Rowlinson Garden Products SS141E User manual

Before assembly
•We recommend that time is taken to
read the instructions before starting
assembly, then follow the easy step
by step guide.The instruction sheet
is only a guide to the assembly.
Certain items may not be shown to
scale.
•Check all components prior to assembly
•This product should be assembled
by no less than two people.
•Never attempt to erect the assembly
in high winds.
•Drill all components where indicated.
Recommended tools for assembly
•Cross head screw driver
•Drill with 3mm diameter drill bit
•13mm Spanner
x 2 Drill
No. Components Qty.
1Seat back 1
2Seat 1
3Left upright 1
4Right upright 1
5Upright top rail 2
6Upright top rail support 2
7Lattice back panel 1
8Roof slat sections 4
9FR/BL* roof rafters 2
10 FL/BR* roof rafters 2
11 Centre roof rafter 2
12 Roof coverstrips 1
13 Finials 2
No. Fixing kit Qty.
14 Metal L-brackets 6
15 70mm screws 8
16 60mm screws 12
17 40mm screws 54
18 100mm Bolts 2
19 Nuts 2
20 Washers 2
1
2
3
4
5
6
7
8
9
10
11
12
40mm
40mm
6. Roof section to uprights
Fix the L-brackets to the uprights using 2 x 40mm screws per bracket. Lift roof onto uprights so that rebates in the
roof rafters rest on the uprights, secure roof to L-bracket using 2 x 40mm screws per bracket.
*FR/BL = Front right/back left
FL/BR = Front left/back right
Caution
When used as a
Barbecue Station, the
barbecue should not be
left unattended.
BBQ Party Arbour
Assembly Instructions
English SS141E
13
14
I MPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
When the side tables are put in the raised position, ensure they are locked in place by turning the turn buttons.
When used as a Barbecue Station, the barbecue should not be left unattended.
Periodically check all fastenings for tightness
For domestic use only
Safety information
2016 © Rowlinson Garden Products Ltd
If in doubt of any aspect regarding the assembly, use or safety of your Arbour please contact us:
Help Line: (Normal Office Hours) 01829 261 121
Email: [e-mail]
ROWLINSON GARDEN PRODUCTS LIMITED
Green Lane
Wardle Nr. Nantwich
Cheshire
CW5 6BN
www.rowgar.co.uk
We constantly improve the quality of our products, occasionally
the components may differ from the components shown and are
only correct at time of printing. We reserve the right to change the
specification of our products without prior notice.

Drill
70mm
70mm
40mm
40mm
40mm
40mm
40mm
40mm
Drill
Drill
1. Seat back to uprights
Drill the back panel as shown in the diagram at both ends. Position back panel between the uprights as shown. Screw
through the drilled holes into the uprights using 4 x 70mm screws.
4. Roof section assembly
Bend two roof slat section and fit it into the rebates of two bearers as shown below. Secure each bearer using
2 x 40mm screws, screw through the top of the bearer into the slats. Position a centre roof rafter in the middle of the
roof section and secure using 2 x 40mm screws, screw through the roof slats into the centre rafter. Create a second
roof section in the same way.
5. Roof assembly
On one roof section attach an L-bracket to the underside of each roof bearer at the apex end using 2 x 40mm screws
per bracket. Evenly rest the second roof section against the first and attach using 2 x 40mm screws through the
L-brackets. Drill 4 holes in each finial. Centre finial so it overlaps both roof bearers and secure using 4 x 40mm screws
per finial. Drill two holes at each end and two in the middle of the cover strip as shown. secure the coverstrip on the
roof ridge using 6 x 40mm screws.
Plywood strips underneath
Roof rebates at the bottom
Apex end of bearers
Fit the L-brackets to the bearer
ends that do not have rebates.
Note: When fitting
centre roof rafter
ensure the angle at the
apex end of the roof
panel matches that of
the two bearers.
3. Seat
Lift the side panels of the uprights and sit the metal supports into the metal brackets on the seat bearers. Position the
seat onto the bearers. From the side of the arbour push 1 x 100mm bolt through each hole at the back of the seat
bearer and seat. Secure with a nut and washer. Secure the other side in the same way.
Top view of
back piece
showing angle
to drill.
445mm 105mm
Front of arbour Back of arbour
60mm
60mm
2. Upright top rails and lattice back panel
For each upright position an upright top rail in to the rebates at the top of the legs as shown. Secure in place using
2 x 60mm screws per leg. secure a top rail support to the underside of the rail and the front leg of the upright using
2 x 60mm screws per support as shown. Place the trellis back piece between the uprights so it rests on the seat back.
Screw from inside of the lattice into the uprights using 2 x 70mm screws at each end.
Drill
It is recommended to drill pilot
holes for these screws with a
4mm drill bit before assembly.
Ensure the rebates at the
top of the upright legs are
facing inwards.
100mm
100mm
For safety, whenever the side
tables are put in the raised
position, always lock them in
place by turning the turn button.
Caution Turn button for locking
tables in raised position.