64)......................................21
5.4.8 1 to 8 Keys BCD, Clock & Data .....................................................21

Table of Contents
iv AY-T6350 Installation and Programming Manual
5.5 Selecting the Proximity Card Transmission Format................... 22
5.5.1 Wiegand 26-Bit ............................................................................23
5.5.2 Clock and Data.............................................................................23
5.5.3 Wiegand Card + PIN Transmission Format ....................................23
5.5.4 Wiegand 26-Bit and Facility Code .................................................24
5.5.5 Wiegand 32-Bit ............................................................................24
5.5.6 Wiegand 32-Bit Reversed..............................................................24
5.5.7 Wiegand 34-Bit ............................................................................25
5.5.8 Wiegand 40-Bit and Checksum ....................................................25
5.6 Changing the Programming Code.......................................... 26
5.7 Changing the Facility Code.................................................... 26
5.8 Return to Factory Default Settings.......................................... 27
5.9 Replacing a lost Programming Code....................................... 27
A. Limited Warranty ......................................................28

List of Figures
AY-T6350 Installation and Programming Manual v
List of Figures
Figure 1: Removing the Top Cover ..................................................................10

List of Tables
vi AY-T6350 Installation and Programming Manual
List of Tables
Table 1: Wiring Colors .....................................................................................11
Table 2: Programming Menu...........................................................................15

Notice and Disclaimer
AY-T6350 Installation and Programming Manual vii
Notice and Disclaimer
This manual’s sole purpose is to assist installers and/or users in the safe and
efficient installation and usage of the system and/or product, and/or software
described herein.
BEFORE ATTEMPTING TO INSTALL AND/OR USE THE SYSTEM,THE INSTALLER AND THE
USER MUST READ THIS MANUAL AND BECOME FAMILIAR WITH ALL SAFETY
REQUIREMENTS AND OPERATING PROCEDURES.
The system must not be used for purposes other than those for which it
was designed.
The use of the software associated with the system and/or product, if
applicable, is subject to the terms of the license provided as part of the
purchase documents.
ROSSLARE exclusive warranty and liability is limited to the warranty and
liability statement provided in an appendix at the end of this document.
This manual describes the maximum configuration of the system with the
maximum number of functions, including future options. Therefore, not all
functions described in this manual may be available in the specific system
and/or product configuration you purchased.
Incorrect operation or installation, or failure of the user to effectively
maintain the system, relieves the manufacturer (and seller) from all or any
responsibility for consequent noncompliance, damage, or injury.
The text, images and graphics contained in the manual are for the purpose
of illustration and reference only.
All data contained herein subject to change without prior notice.
In no event shall manufacturer be liable for any special, direct, indirect,
incidental, consequential, exemplary or punitive damages (including,
without limitation, any and all damages from business interruption, loss of
profits or revenue, cost of capital or loss of use of any property or capital or
injury).
All graphics in this manual are for reference only, some deviation between
the image(s) and the actual product may occur.
All wiring diagrams are intended for reference only, the photograph or
graphic of the PCB(s) are intended for clearer illustration and
understanding of the product and may differ from the actual PCB(s).

Introduction
8 AY-T6350 Installation and Programming Manual
1. Introduction
The AY-T6350 is MIFARE® contactless smart card and PIN reader for
indoor and outdoor use. The unit reads the MIFARE card serial
number (CSN) and transmits in Wiegand, Clock & Data, or Wiegand
Card + PIN formats.
In addition, the AY-T6350 comes with a backlit keypad that can be
programmed to output eight data formats. The AY-T6350 supports
MIFARE Classic and MIFARE Ultralight cards that allow multiple card
and keypad transmission formats, thus providing a high level of
compatibility and connectivity with host controllers.
1.1 Supported RFID Transponders
The AY-T6350 reads the following transponders:
MIFARE Ultralight 512-bit EEPROM
MIFARE Classic 1K bytes memory
MIFARE Classic 4K bytes memory
MIFARE Ultralight 512-bit EEPROM is only partly supported; only
32 bits out of the 64 bits can be transmitted.
1.2 Box Content
Before beginning, verify that all of the following is in the box; if
anything is missing, please contact your nearest Rosslare office.
One AY-T6350 reader
Installation kit including:
One drilling template (label/sticker)
One security spline key
One security hex screw
Two mounting screws and wall plugs
Installation and Programming Manual

Technical Specifications
AY-T6350 Installation and Programming Manual 9
2. Technical Specifications
Electrical Characteristics
Power Supply Type Linear (recommended)
Input Voltage 8–16 VDC
Absolute Maximum Voltage
(non-operating)
18 VDC
Maximum Input Current Standby: 180 mA, Read: 235 mA
LED Control Input Dry Contact N.O.
Tamper Output Open collector, active low, max. sink
current 32 mA
Max. Controller Cable Distance 150 m (500 ft)
Max. Proximity Read Range* 70 mm (2.8 in.)
Frequency 13.56 MHz
Transmission Formats Wiegand and Clock & Data
Card Compatibility MIFARE Classic and MIFARE Ultralight
cards
Environmental Characteristics
Operating Temp. Range -31°C to 63°C (-25°F to 145°F)
Operating Humidity 0 to 95% (non-condensing)
Suitable for outdoor use (meets IP65)
Physical Characteristics
Height x Width x Depth 110 x 80 x 17.5 mm (4.3 x 3.2 x 0.7 in.)
Weight 170 g (6 oz)
* Measured using a Rosslare proximity card or equivalent. Range also depends
on electrical environment and proximity to metal.

Installation
10 AY-T6350 Installation and Programming Manual
3. Installation
Installation of an RFID reader adjacent to metallic surfaces
might alter the reader’s specifications. To diminish this
interference, use a plastic spacer when mounting the reader.
The AY-T6350 pack includes everything needed to install and operate
the smart card sector readers. Mount the reader on the required
surface and connect it to the access control system.
3.1 Mounting
1. Peel off the back of the self-adhesive mounting label template
and place it at the required mounting location.
2. Using the template as a guide, drill two holes (sizes indicated on
the template) used for mounting the back plate onto the surface.
3. Insert a suitable wall plug into each screw hole.
4. Drill a 10-mm (7/16”) hole for the cable. If mounting on metal,
place a grommet or electrical tape around the edge of the hole.
5. At the bottom of the unit’s case, remove the screw.
6. Remove the reader's snap-off front cover to reveal the two screw
holes (Figure 1).
Figure 1: Removing the Top Cover

Installation
AY-T6350 Installation and Programming Manual 11
7. Insert the unit’s cable wire into the cable hole and wire the unit
as described in Section 3.2.
8. Screw the back cover to its mounting location.
9. Carefully re-attach the front cover of the unit.
10. Secure the front cover by using the supplied security Torx screw.
A Torx security screw tool is provided to tighten the security Torx
screw.
The reader can also be mounted using strong epoxy glue. After
application, the reader should be firmly held in place until the
glue dries.
3.2 Wiring
The reader is supplied with an 18” pigtail, comprising six wires.
To connect the reader to the controller:
1. Prepare the unit's cable by cutting the cable jacket back 3.2 cm
(1¼”) and stripping the wire 1.3 cm (½”).
2. Prepare the controller cable by cutting the cable jacket back 3.2
cm (1¼”) and stripping the wire 1.3 cm (½”).
3. Splice the reader’s pigtail wires to the corresponding controller
wires (as listed in Table 1) and cover each joint with insulating
tape.
Table 1: Wiring Colors
Reader Color Function
5~16 VDC Red +DC input
Shield/Ground Black Ground
Data 1 White Data 1
Data 0 Green Data 0
LEDCTL Brown LED/buzzer control
Tamper Purple Tamper

Installation
12 AY-T6350 Installation and Programming Manual
4. If the tamper output is being utilized, connect the purple wire to
the correct input on the controller.
5. Trim and cover all unused conductors.
•The individual wires from the reader are color-coded according the
Wiegand standard.
•When using a separate power supply for the reader, this supply and
that of the controller must have a common ground.
•The reader’s cable shield wire should be preferably attached to an
earth ground, or a signal ground connection at the panel, or a
power supply end of the cable. This configuration is best for
shielding the reader cable from external interference.

How to Use the Reader
AY-T6350 Installation and Programming Manual 13
4. How to Use the Reader
After the reader has been mounted, connected to an access control
system, and configured, it is ready for use.
4.1 Normal Operation
The default mode of the reader is Standby mode. In Standby mode,
the unit is ready to receive data from a presented proximity card or an
entered PIN code. When a card is presented, the reader scans the card
and sends each card's serial number to the access control system. This
CSN is unique for each card.
If the CSN is not fully transmitted, only the LSB portion of the
serial number is transmitted. This depends on the reader
transmit format of the selected reader and the length of the
CSN. For example, when the Wiegand 26-bit transmit format is
selected; the MSB byte of the MIFARE 1K card’s serial number is
not transmitted.
Programming the readeris done via the unit's keypad driven
programming menu system (Chapter 5).
Keyboard data can be sent via one of several different keypad
transmission formats (see Section 5.4).
MIFARE cards presented to the reader are always sent in Wiegand,
Clock & Data, or Card + PIN Wiegand format (see Section 5.5).
When the reader is in Standby mode, the LED is
white.
When a card or PIN entry is being transmitted, the
LED flashes green.
When the reader is in Programming mode, the LED is
off.

How to Use the Reader
14 AY-T6350 Installation and Programming Manual
4.2 Optical Back Tamper
The reader includes an optical back tampering mechanism which
detects all attempts to dismantle the unit or remove it from the wall.
The status of the tamper mechanism is indicated by the purple
Tamper control wire.
When the back tamper optical sensor is in “darkness” status, the
internal tamper output transistor is pulled to low.
When the back tamper optical sensor is in its "lit" status, the internal
tamper output transistor's collector is open. A tamper signal is
detected by the host control panel.
4.3 LED Control
To cause the LED to remain green continuously, pull the LED control
wire (brown) to ground (black wire). If the LED control wire (brown) is
left open, the LED behaves as described above.
Connecting the LED control input to the access control unit’s LED
control output allows control of the LED color; for example, it may
turn it green then back to white on access granted by a valid card.

Keypad Programming Instructions
AY-T6350 Installation and Programming Manual 15
5. Keypad Programming Instructions
5.1 Programming Menu
Programming the reader is done via the unit's keypad driven
programming menu system. Table 2 shows the names of all the
programming menus. Default factory settings (certain pre-
programmed codes and settings) are marked by an asterisk (*).
Table 2: Programming Menu
Menu Description Default
1 Selecting Keypad Transmission Format
1 – Single Key, Wiegand 6-Bit (Rosslare Format, Default)
2 – Single Key, Wiegand 6-Bit with Nibble + Parity Bits
3 – Single Key, Wiegand 8-Bit, Nibbles Complemented
4 – 4 Keys Binary + Facility Code, Wiegand 26-Bit
5 – 1 to 5 Keys + Facility Code, Wiegand 26-Bit
6 – 6 Keys BCD and Parity Bits, Wiegand 26-Bit
7 – Single Key, 3x4 Matrix Keypad
8 – 1 to 8 Keys BCD, Clock & Data Single Key
*
2 Selecting MIFARE Card Transmission Format
1 – Wiegand 26-Bit (default)
2 – Clock & Data
3 – Wiegand Card + PIN
4 – Wiegand 26-Bit with Facility Code Output
5 – Wiegand 32-Bit
6 – Wiegand 32-Bit Reverse Output
7 – Wiegand 34-Bit
8 – Wiegand 40-Bit
*
3 Changing the Programming Code 1234
4 Changing the Facility Code 001
0 Return to Factory Default Settings

Keypad Programming Instructions
16 AY-T6350 Installation and Programming Manual
5.2 Entering Programming Mode
To reach the Programming Menu System, the unit must first be
placed into Programming mode.
•The factory default Programming code is 1234.
•If a Programming code is not entered within 30 seconds, the reader
returns to Transmit mode.
To enter Programming mode:
1. Press #four times.
The LED flashes white.
2. Enter your 4-digit Programming code.
3. If the Programming code is valid, the program
LED turns off and the reader enters Programming
mode.
Wrong entries may reset the reader back to Standby mode. If no
key is pressed for 30 seconds while in Programming mode, the
unit exits Programming mode and returns to Standby mode
5.3 Exiting Programming Mode
To exit Programming mode:
1. Press #to exit Programming mode at any time.
You hear a long beep and the LED turns white.
This indicates that the unit has returned to Standby mode.

Keypad Programming Instructions
AY-T6350 Installation and Programming Manual 17
5.4 Selecting Keypad Transmission Format
There are eight keypad transmission formats.
Only one keypad transmission format can be active at any one
time.
To select the keypad transmission format:
1. Enter Programming mode.
2. Press 1 to enter Menu 1.
The LED flashes green.
3. Enter one of the following codes:
1– Single Key, Wiegand 6-Bit (Rosslare Format) (default)
2– Single Key, Wiegand 6-Bit with Nibble + Parity Bits
3– Single Key, Wiegand 8-Bit, Nibbles Complemented
4– 4 Keys Binary + Facility Code, Wiegand 26-Bit
5– 1 to 5 Keys + Facility Code, Wiegand 26-Bit
6– 6 Keys BCD and Parity Bits, Wiegand 26-Bit
7– Single Key, 3x4 Matrix Keypad
8– 1 to 8 Keys BCD, Clock & Data Single Key
9 – Single Key, Wiegand 4-Bit
When selecting Option 8, the Program LED turns green,
awaiting an additional key input to select the number of keys.
You hear three beeps.
The system returns to Standby mode.
If an incorrect option number is entered,
a long beep is heard and
the reader returns to Standby mode. The keypad transmission
format remains unchanged.

Keypad Programming Instructions
18 AY-T6350 Installation and Programming Manual
5.4.1 Single Key, Wiegand 6-Bit (Rosslare Format)
Each key press immediately sends 4 bits with 2 parity bits added –
even parity for the first 3 bits and odd parity for the last 3 bits.
0 = 1 1010 0 6 = 1 0110 0
1 = 0 0001 0 7 = 1 0111 1
2 = 0 0010 0 8 = 1 1000 1
3 = 0 0011 1 9 = 1 1001 0
4 = 1 0100 1 * = 1 1011 1 = "B" in Hexadecimal
5 = 1 0101 0 # = 0 1100 1 = "C" in Hexadecimal
5.4.2 Single Key, Wiegand 6-Bit, Nibble & Parities
Each key press immediately sends 4 bits with 2 parity bits added –
even parity for the first 3 bits and odd parity for the last 3 bits.
0 = 0 0000 1 6 = 1 0110 0
1 = 0 0001 0 7 = 1 0111 1
2 = 0 0010 0 8 = 1 1000 1
3 = 0 0011 1 9 = 1 1001 0
4 = 1 0100 1 * = 1 1010 0 = "A" in Hexadecimal
5 = 1 0101 0 # = 1 1011 1 = "B" in Hexadecimal
5.4.3 Single Key, Wiegand 8-Bit, Nibbles
Complemented
This options inverts the most significant bits in the message leaving
the least 4 significant bits as BCD representation of the key. The host
system receives an 8-bit message.
0 = 11110000 6 = 10010110
1 = 11100001 7 = 10000111
2 = 11010010 8 = 01111000
3 = 11000011 9 = 01101001
4 = 10110100 *= 01011010 = "A" in Hexadecimal
5 = 10100101 # = 01001011 = "B" in Hexadecimal

Keypad Programming Instructions
AY-T6350 Installation and Programming Manual 19
5.4.4 4 Keys Binary + Facility Code, Wiegand 26-Bit
This option buffers 4 keys and outputs keypad data with a 3-digit
facility code like a standard 26-bit card output.
The Facility code is set in Programming Menu 4 four and can be in the
range 000 to 255. The factory default setting for the facility code is
001 (see Section 5.7 for more information).
The keypad PIN code must be 4 digits in length and can range
between 0000 and 9999. On the fourth key press of the 4-digit PIN
code, the data is sent across the Wiegand Data lines as binary data in
the same format as a 26-Bit card.
If *or #is pressed during PIN code entry, the keypad clears the PIN
code entry buffer, generates a beep and is ready to receive a new 4-
digit keypad PIN code.
If the entry of the 4-digit keypad PIN code is disrupted and no number
key is pressed within 5 seconds, the keypad clears the PIN code entry
buffer, generates a beep and is ready to receive a new 4-digit keypad
PIN code.
(EP) FFFF FFFF AAAA AAAA AAAA AAAA (OP)
Where: EP = Even parity for first 12 bits
OP = Odd parity for last 12 bits
F = 8-Bit Facility code
A = 24-Bit code generated from keyboard
5.4.5 1 to 5 Keys + Facility Code, Wiegand 26-Bit
This option buffers up to 5 keys and outputs keypad data with a
facility code like a 26-bit card output.
The Facility code is set in Programming Menu 4 and can be in the
range 000 to 255. The factory default setting for the Facility code is
001 (see Section 5.7).
The keypad PIN code can be one to five digits in length and can range
between 0 and 65,535. When entering a keypad PIN code that is less
than 5 digits in length, #must be pressed to signify the end of PIN
code entry. For keypad PIN codes that are 5 digits in length, on the

Keypad Programming Instructions
20 AY-T6350 Installation and Programming Manual
fifth key press of the 5-digit PIN code, the data is sent across the
Wiegand Data lines as binary data in the same format as a 26-bit
card.
If *is pressed during PIN code entry or a PIN code greater than
65,535 is entered, the keypad clears the PIN code entry buffer,
generates a beep and is ready to receive a new 4-digit keypad PIN
code.
If the entry of the 1- to 5-digit keypad PIN code is disrupted and no
number key is pressed within 5 seconds, the keypad clears the PIN
code entry buffer, generates a medium length beep and is ready to
receive a new 1- to 5-digit keypad PIN code.
(EP) FFFF FFFF AAAA AAAA AAAA AAAA (OP)
Where: EP = Even parity for first 12 bits
OP = Odd parity for last 12 bits
F = 8-Bit Facility code
A = 24-Bit code generated from keyboard
5.4.6 6 Keys BCD and Parity Bits, Wiegand 26-Bit
This option sends a buffer of 6 keys, adds parity, and sends a 26-bit
BCD message. Each key is a four bit equivalent of the decimal
number.
The keypad PIN code must be 6 key presses long. On the sixth key
press of the 6-digit PIN code, (# and * keys are valid), the data is sent
across the Wiegand Data lines as a BCD message.
If the entry of the 6-digit keypad PIN code is disrupted and no number
key is pressed within 5 seconds, the keypad clears the PIN code entry
buffer, generates a medium length beep and is ready to receive a new
6-digit keypad PIN code.
(EP) AAAA BBBB CCCC DDDD EEEE FFFF (OP)
Where:
A = The first key entered D = Fourth key entered
B = Second key entered E = Fifth key entered
C = Third key entered F = Sixth key entered