Rossmax NC300 User manual

For a�er sales service, pleasecontact Cypress Medic Sdn Bhd (www.cypressmedic.com.my)
Rossmax Nebulizer NC300
Quick Guide
A. Installing Batteries
1. Follow the direcon of the arrow to open the baery cover and install or replace 2 “AA” sized baeries in
the baery compartment according to the indicaons inside the compartment, then fold the baery cover
to cover it.
2. Replace the baries in pairs. Remove baries when unit is not in use for extended periods of me.
You need to replace the baeries when
a. Low baery indicator (green) shes on LED.
b. The ON/OFF buon is pressed and nothing appears on LED.
Caution:
1. Baries are hazardous waste. Do not dispose them together with the household garbage.
2. There are no user serviceable parts inside. Baries or damage from old baeries are not covered by
warranty.
3. Use only alkaline baeries or nickel-metal-hydride rechargeable baeries. Always replace with new
baeries together. Use baeries of the same brand and same type.
B. Using the AC Adapter
1. Connect the AC adapter with the AC adapter jack in the back of the unit.
2. Plug the AC adapter into the socket. (AC adapters with required voltage and current indicated near the AC
adapter jack.)
Caution:
1. Please unload the baries when operang with the AC mode for a longer period of me.
2. Use only the authorized AC Adaptor with this nebulizer.
3. AC adaptor cannot be used for charging baries.
A B

For a�er sales service, pleasecontact Cypress Medic Sdn Bhd (www.cypressmedic.com.my)
C. Assembling your nebulizer kit
Follow the cleaning instrucons in this guidebook under “Cleaning technique” prior to using your nebulizer for
the rst me or aer it has been stored for an extended period of me.
REMEMBER: Always unplug the nebulizer and make sure the power-switch is turned to the “OFF” posion
before cleaning, assembling and before or aer each use.
1. Remove the cup casing from the main unit by pressing release buons on both sides.
2. Remove the medicaon cup from cup casing by pressing bracket inwards lightly and drawing the medicaon
cup out.
NOTE: Do not touch the Mesh.
3. Follow the sign on the top medicaon cover to “Open” the cover.
4. Add the prescribed amount of medicaon to the medicaon cup.
NOTE: If high-viscosity medicine is used, nebulizaon may be reduced.
5. Align an arrow on the top medicaon cover with medicaon cup’s scale as illustrated to cover over.
6. Follow the sign on the top medicaon cover to “Close” the cover.
7. Install the medicaon cup into the medicaon casing unl you hear it click.
NOTE: Make sure that the two parts t securely.
8. Place the cup casing onto the main unl you hear it click into place on the leand right sides.
NOTE: Before placing the cup casing with main unit, ensure that the baeries or the adaptor are inserted.
D. Operating your nebulizer
The nebulizer is operable at up to a 45° angle. If the angle is greater than 45°, no aerosol will be generated.
1. Ach the mask connector to the nebulizer and install the mask on the mask connector or aach the
angled mouthpiece to the top of the nebulizer.
2. The recommended ng amount is between 2~6 ml in medicaon cup.
3. Power on the On/Obuon to start for nebulizaon. When device is ready, the LED stays on green.
Caution:
1. Do not touch the air port on the top medicaon cover when nebulizaon.
2. If the therapy requires various dierent medicines be inhaled one aer another, ensure the nebulizer is
cleaned aer every nebulizaon.
3. Do not aempt to operate the nebulizer if the medicaon cup is empty.
4. If the medicaon cup is empty, be sure to power othe device in advance, and then wait about 10
minutes before ng in the medicaon and starng the nebulizaon.
5. To prevent damage to the mesh, the nebulizer power oautomacally aer operang for15 minutes.
Operating your nebulizer
Aer every use:
1. Switch the device, unplug the device from the power source.
2. Carefully detach the accessories and medicaon cup from the nebulizer and pour out any remaining liquid.
3. Follow the cleaning procedures provided in this guidebook.
C D

For a�er sales service, pleasecontact Cypress Medic Sdn Bhd (www.cypressmedic.com.my)
E. Cleaning procedures
1. Aer each treatment, ng 2ml of drinking water remove medicine residue from the mesh rst. (Please
nebulizaon the enre liquid)
2. Make sure to “Power OFF” the nebulizer and the unit has been disconnected from the power source.
3. Detach the mouthpiece or mask with mask connector from the nebulizer and pour out any remaining
liquid by ng 90°
4. Remove the cup casing from the main unit at rst by pressing release buons on both sides.
NOTE: Do not draw out the medicaon cup from cup casing in advance to avoid the remaining liquid
penetrang inside the electrodes.
5. Remove the medicaon cup from cup casing by pressing bracket inwards and drawing the medicaon cup
out.
6. Rinse the nebulizer components and accessories (not the main unit!) with tap water lower than 40ºC.
7. Ensure the electrodes on medicaon cup fully dry.
8. Dry with clean towels or completely air dry.
NOTE: Do not touch the mesh with any towels or with a pin.
NOTE:
1. For the rst me cleaning or aer the unit has been stored for an extended period of me, thoroughly
clean all components.
2. Do not clean the nebulizer or accessories in a dish-washer.
3. The nebulizer must be operated only when it is complete dry.
E