Rosslare AYC-E65BB Assembly instructions

AYC-Ex5/T65 Series
Convertible Backlit Proximity &
PIN Readers/Controllers
Installation and Programming Manual
Ex5 Models:
AYC-E55
AYC-E65BB
AYC-E65BG
AYC-E65BW
T65 Models:
AYC-T65B
AYC-T65N
AYC-Ex5
AYC-T65

Copyright © 2017 by Rosslare. All rights reserved.
This manual and the information contained herein are proprietary to ROSSLARE
ENTERPRISES LIMITED and/or its related companies and/or subsidiaries’
(hereafter: "ROSSLARE"). Only ROSSLARE and its customers have the right to
use the information.
No part of this manual may be re-produced or transmitted in any form or by any
means, electronic or mechanical, for any purpose, without the express written
permission of ROSSLARE.
ROSSLARE owns patents and patent applications, trademarks, copyrights, or
other intellectual property rights covering the subject matter in this manual.
TEXTS, IMAGES, AND ILLUSTRATIONS INCLUDING THEIR ARRANGEMENT IN
THIS DOCUMENT ARE SUBJECT TO THE PROTECTION OF COPYRIGHT LAWS
AND OTHER LEGAL RIGHTS WORLDWIDE. THEIR USE, REPRODUCTION, AND
TRANSMITTAL TO THIRD PARTIES WITHOUT EXPRESS WRITTEN PERMISSION
MAY RESULT IN LEGAL PROCEEDINGS.
The furnishing of this manual to any party does not give that party or any third
party any license to these patents, trademarks, copyrights or other intellectual
property rights, except as expressly provided in any written agreement of
ROSSLARE.
ROSSLARE reserves the right to revise and change this document at any time,
without being obliged to announce such revisions or changes beforehand or
after the fact.

Table of Contents
AYC-Ex5/T65 Series Installation and Programming Manual iii
Table of Contents
1. Introduction ................................................................9
1.1 Reader/Controller Types........................................................... 9
1.2 Box Content ......................................................................... 10
1.3 Ancillary Equipment .............................................................. 10
2. Technical Specifications............................................11
3. Installation ................................................................13
3.1 Mounting ............................................................................. 13
3.2 Wiring .................................................................................. 14
3.2.1 Wiring the Unit as a Reader ..........................................................14
3.2.2 Wiring the Unit as a Controller .....................................................15
4. Reader Operation......................................................18
4.1 Standby Mode ...................................................................... 18
4.2 Programming as a Reader...................................................... 18
4.2.1 Entering Programming Mode........................................................20
4.2.2 Exiting Programming Mode ..........................................................20
4.2.3 Selecting Keypad Transmission Format .........................................21
4.2.4 Selecting Proximity Card Transmission Format ..............................26
4.2.5 Changing the Programming Code ................................................28
4.2.6 Changing the Facility Code ...........................................................28
4.2.7 Setting the Backlight Behavior ......................................................29
4.2.8 Return to Factory Default Settings ................................................30
4.2.9 Replacing a Lost Programming Code ............................................30
5. Controller Operation.................................................31
5.1 Normal, Secure, and Master Users.......................................... 31

Table of Contents
iv AYC-Ex5/T65 Series Installation and Programming Manual
5.2 Modes of Operation.............................................................. 32
5.2.1 Normal Mode ...............................................................................32
5.2.2 Bypass Mode ................................................................................32
5.2.3 Secure Mode ................................................................................33
5.2.4 Changing the Modes of Operation ...............................................33
5.3 Auxiliary Input and Output..................................................... 35
5.4 Door Alarms ......................................................................... 35
5.5 Internal Case and Back Tamper.............................................. 35
5.6 Lockout Feature (Keypad Tamper) .......................................... 35
5.7 REX Function ........................................................................ 35
5.8 Secured Intelligent Power Supply ........................................... 36
5.9 Programming as a Controller ................................................. 36
5.9.1 Entering Programming Mode........................................................37
5.9.2 Exiting Programming Mode ..........................................................38
5.9.3 Changing Lock Strike Code ..........................................................38
5.9.4 Changing Auxiliary Code ..............................................................39
5.9.5 Changing the Programming Code ................................................40
5.9.6 Changing the Normal/Secure Code ..............................................40
5.9.7 Changing the Normal/Bypass Code and Door Chime Settings ......41
5.9.8 Setting Fail Safe/Secure Operation, Tamper Siren and Lock Strike
Release Time.................................................................................42
5.9.9 Defining the Auxiliary Input and Output .......................................43
5.9.10 Setting the Lockout Feature ..........................................................49
5.9.11 Setting the Backlight Behavior ......................................................50
5.9.12 Enrolling Primary and Secondary Codes ........................................50
5.9.13 Deleting Primary and Secondary Codes.........................................55
5.9.14 Relay Codes Assignment...............................................................57
5.9.15 PIN Code Length/Factory Default Settings.....................................60

Table of Contents
AYC-Ex5/T65 Series Installation and Programming Manual v
5.9.16 Replacing a Lost Programming Code ............................................60
5.9.17 Exiting Secure Mode if Normal/Secure Code was Lost...................61
A. Declaration of Conformity........................................62
B. Limited Warranty ......................................................63

List of Figures
vi AYC-Ex5/T65 Series Installation and Programming Manual
List of Figures
Figure 1: Drilling and Mounting Template .......................................................13
Figure 2: Controller Application Wiring Diagram .............................................16
Figure 3: Controller Wiring – Using the Internal Power ....................................17
Figure 4: Controller Wiring – Using the External Power ...................................17

List of Tables
AYC-Ex5/T65 Series Installation and Programming Manual vii
List of Tables
Table 1: Wiring the Reader to the Controller ...................................................14
Table 2: Wiring the Unit as a Controller...........................................................15
Table 3: Reader Programming Menus..............................................................19
Table 4: Controller Programming Menu ..........................................................37
Table 5: Quick Reference Guide for Auxiliary Mode Setting.............................44
Notice and Disclaimer
This manual’s sole purpose is to assist installers and/or users in the safe and
efficient installation and usage of the system and/or product, and/or software
described herein.
BEFORE ATTEMPTING TO INSTALL AND/OR USE THE SYSTEM,THE INSTALLER AND THE
USER MUST READ THIS MANUAL AND BECOME FAMILIAR WITH ALL SAFETY
REQUIREMENTS AND OPERATING PROCEDURES.
The system must not be used for purposes other than those for which it
was designed.
The use of the software associated with the system and/or product, if
applicable, is subject to the terms of the license provided as part of the
purchase documents.
ROSSLARE exclusive warranty and liability is limited to the warranty and
liability statement provided in an appendix at the end of this document.
This manual describes the maximum configuration of the system with the
maximum number of functions, including future options. Therefore, not all
functions described in this manual may be available in the specific system
and/or product configuration you purchased.
Incorrect operation or installation, or failure of the user to effectively
maintain the system, relieves the manufacturer (and seller) from all or any
responsibility for consequent noncompliance, damage, or injury.
The text, images and graphics contained in the manual are for the purpose
of illustration and reference only.

Introduction
8 AYC-Ex5/T65 Series Installation and Programming Manual
All data contained herein subject to change without prior notice.
In no event shall manufacturer be liable for any special, direct, indirect,
incidental, consequential, exemplary or punitive damages (including,
without limitation, any and all damages from business interruption, loss of
profits or revenue, cost of capital or loss of use of any property or capital or
injury).
All graphics in this manual are for reference only, some deviation between
the image(s) and the actual product may occur.
All wiring diagrams are intended for reference only, the photograph or
graphic of the PCB(s) are intended for clearer illustration and
understanding of the product and may differ from the actual PCB(s).

Introduction
AYC-Ex5/T65 Series Installation and Programming Manual 9
1. Introduction
The AYC-Ex5/T65 series are integrated convertible readers and
controllers with a piezoelectric keypad. The units are vandal resistant
and water resistant, suitable for indoor or outdoor mounting.
These units automatically determine whether to function as a reader
or as a controller. If the unit is connected to a standard access control
unit, then it functions as a reader. If the unit is connected to a
Rosslare secured intelligent power supply such as the PS-A25T,
PS-C25T or PS-C25TU, it functions as a secured controller.
As a controller, the units accept up to 500 users, and allow entry via a
personal identification number (PIN) and/or by presenting a proximity
card. The PIN code length for the controller has several options. The
PIN code length can be a set number of 4, 5, or 6 digits or it can be a
4- to 8-digit code.
For information on how the unit functions as a reader, see Chapter 4.
For information on how the unit functions as a controller, see
Chapter 5.
1.1 Reader/Controller Types
The different types of units described in this manual are:
Type E55 has PIN only
Types E65 and T65 have PIN and proximity card
Backlight
Keypad
Type
Proximity
AYC-E55 Piezoelectric 
AYC-E65B Piezoelectric 
AYC-E65BB Piezoelectric 
AYC-T65 Piezoelectric 

Introduction
10 AYC-Ex5/T65 Series Installation and Programming Manual
1.2 Box Content
Before beginning verify that all of the following is in the box. If
anything is missing, please report the discrepancy to your nearest
Rosslare office.
One AYC-Ex5/T65 unit
Installation kit
Installation and operating instructions
1.3 Ancillary Equipment
The following equipment is required to complete your installation:
When functioning as a reader:
Compatible host controller (not supplied)– UL listed access
control unit, such as model AC-215U
When functioning as a controller:
Secured intelligent power supply (such as the PS-A25T, PS-C25T
or PS-C25TU)
The controller connects to the following:
Electric lock strike mechanism or a magnetic lock device,
which implements fail safe (power to lock) or fail secure
(power to open) functions.
Request-to-Exit (REX) button – normally open type
Switch is closed when pressed.
Door monitor switch
Rosslare accessories can be found on www.rosslaresecurity.com.

Technical Specifications
AYC-Ex5/T65 Series Installation and Programming Manual 11
2. Technical Specifications
Specification AYC-E55 AYC-E65B,
AYC-E65BB
AYC-T65
Electrical Characteristics
Power Supply Type Linear type (recommended)
Operating Voltage
Range
5–16 VDC (when used as a controller, provided by the
secured intelligent power supply)
Input Current
Standby
15 m A@12 VDC 92 mA @12 VDC
Max Input Current 40 mA @16 VDC 105 mA @16 VDC
LED Control Input Dry contact N.O.
Tamper Output Open collector, active low, 30 mA max sink current
Cable Distance to
Host Controller
Up to 500 ft. (150 meters) using an 18 AWG cable
Max. Proximity
Card Read Range*
N/A 40 mm (1.6 in.)
Proximity Card
Modulation
N/A ASK at 125 kHz
Proximity Card
Compatibility
N/A EM cards
Card Transmit
Format (Reader)
N/A Wiegand 26-Bit, or Clock & Data
Keypad Transmit
Format (Reader)
Programmable PIN code formats
LED Indicators Two tri-colored LEDs
Communication Data1/C1, Data0/C2—open collector, 5 V termination
* Measured using a Rosslare proximity card or equivalent. Range also
depends on electrical environment and proximity to metal.

Technical Specifications
12 AYC-Ex5/T65 Series Installation and Programming Manual
Specification AYC-E55 AYC-E65B,
AYC-E65BB
AYC-T65
Environmental Characteristics
Operating Temp.
Range
-30°C to 65°C (-22°F to 150°F)
Operating Humidity
Range
0 to 95% (non-condensing)
Outdoor Usage Weather-resistant, meets IP68, epoxy-potted, suitable
for outdoor use
Physical Characteristics
Size
(Height x Width x
Depth)
155 x 44 x 6.5
mm
(6.1 x 1.7 x 0.3
in.)
155 x 44 x 9 mm
(6.1 x 1.7 x 0.4
in.)
121 x 70 x 8 mm
(4.8 x 2.8 x 0.3
in.)
Weight
120 g (4.2 oz) 143 g (5.0 oz) 121 g (4.3 oz)

Installation
AYC-Ex5/T65 Series Installation and Programming Manual 13
3. Installation
Installation of an RFID reader adjacent to metallic surfaces
might alter the reader’s specifications. To diminish this
interference, use a plastic spacer when mounting the reader.
3.1 Mounting
Before starting, select the location to mount the unit. This location
should be at shoulder height.
To mount the unit:
1. Peel off the back of the self-adhesive mounting label template
and place it on the required mounting location.
2. Using the template as a guide, drill two holes (of the size
indicated on the template) on the surface to mount the unit
(Figure 1).
Figure 1: Drilling and Mounting Template
AYC-Ex5 AYC-T65

Installation
14 AYC-Ex5/T65 Series Installation and Programming Manual
3. Insert the wall plugs into both mounting holes.
4. Drill a 10-mm (7/16”) hole for the cable. If the surface is metal,
place a grommet or electrical tape around the edge of the hole.
5. Insert the unit’s cable wire into the cable hole and wire the unit
as described in Section 3.2.
6. Using the two mounting screws, screw the unit to the wall
through the two wall plugs.
The unit can also be mounted using strong epoxy glue. After
application, firmly hold the unit in place until the glue dries.
3.2 Wiring
The unit is supplied with a 6-conductor 150-cm (60-in.) pigtail with
exposed wires coated with solder.
3.2.1 Wiring the Unit as a Reader
If you connect the unit to a standard access control unit, it
automatically functions as a reader.
To connect the unit as a reader (to a controller):
1. Select the appropriate connections according to Table 1.
Table 1: Wiring the Reader to the Controller
Wire Color Function
Black/Shield Ground (+)
Red Vin (-)
Green Data 0/Data (D0)
White Data 1/Clock (D1)
Brown LED control
Purple Tamper
2. Prepare the controller cable by cutting the cable jacket back 3.2
cm (1¼”) and strip the wire 1.3 cm (½”).
3. Splice the reader’s pigtail wires to the corresponding controller
wires and cover each joint with insulating tape.

Installation
AYC-Ex5/T65 Series Installation and Programming Manual 15
4. If the tamper output is being utilized, connect the purple wire to
the correct input on the controller.
5. Trim and cover all conductors that are not used.
•The individual wires extending from the reader are color-coded
according to the required Wiegand standard.
•When using a separate power supply for the reader, this supply and
the controller’s power supply must have a common ground. A linear
power supply is recommended.
•Attach the cable shield wire on the reader to an earth ground (best),
or to a signal ground connection at the panel or power supply end of
the cable. This configuration is best for shielding the reader cable
from external interference.
3.2.2 Wiring the Unit as a Controller
If you connect the unit to a Rosslare PS-x25x secured power supply, it
automatically functions as a controller.
To connect the unit as a controller:
1. Select the appropriate connections according to Table 2.
Table 2: Wiring the Unit as a Controller
Controller Wire Color Function Note
- Red +DC Input Wired to the PS-x25x
+ Black Ground Wired to the PS-x25x
C 1 White Communication Wired to the PS-x25x
C 2 Green Communication Wired to the PS-x25x
AUX. IN Brown Auxiliary Input Wired to input
N/A Purple Not in use N/A
Attach the cable shield wire on the unit to an earth ground (best).
You can also attach it to a signal ground connection at the panel or
power supply end of the cable. This configuration is best for
shielding the controller cable from external interference.
2. Prepare the PS-x25x secured power supply’s cable by cutting the
cable jacket back 3.2 cm (1¼”) and strip the wire 1.3 cm (½”).

Installation
16 AYC-Ex5/T65 Series Installation and Programming Manual
3. Splice the controller pigtail wires to the corresponding PS-x25x
secured power supply’s wires and cover each joint with insulating
tape.
4. Trim and cover all conductors not used.
5. To connect the unit to the desired power supply option, refer to
the relevant wiring diagrams that follow.
Figure 2 shows the wiring for the controller application using a dual
relay secured intelligent power supply.
Figure 2: Controller Application Wiring Diagram

Installation
AYC-Ex5/T65 Series Installation and Programming Manual 17
Figure 3 shows the auxiliary output connection using the internal
power.
Figure 3: Controller Wiring – Using the Internal Power
Figure 4 shows the auxiliary output connection using the external
power.
Figure 4: Controller Wiring – Using the External Power

Reader Operation
18 AYC-Ex5/T65 Series Installation and Programming Manual
4. Reader Operation
The AYC-Ex5/T65 series can function both as a reader and as a
controller. If the unit is connected to standard access controller, it
functions as a reader, indicated by one beep immediately after power-
on reset.
The use of a proximity card is not relevant for the AYC-E55
model.
4.1 Standby Mode
The default mode of the reader is Standby mode. In Standby mode,
the unit is ready to receive data from a presented proximity card or an
entered PIN code.
When the reader is in Standby mode, the left LED
is red and the right LED is off.
When a proximity card is presented or a keypad
entry is being transmitted, the left LED flashes
green.
Keypad data can be sent via one of eight keypad transmission formats
(see Section 4.2.3).
Proximity cards presented to the reader are always sent in either
Wiegand 26-Bit, Clock & Data or, Wiegand Card + PIN format (see
Section 4.2.4).
4.2 Programming as a Reader
Programming is done solely via the unit's keypad driven Programming
Menu System. During the manufacturing process, certain codes and
settings are pre-programmed. These settings are called the default
factory settings.
Table 3 shows the names of all the reader programming menus.
Default factory settings are marked by a "*" sign.
Green
Red

Reader Operation
AYC-Ex5/T65 Series Installation and Programming Manual 19
Table 3: Reader Programming Menus
Menu Description Default
1 Selecting Keypad Transmission Format
Single Key, Wiegand 6-Bit (Rosslare Format)
Single Key, Wiegand 6-Bit with Nibble + Parity Bits
Single Key, Wiegand 8-Bit, Nibbles Complemented
4 Keys Binary + Facility Code, Wiegand 26-Bit
1 to 5 Keys + Facility Code, Wiegand 26-Bit
6 Keys BCD and Parity Bits, Wiegand 26-Bit
Single Key, 3x4 Matrix Keypad
1 to 8 Keys BCD, Clock & Data
*
2 Selecting Card Transmission Format
Wiegand 26-Bit
Clock & Data
Wiegand Card + PIN
*
3 Changing the Programming Code 1234
4 Changing the Facility Code 0
6 Backlight Options
Off
On (default)
Off until key press when on for 10 seconds
Dimmed until key press when on for 10 seconds
*
0 Return to Factory Default Settings

Reader Operation
20 AYC-Ex5/T65 Series Installation and Programming Manual
4.2.1 Entering Programming Mode
To reach the Programming Menu System, the unit must first be
placed into Programming mode.
•The factory 4-digit Programming code is 1234.
•If a Programming code is not entered within 30 seconds, the unit
returns to Standby mode.
To enter Programming mode:
1. Press #four times.
The left LED turns off and the right LED turns
red.
2. Enter your 4-digit Programming code.
If the Programming code is valid, the right LED
turns green.
If the Programming code is invalid, you hear a long beep and the
reader returns to Standby mode.
4.2.2 Exiting Programming Mode
To exit Programming mode:
1. Press #to exit Programming mode at any time.
You hear a beep.
The left LED turns red and the right LED
turns off.
This indicates that the unit has returned to Standby mode.
Wrong entries may reset the reader back to Standby mode. If no
key is pressed for 30 seconds while in Programming mode, the
unit exits Programming mode and returns to Standby mode.
Red
Green
Red