Rowlinson Garden Products SS305B User manual

1
2
3
12
6
8
x 2 drill
5
47
11
10
9
6. High level shelf
Position each shelf bracket at the desired height on the inside of the posts. Allow a gap at the back of the bracket
for the shelf bracket back board to sit between and flush to the back edge of the posts. Secure each bracket using
2 x40mm screws. When both brackets are in place fix the shelf bracket back board to the back edge of the brackets using
2 x 40mm screws at each end of the board. Screw the five hooks into you desired location. Place the two shelf boards
on top of the brackets and secure each board at each end with 2 x 40mm screws. Multifunction Table
Assembly Instructions
English SS305B
Information
13
14
15 16
No. Components Qty.
1Back panel 1
2Left panel 1
3Right panel 1
4Front rails 2
5Mid shelf support 2
6Shelf 2
7Shelf coverstrips 2
8 Work top 1
9Metal work top 1
10 Work top sides 2
11 Work top back board 1
12 High level shelf posts 2
13 Shelf bracket 2
14 Shelf bracket back board 1
15 Shelf board 2
16 Shelf back board 1
No. Fixing Kit Qty.
17 Hook 5
18 90mm screw 16
19 40mm screw 39
20 30mm screw 4
21 14mm screw 6
This product contains
sheet metal. Wear
protective work
gloves while handling
these components.
Gloves
Before assembly
•We recommend that time is taken to
read the instructions before starting
assembly, then follow the easy step by
step guide. The instruction sheet is only
a guide to the assembly. Certain items may
not be shown to scale.
•Check all components prior to assembly
•This product should be assembled
by no less than two people
•Drill all components where indicated
•Some of the components may have sharp
edges wear protective work gloves while
handling components.
It is recommended to drill a
pilot hole for each hooks with
a 3mm drill bit.
3mm
Drill
Recommended tools for assembly
•Power drill/screwdriver
•3mm drill bit
•Cross head screwdriver bit
•Tape measure
•Rubber mallet
•Spirit level
•Sharp knife
Important note:
Ensure the brackets
are positioned
so that the shelf
bracket back board
fits between the
posts.
40mm
40mm
40mm
2022 © Rowlinson Garden Products Ltd
We constantly improve the quality of our products, occasionally
the components may differ from the components shown and are
only correct at time of printing. We reserve the right to change the
specification of our products without prior notice.
If in doubt of any aspect regarding the assembly, use or safety of your Multifunction Table, please contact us:
Help Line (Normal Office Hours) 01829 261 121
Email: [e-mail]
ROWLINSON GARDEN PRODUCTS LIMITED
Green Lane
Wardle Nr. Nantwich
Cheshire
CW5 6BN
www.rowgar.co.uk
Important note:
When attaching the shelf
brackets, they can be set
at you’re preferred height.
Important note:
The five hooks can be positioned
at you’re preferred location.
For example, they can be evenly
spaced along the shelf bracket
backboard or into the worktop
sides.
Biocidal Products Regulation EU 528/2012
Wolmanit CX treated wood is a treated article that incorporates biocidal products: copper
hydroxide carbonate/II/ and boric acid. They protect wood against fungal decay /rot/ and
insect attack. Keep away from food, drink and animal feeding stuffs. Avoid breathing dust
when cutting treated wood.
CAUTION

3. Front rails
Position the front rails between the side panels secure through the pre-drilled holes using 2 x 90mm screws at each end
of each rail.
1. Back and side panels
Insert the back panel into the rebate on the back leg of each side panel. If necessary use a rubber mallet to tap into place.
Secure each side panel in place using 2 x 90mm screws. Screw through the pre-drilled holes in the side panel into the
ends of the back panel.
90mm 90mm
30mm
30mm
2. Shelves
Position the middle shelf supports at the desired height and attach to the inside of the side panels. Secure each one using
2 x 30mm screws, screw through the panel into the shelf support. Ensure both supports are at the same height. Insert
a shelf at the bottom so that it rests on the frame of the side panels. Rest the second shelf on the middle shelf supports.
90mm
90mm
40mm
4. Work top and shelf coverstrips
Place the work top onto the assembly ensure it has an overhang at the front and a gap at the back to allow for the work
top back board. Secure the work top down using 5 x 40mm screws. Attach the work top sides and back board using 4
x 40mm screws each side. Attach a coverstrip to the top of the lower front rail using 3 x 40mm screws. The remaining
coverstrip is secured to the front edge of the middle shelf using 3 x 40mm screws. Place the metal work top onto the
top of the assembly and secure in place using 6 x 14mm screws.
40mm
40mm
40mm 14mm
14mm
90mm
90mm
40mm
40mm
5. High level shelf posts
Determine the height you require the high level shelf and secure the shelf posts accordingly. Attach each post to the legs
on the back of the assembly using 2 x 90mm screws per post. Fix the shelf back board to each post using 2 x 40mm
screws.
Important note:
The lower rail must sit
lower that the top edge
of the shelf to allow
for the coverstrip to sit
on top.
Caution:
The Metal work top
may have sharp edges.
Wear protective gloves
whilst handling this part.
Gloves
40mm
Important note:
Ensure the the work top over hangs at the
front edge and there is a gap at the back to
allow for the work top back board.
Important note:
Ensure the posts are at the same height
Important note:
Ensure the shelf supports are at
the same height