Rowlinson Garden Products Oriental Pagoda PERGODA2HD User manual

Before assembly
•We recommend that time is taken to read the
instructions before starting assembly, then
follow the easy step by step guide.
The instruction sheet is only a guide to
the assembly. Certain items may not be
shown to scale.
•Check all components prior to assembly
•This product should be assembled by no
less than 2 people.
•Never attempt to erect the assembly in
high winds.
•Drill components where indicated.
x 2 Drill
Oriental Pagoda English SS136A
Assembly Instructions
2187mm
2490mm
Base dimensions

No. Components Qty.
1 Square centre base 1
2 Rectangular bases 6
3 Floor bearers with metal brackets 6
4 Bearer separators 6
5 Floor panels 6
6 Hexagonal centre piece 2
7 Uprights 6
8 Floor edge panels 6
9 Large fences 5
10 Medium fences 6
11 Small fences 6
12 Hand rails 5
13 Long top frames 6
14 Short top frames 6
15 Triangular corner supports 12
16 Left arch piece 6
17 Right arch piece 6
18 Lower roof rafter 6
19 Lower roof rafter support 6
20 Lower roof panels 6
21 Mid roof panels 6
22 Upper roof panels 6
23 Lower roof coverstrips 6
24 Mid roof coverstrips 6
25 Upper roof coverstrips 6
26 Metal roof support ring 1
27 Mid roof bearers 6
28 Mid roof bearer supports 6
29 Upper roof bearers 6
30 Centre finial 1
31 Finials 12
1
2
36
8
5
4
7
9
13 14
15
16 17
18
19 20
21 22
23
24 25
26
27
28
29
30 31
12
11
10
30
31
Components list
No. Fixings Qty.
32 Metal L-brackets 24
33 130mm screws 6
34 70mm screws 255
35 50mm screws 450
36 40mm screws 216
Recommended tools for assembly
•Cross head screw driver
•Sharp knife
•Drill with 4mm diameter drill bit
•Step ladder

1
34
56
7
89
Position floor panels but do not screw down.
Lay out the floor bearers on the bases as shown. Centre of floor bearers resting on squarefloor base.
Add floor bearer separators.
2
Hexagonal floor centre
Uprights are located into the metal brackets.
Secure uprights in place with 4 x 50mm screws.
Attach floor edge panels using 3 x 40mm screwsAll uprights secured in place.
Rectangular bases

10 11
12 13
14 15
16
18
17
Position the medium sized fences as shown.
Shows all large fences in place.
Secure hand rails by screwing through fence into handrail using 3 x 40mm screws.
Secure top frames to upright ends with 4 x 70mm screws per frame.
Sit the large fence on the floor between the uprights and secure with 6 x 70mm screws. It may help to drill pilot holes in the end frames of all the fence.
Position a handrail on top of each fence.
Upright top frames are positioned as shown.
Secure fence with 4 x 50mm screws, 2 at each end of the fence.
Top view of an upright
to show where the top
frames screw in.

19 20
21 22
23 24
25 26
27 28
Drill 2 holes in each of the triangular corner supports. Using 2 x 40mm screws, secure a corner support in each corner.
Attach arches using 2 x 40mm screws per arch.
Screw through the pre-drilled hole of the upright into the roof bearer.
Drill a hole in each end of the lower roof bearer support
Position the lower roof panels between the roof bearers.
Drill 2 holes in each arch piece. Note that there is a left and right angled arch piece.
Secure the lower roof bearer using 1 x 130mm screw per upright.
Shows Lower roof supports in place.
Secure the bearer support as shown using 2 x 50mm screws
Align the roof bearer with the bottom
of the mid sized fence as shown.

29 30
31 32
33 34
35 36
37 38
L-brackets on both side
of of the roof rafter.
Secure in place at each end with 2 x 50mm screws.
Attach roof cover strip using 3 x 40mm screws.
Secure back of roof with 1 x 40mm screw.
Underneath view of roof coverstrip attachment.
Attach 4 long roof bearers to the metal ring. See 34 Attach using 5 x 50mm screws per bearer.
Lift bearer assembly onto uprights and align with the uprights. Secure each bearer in place with 2 L-brackets and 8 x 40mm screws.
Attach the remaining 2 bearers to the metal ring and to the main assembly as before.
Use wide
shank 50mm
screws.
Drill 4 holes in small upright top frames.
View from inside building.

39 40
41 42
43 44
45 46
47 48
Secure small top frames to the top long roof bearers, using 4 x 70mm screws. Shows top frames in position.
Drill a hole in each end of the 6 roof supports. Note the orientation. Secure each roof support with 2 x 50mm screws.
Short end
to upright. Long end to
roof bearer.
Using 2 x 40mm screws, secure a corner support in each corner of the top frame. Shows top frames with corner supports in position.
Centrally attach the 2nd hexagonal piece to the centre finial using 1 x 70mm screw. Drill hole and screw top roof bearers to centre finial using 1 x 70mm screws.
Shows all top roof bearers attached to centre finial. Position bearer assembly centrally onto the top roof frames.

49 50
51 52
53 54
55 56
57 58
L-brackets
Position top fences as shown and secure using 4 x 50mm screws. See Photo 18. Secure top roof bearers to top frame using 2 L-brackets and 8 x 40mm screws per bearer.
Drill 4 holes in the 6 small triangular roof panels. Secure roof panels to the top roof rafters using 4 x 50mm screws per panel.
Fit 6 roof panel facia boards and the 6 finials using 2 x 50mm screws each. Drill 6 holes as shown in the 6 larger triangular roof panels.
Secure the panels on the middle roof bearers using 6 x 50mm screws. Fit 6 roof panel facia boards and the 6 finials using 2 x 50mm screws each.
Secure each floor panel down using 8 x 50mm screws per panel. Secure the floor centre hexagon using 6 x 50mm screws.