Rowlinson Garden Products Bondi BBQSHEL User manual

Recommended tools for assembly
•Electric drill/screw driver
•Cross head screwdriver bit
•3mm diameter drill bit
•Spirit level
•Step ladder
No. Components Qty.
1Back leg (90x90x2000mm) 2
2Front leg (90x90x2300mm) 2
3Back panel 1
4Side panel 2
5Front/Rear roof frame (50x45x1820mm) 2
6Roof rafter (50x45x1340mm) 4
7Roof board (15x120x2000mm) 15
8Side barge board (20x120x1470mm) 2
9Front/Rear barge board (20x120x2045mm) 1
10 Side shelf (20x90x1220mm) 4
11 Shelf support blocks (40x30x200mm) 4
No. Fixing kit Qty.
12 Metal L-bracket 6
13 Roof board spacer tool 2
14 Panel height spacer (45x45x150mm) 2
15 100mm screws 20
16 70mm screws 18
17 50mm screws 84
18 20mm screws 24
Bondi Barbecue Shelter English SS574
Assembly Instructions
Biocidal Products Regulation EU 528/2012
Wolmanit CX treated wood is a treated article that
incorporates biocidal products: copper hydroxide
carbonate/II/ and boric acid. They protect wood
against fungal decay /rot/ and insect attack.
Keep away from food, drink and animal feeding
stuffs.
Avoid breathing dust when cutting treated wood.
Before assembly
•We recommend that time is taken to read the
instructions before starting assembly, then
follow the easy step by step guide.
The instruction sheet is only a guide to
the assembly. Certain items may not be
shown to scale.
•Check all components prior to assembly
•This product should be assembled by no
less than two people.
•Never attempt to erect the assembly in
high winds.
•Drill components where indicated.
11
6
8
5
4
7
10 12
13
14
9
3
2
1
x 2
Drill

1. Legs, back and side panels
2. Outer shelf support blocks
Note: To set the panel
height, rest the panel
on the two spacer
blocks provided.
Remove the spacer
block once the panel is
secure to the legs.
Note: To set the panel height, rest
the panel on the two spacer blocks
provided.
Remove the spacer block once the
panel is secure to the legs.
Note: To set the panel height, rest
the panel on the two spacer blocks
provided.
Remove the spacer block once the
panel is secure to the legs.
70mm
2
2
1
1
12
12
12
12
50mm
50mm
70mm
4
14
14
70mm
50mm
50mm
14
14
14
14
3
4

3. Side shelves
4. Roof frame
Roof rafters are
angled at each end,
ensure they are
all orientated the
same way.
At the front of the
structure, ensure
roof is flush with
the top and front
edge of the posts.
At the back of the
structure, ensure
rear roof frame is
flush with the top
and back edge of
the posts.
Roof rafters are
angled at each end,
ensure they are
all orientated the
same way.
50mm
50mm
20mm
11
6
6
6
6
5
5
100mm
70mm
70mm
11
11
20mm
11
100mm
50mm
50mm

6. Barge Boards
5. Roof Boards
Important information - retain for future reference
If in doubt of any aspect regarding the assembly, use or safety of your garden building please contact us:
Help Line: (Normal Office Hours) 01829 261 121
Email: [e-mail]
ROWLINSON GARDEN PRODUCTS LIMITED
Green Lane
Wardle Nr. Nantwich
Cheshire
CW5 6BN
www.rowgar.co.uk
We constantly improve the quality of our products,
occasionally the components may differ from the
components shown and are only correct at time
of printing. We reserve the right to change the
specification of our products without prior notice.
2022 © Rowlinson Garden Products Ltd
Use the two roof board space tools to
consistent spacing of the roof boards.
Continue to adding roof boards
up the roof. Spacing them using
the spacer tools.
Ensure final roof
board is flush to the
front edge of the
legs and roof frame.
Ensure first roof
board is flush to the
back edge of the
legs and roof frame.
7
70mm
70mm
7
14
14
70mm
70mm
8
8
9
970mm
70mm
70mm
70mm
14
14
7
7