Rowlinson Garden Products Britannia Arbour User manual

x 2
No. Components Qty.
1Left upright 1
2Right upright 1
3Seat 1
4Seat back 1
5Back panel 1
6To p r a i l 1
7Roof panel 2
8Gusset 2
9Roof coverstrip 1
10 Bargeboard 4
11 Finial 2
No. Fixing kit Qty.
12 90mm screws 2
13 70mm screws 12
14 50mm screws 5
15 40mm screws 36
16
35mm screws 41
2
3
4
5
6
7
8
9
10
Britannia Arbour
Assembly Instructions
English SS307
2013 © Rowlinson Garden Products Ltd
If in doubt of any aspect regarding the assembly, use or safety of your arbour please contact us :
Help Line (Normal Office Hours) 01829 261 121
ROWLINSON GARDEN PRODUCTS LIMITED
Green Lane
Wardle Nr. Nantwich
Cheshire
CW5 6BN
We constantly improve the quality of our products, occasionally the
components may differ from the components shown and are only
correct at time of printing. We reserve the right to change the
specification of our products without prior notice.
I MPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
Periodically check all fastenings for tightness
For domestic use only
Safety information
5. Bargeboards and finials
Position bargeboards at the front so that the top edge is flush with the roof line and the two boards meet evenly in the
middle secure each board using 4 x 40mm and 1 x 70mm screws. Screw through the pre-drilled holes, using the diagram
below for the positions of the 70mm screws. Attach a finial centrally over the join between the bargeboards use
2 x 40mm screws. In the same way fit two bargeboards and a finial to the back of the arbour.
40mm
40mm
Before assembly
•We recommend that time is taken to
read the instructions before starting
assembly, then follow the easy step
by step guide.The instruction sheet
is only a guide to the assembly.
Certain items may not be shown to scale.
•Check all components prior to assembly
•This product should be assembled
by no less than two people.
•Never attempt to erect the assembly
in high winds.
Recommended tools for assembly
•Power drill/screwdriver
•Cross head screwdriver bit
11
70mm
40mm
40mm
70mm
40mm 70mm

70mm
1. Seat to upright
Position the seat between the two upright so it rests on the seat support rail. Have the seat as far forward as possible
so that the rebates in the front corners of the seat fit around the front legs of the upright. Secure the seat in place
using 2 x 70mm screws per upright. Screw up through the pre-drilled holes in the seat support rail into the frame of
the seat.
2. Seat back
Place the seat back so that the bottom rail of the seat back is up against the back rail of the seat. From the back screw
through the pre-drilled holes in rail of the seat back into the seat using 4 x 70mm screws.
4. Roof assembly
Join the two halves of the roof together using the two gussets. Position the gussets on the inside of the roof bearers.
Secure each gusset in place using 6 x 40mm screws. Place the roof coverstrip on top of the ridge and screw down at
each end using 2 x 40mm screws. Screw through the pre-drilled holes in the coverstrip into the roof panels. Lift the
roof onto the assembly. Ensure the rebates in the roof rafters rest on the upright and that the roof sits flush with
upright at the front and rear. Secure each front corner in place using 1 x 90mm screws. Screw up through the
pre-drilled holes in the upright into roof panels.
70mm
Bottom rail
of seat back.
Back rail
of seat.
70mm
50mm 50mm
35mm
3. Back panel
Position the back panel between the upright behind the seat. Ensure the panel is level with the top of the two uprights
and secure using 4 x 50mm screws. Screw through the pre-drilled holes in the panel into the leg of the upright. Using
1 x 50mm screw, screw through the pre-drilled hole in the back panel into the middle support of the seat back. Place
the top rail on top of the back panel as shown below. Ensure the top rail is sitting centrally and secure down using
4 x 35mm screws through the pre-drilled holes.
40mm
View of gusset fitted inside the roof.
40mm
40mm
90mm
Seat front corner
rebates
Seat support
rail 600mm
roof bearer