Rosslare AY-K20C User manual

AY-K20C
Multi Format Proximity Card Reader
INTRODUCTION & KEY FEATURES
The AY-K20C Series Prox Readers are RFID proximity card readers
to be installed for use with access control systems. This instruction
manual contains information regarding the features, mounting,
wiring, operating instructions and warranty details for the AY-K20C
series readers.
GENERAL FEATURES
•SelectableWiegand 26-Bit, Wiegand 37-Bit, or Seriel RS232
•Reads EM 4102 or Rosslare Format Cards
•Waterproof
•Green LED control line
•Red LED control line
•Buzzer control line
•Hold control line
•Optical tamper sensor
•Tamper output line
•UV Protected olycarbonate housing
•Mounting Template for quick installation
MOUNTING INSTRUCTIONS
To mount the Reader, perform the following:
1. Determine an appropriate mounting position for the Reader.
2. Peel off the back of the self-stick mounting label template
included with the unit and place at the desired mounting
position.
3. Using the template as a guide, drill two holes (hole size is
4. indicated on mounting template) for mounting the Reader
to the surface.
5. Drill a 7/16" (10mm) hole for the cable. If mounting on metal,
place a grommet or electrical tape around the edge of the
hole.
6. Route the interface cable from the Reader to the Controller.
A linear type power supply is recommended.
Note: The prox reader can also be mounted using epoxy glue.
After application, the reader should be firmly held in place
until the glue dries.
Note: Card Readers are to be used with control panels whose power
supply is UL Listed Class 2 or equivalent.
WIRING INSTRUCTIONS
The Prox Reader is supplied with an 18-inch pigtail, having a 6-
conductor cable. To connect the Reader to the Controller,
perform the following steps:
1. Prepare the Reader cable by cutting the cable jacket back
1 inches and strip the wires inch.
2. Prepare the Controller cable by cutting the cable jacket
back 1 inches and strip the wires inch.
3. Splice the Reader pigtail wires to the corresponding
Controller wires and cover each connection (see Figure 2).
4. If the tamper output is being utilized, connect the purple
wire to the correct input on the Controller.
5. Trim and cover all conductors that are not used.
WIRE COLOR WIEGAND 26-
BIT OUTPUT
MODE
WIEGAND 37-
BIT OUTPUT
MODE
SERIEL
(RS232)
OUTPUT
MODE
Red +DC +DC +DC
Black Ground Ground Ground
Green Data 0 Data RS232
White Data 1 Clock -
Orange Green LED Green LED Green LED
Brown Red LED Red LED Red LED
Yellow Buzzer Buzzer Buzzer
Blue Hold Hold Hold
Purple Tamper Tamper Tamper
Grey Connected
to GND Open Input Connect to +DC
OPERATION INSTRUCTIONS
TESTING THE READER AND CARD READING
The Reader should be tested after wiring it to a power supply and
the Controller. Do this by performing the following steps:
1. Power up the Reader. The LED and Beeper will activate one
time. This indicates that the Reader is working properly.
2. Present the appropriate type of proximity card to the
Reader. The LED will momentarily flash green and a short
beep will be emitted. This indicates that the card was read
properly by the Prox Reader.
3. After the card data is processed by the Controller, the
Controller can then turn the LED green. Refer to the
Controller description of the LED operation if the Reader LED
is controlled by the Controller.
OUTPUT SELECTION
ForWiegand 26-bit operation the grey wire should be connected
to the ground, for Wiegand 37-Bit operation the grey wire should
be held not connected, for Serial RS232 operation the grey wire
should be held to +DC (VIN).
LED CONTROL
If the LED control wires (orange and brown) are not used (open)
the reader LED will remain red continuously and when successfully
reading a card the reader will flash the LED green momentarily.
The Bi-Color LED color can be controlled using the orange and
brown wires. When the orange wire is held to ground the LED will
be green; when the brown wire is held to ground the LED will be
red; when both the brown and orange wires are held to ground
the LED will be amber.
BUZZER CONTROL
If the buzzer control wire (yellow) is not used (open) the buzzer will
beep only when a card is read successfully. The buzzer can also
be controlled using the yellow wire. When the yellow wire is held
to ground the buzzer will sound.
HOLD CONTROL
The reading of cards can be disabled using the hold wire (blue). If
the blue wire is held to ground the reader will ignore all cards
placed in its field. If the blue wire is open the reader will read
cards normally.

TAMPER OUTPUT
This reader has an optical tamper sensor; when the sensor detects
light the tamper output is held to ground; when the sensor does
not detect light the tamper out put is held high open collector.
READ RANGE
A read range of 8cm is measured using Rosslare proximity cads
(P/N AT-11/14) or equivalent. Range also depends on electrical
environment and/or proximity to metal.
SPECIFICATIONS
Electrical Characteristics:
Power Supply Type Linear Type Recommended
Operating Voltage Range 5-16 VDC
Maximum Input Current Standby: 65mA
Read: 100mA
Tamper Output Open collector, active low,
max. sink current is 16mA
Maximum Cable Distance to
Controller 150 meters (500ft.)
RF Modulation ASK, 125KHz
Card Reading Distance See Table 1
Cable length 3M
Operating Temperature Range -31° C to 63° C (-25° F to 145° F)
Operating Humidity 0 to 95% (non condensing)
Dimensions 79.91 x 39.91 x 12.80
TECHNICAL SUPPORT
Asia Pacific, Middle East and Africa
Rosslare Security Products Headquarters
905-912 Wing Fat Industrial Bldg,
12 Wang Tai Road,
Kowloon Bay Hong Kong
Tel: [phone]
Fax: [phone]
E-mail: support.[email protected]
United States and Canada
1600 Hart Court,
Suite 103 Southlake,
TX, USA 76092
Toll Free: [phone]
Local: [phone]
Fax: [phone]
E-mail: [email protected]
Europe
Global Technical Support & Training Center
HaMelecha 22,
Rosh HaAyin, Israel 48091
Tel: [phone]
Fax: [phone]
E-mail: [email protected]
South America
Pringles 868, 1640 Martinez,
Buenos Aires, Argentina
Tel: [phone]
Fax: [phone]
Web Site: www.rosslaresecurity.com
LIMITED WARRANTY
ROSSLARE ENTERPRISES LIMITED S (Rosslare) FIVE YEARS LIMITED WARRANTY
is applicable worldwide. This warranty supersedes any other warranty. Rosslare's FIVE
YEARS LIMITED WARRANTY is subject to the following conditions:
Warranty
Warranty of Rosslare's products extends to the original purchaser (Customer) of the
Rosslare product and is not transferable.
Products Covered By This Warranty and Duration
ROSSLARE ENTERPRISES LTD. AND / ORSUBSIDIARIES (ROSSLARE) warrants that
the AY-K20C, to be free from defects in materials and assembly in the course of normal
use and service. The warranty period commences with the date of shipment to the original
purchaser and extends for a period of 5 years (60 Months).
Warranty Remedy Coverage
In the event of a breach of warranty, ROSSLARE will credit Customer with the price of the
Product paid by Customer, provided that the warranty claim is delivered to ROSSLARE by
the Customer during the warranty period in accordance with the terms of this warranty.
Unless otherwise requested by ROSSLARE ENTERPRISES LTD. AND / OR
SUBSIDIARIES representative, return of the failed product(s) is not immediately required.
If ROSSLARE has not contacted the Customer within a sixty (60) day holding period
following the delivery of the warranty claim, Customer will not be required to return the
failed product(s). All returned Product(s), as may be requested at ROSSLARE
ENTERPRISES LTD. AND /OR SUBSIDIARY’S sole discretion, shall become the
property of ROSSLARE ENTERPRISES LTD. AND /OR SUBSIDIARIES.
To exercise the warranty, the user must contact Rosslare Enterprises Ltd. to obtain an
RMA number after which, the product must be returned to the Manufacturer freight
prepaid and insured
In the event ROSSLARE chooses to perform a product evaluation within the sixty (60) day
holding period and no defect is found, a minimum US$ 50.00 or equivalent charge will be
applied to each Product for labor required in the evaluation.
Rosslare will repair or replace, at its discretion, any product that under normal conditions
of use and service proves to be defective in material or workmanship. No charge will be
applied for labor or parts with respect to defects covered by this warranty, provided that
the work is done by Rosslare or a Rosslare authorized service center.
Exclusions and Limitations
ROSSLARE shall not be responsible or liable for any damage or loss resulting from the
operation or performance of any Product or any systems in which a Product is
incorporated. This warranty shall not extend to any ancillary equipment not furnished by
ROSSLARE, which is attached to or used in conjunction with a Product, nor to any
Product that is used with any ancillary equipment, which is not furnished by ROSSLARE.
This warranty does not cover expenses incurred in the transportation, freight cost to the
repair center, removal or reinstallation of the product, whether or not proven defective.
Specifically excluded from this warranty are any failures resulting from Customer's
improper testing, operation, installation, or damage resulting from use of the Product in
other than its normal and customary manner, or any maintenance, modification, alteration,
or adjustment or any type of abuse, neglect, accident, misuse, improper operation,
normal wear, defects or damage due to lightning or other electrical discharge. This
warranty does not cover repair or replacement where normal use has exhausted the life of
a part or instrument, or any modification or abuse of, or tampering with, the Product if
Product disassembled or repaired in such a manner as to adversely affect performance or
prevent adequate inspection and testing to verify any warranty claim.
ROSSLARE does not warrant the installation, maintenance, or service of the Product.
Service life of the product is dependent upon the care it receives and the conditions under
which it has to operate.
In no event shall Rosslare be liable for incidental or consequential damages.
Limited Warranty Terms
THIS WARRANTY SETS FORTH THE FULL EXTENT OF ROSSLARE ENTERPRISES LTD.
AND IT’S SUBSIDIARY’S WARRANTY
THE TERMS OF THIS WARRANTY MAY NOT BE VARIED BY ANY PERSON,WHETHER OR
NOT PURPORTING TO REPRESENT OR ACT ON BEHALF OF ROSSLARE.
THIS LIMITED WARRANTY IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES.ALL
OTHER WARRANTIES EXPRESSED OR IMPLIED,INCLUDING WITHOUT LIMITATION,
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE,ARE SPECIFICALLY EXCLUDED.
IN NO EVENT SHALL ROSSLARE BE LIABLE FOR DAMAGES IN EXCESS OF THE
PURCHASE PRICE OF THE PRODUCT,OR FOR ANY OTHER INCIDENTAL,
CONSEQUENTIAL OR SPECIAL DAMAGES,INCLUDING BUT NOT LIMITED TO LOSS OF
USE,LOSS OF TIME,COMMERCIAL LOSS,INCONVENIENCE,AND LOSS OF PROFITS,
ARISING OUT OF THE INSTALLATION,USE,OR INABILITY TO USE SUCH PRODUCT,TO
THE FULLEST EXTENT THAT ANY SUCH LOSS OR DAMAGE MAY BE DISCLAIMED BY LAW.
THIS WARRANTY SHALL BECOME NULL AND VOID IN THE EVENT OF A VIOLATION OF
THE PROVISIONS OFTHIS LIMITEDWARRANTY.
0706-0960293+00