Rowlinson Garden Products Haven Arbour User manual

Before assembly
•We recommend that time is taken to read the
instructions before starting assembly, then
follow the easy step by step guide.
The instruction sheet is only a guide to
the assembly. Certain items may not be
shown to scale.
•Check all components prior to assembly
•This product should be assembled by no
less than two people.
•Never attempt to erect the assembly in
high winds.
•Drill components where indicated.
Recommended tools for assembly
•Cross head screw driver
•Drill with 2mm diameter drill bit
•Tape measure
•Step ladder
x 2 Drill
No. Components Qty.
1Seat back 2
2Seat leg 2
3Left-hand seat 1
4Right-hand seat 1
5Left-hand seat facia rail 1
6Right-hand seat facia rail 1
7Left-hand upright 1
8Right-hand upright 1
9Centre post upper section 1
10 Centre post lower section 1
11 Centre roof rafter support 1
12 Back panel 2
13 Left-hand roof rafter 1
14 Right-hand roof rafter 1
15 Centre roof rafter 1
16 Roof panel 2
17 Front coverstrip 2
18 Left-hand top coverstrip 2
19 Right-hand top coverstrip 2
20 Left finial 1
21 Right finial 1
No. Fixing kit Qty.
22 40mm screws 32
23 60mm screws 24
24 70mm screws 40
25 130mm screws 5
26 150mm screws 2
12
68
5
4
7
11
10
9
13 14
15
16
32
1
17
18
Haven Arbour English SS124C
Assembly Instructions
19
20 21
Biocidal Products Regulation EU 528/2012
Wolmanit CX treated wood is a treated article that
incorporates biocidal products: copper hydroxide
carbonate/II/ and boric acid. They protect wood
against fungal decay /rot/ and insect attack.
Keep away from food, drink and animal feeding stuffs.
Avoid breathing dust when cutting treated wood.

Drill
1. Centre post and seats prep assembly
Join together the upper and lower parts of the centre post using 4 x 60mm screws. Fix a seat leg to the angled end of each seat using 4 x 70mm screws per leg as shown
below. Drill holes in the seat slat bearers as shown below.
Drill
60mm
70mm
Angled end of left-hand seat Angled end of right-hand seat
Note: Ensure that the leg on the left-hand
seat is positioned near the front of the seat
and the leg on the right-hand seat is
Positioned near the back of the seat.
Drill
Drill
left-hand seat Right-hand seat
Drill
360mm 360mm
70mm
Upright
Seat
70mm
3. Seat backs
At each end of the two seat backs drill two holes in the seat back slat bearers as shown. Position each seat back on top of the seats between the uprights and the centre
post. With them flush to the back edge of the uprights and centre post, secure each one using 4 x 70mm screws, screw through the drilled holes of the seat back bearer
into the centre post and leg of the upright.
2. Seats to upright and centre post
Position the left-hand seat against the inside of the left-hand upright, ensure the seat bearer is 360mm from the bottom of the upright and the back edge of the seat is flush
to the back edge of the upright post. Secure in place using 4 x 70 screws, screw through the drilled holes in the seat bearer into the legs of the upright. Attach the seat
fascia rails to the front of the seats using 3 x 40mm screws per fascia. Create the right-hand section in the same way. Attach the left and right section to the centre post.
Ensure the correct orientation of the pre-drilled holes at the top of the centre post (as shown below) and the seat is at the same height as on the uprights and that the
angled ends of the two seats meet evenly. Use 2 x 70mm screw to secure each seat to the centre post.
Centre post
View from back of seat
70mm
40mm
70mm
70mm
Angled ends
of fascia
Hole orientation
70mm
Seat slat bearers
seat back slat bearers

5. Centre roof rafter support
Drill two holes in each upright panel where indicated in the diagram below. Sit the centre support in the rebates of the two uprights and secure using 4 x 60mm screws,
through the drilled holes and into the centre roof rafter support. Drill two holes in each finial where indicated in the diagram. Fit the finials as shown using 2 x 40mm screws
per finial to the centre roof rafter support.
6. Roof rafters
Drill two holes in each upright panel where indicated in the diagram below. Place the roof rafters on top of the back panels make sure the roof bearers face inwards as
shown in the diagram, secure through the drilled holes of the upright into the roof rafters using 2 x 60mm screws per rafter.
DrillDrill
Drill
Drill
Roof rafter
Roof bearer
60mm
40mm
40mm
60mm
60mm
4. Back panels
Position the back panels on top of the seat backs between the uprights and centre post. Secure each one in place using 4 x 70mm screws. Screw through the frame of the
back panel into the uprights.
70mm

7. Centre roof rafter
Fix the centre roof support to the support block using 1 x 130mm screw as shown. Make sure that the back end of the centre roof rafter is touching the centre post and
is at the same height as the outer roof rafters. Secure the outer rafters using 4 x 130mm screws through the holes in the centre post and into the ends of the roof rafters.
Secure the centre rafter in the same way using 2 x 150mm screws.
Drill
Make sure this is at the
same height as the outer
roof rafters and touches
the centre post.
8. Roof panels
Lay the roof panels on the roof rafters and secure using 6 x 60mm screws per panel, screw through the panel and into the roof rafters as shown below.
9. Coverstrips
Drill four holes in each top coverstrip as shown below. Lay cover strips in place and secure with 4 x 40mm screws per strip, screw through the drilled holes of the coverstrip
into the roof panel. Fix the front coverstrips to the ends of the roof panel bearers with 3 x 40mm screws per coverstrip as shown.
Right-hand top coverstrip
Right-hand top
coverstrip
Left-hand top
coverstrip
Left-hand top
coverstrip
Drill
2012 © Rowlinson Garden Products Ltd
We constantly improve the quality of our products,
occasionally the components may differ from the
components shown and are only correct at time of
printing. We reserve the right to change the
specification of our products without prior notice.
If in doubt of any aspect regarding the assembly, use or safety of your swing seat please contact us :
Help Line (Normal Office Hours) 01829 261121
ROWLINSON GARDEN PRODUCTS LIMITED
Green Lane
Wardle Nr.Nantwich
Cheshire
CW5 6BN
130mm
130mm 130mm
150mm
60mm 60mm
40mm
40mm