Royal Sovereign RSC-820CL User manual

RSC-820CL/CLS Laminator
OWNER'S MANUAL
Royal Sovereign International Inc.
www.royalsovereign.com
Read all instructions carefully before use.
For any Customer Support needs please choose the
Customer Support tab on www.royalsovereign.com

2
TABLE OF CONTENTS
TOPIC PAGE
1. Introduction....................................................................................................... 3
2. Safety Precautions ............................................................................................ 3
3. Installation ......................................................................................................... 4
4. Included with Laminator .................................................................................... 5
5. Product Identification..........................................................................................6
6. Control Panel..................................................................................................... 7
7. Roller Nip Settings............................................................................................. 8
8. Using Foot Pedal................................................................................................9
9. Loading Film...................................................................................................... 9
10.Threading Film
10.1. Decaling........................................................................................... 10-12
10.2. Mounting............................................................................................... 13
11. Maintenance.................................................................................................. 14
12.Troubleshooting ............................................................................................. 14
13. Specifications ................................................................................................ 15
14.Warranty ........................................................................................................ 16

RSC-820CL/CLS
3
1. INTRODUCTION
2. SAFETY PRECAUTIONS
Failure to comply with any of the following safety procedures could result in serious injury.
Please read the instructions carefully and keep for future reference.
1. Only a licensed electrician should install wiring and outlet for the laminator.
2. Ensure the unit is plugged into a properly grounded outlet with the correct voltage.
3. Keep hands and clothing (i.e. Neckties) away from rollers.The rollers have pinch points
that can trap body parts or clothing and cause serious injury.
4. Keep flammable and wet objects away from the machine.
5. Place machine on a level surface.
6. Avoid excessive sunlight, humidity and extreme temperatures.
7. Ensure the unit is turned off, cooled, and unplugged from the outlet prior to moving
and/or repairing.
8. Keep out of reach of children.
9. Only Royal Sovereign authorized maintenance and service technicians should make
repairs.
10. Do not attempt to laminate items that exceed total recommended material thickness
for the unit
11.When cleaning the machine, don't use flammable sprays or materials.
12. Do not touch the rollers when they place foreign objects inside the machine.
Thank you for choosing a Royal Sovereign laminator. It has been designed and
manufactured to provide years of continuous service. For complete operating and
maintenance information please read this manual thoroughly. Upon receipt of your
laminator, please inspect the box, the machine and all other contents for shipping
damage. Damage should be brought to the immediate attention of the delivering carrier
(See page 5 for list of shipment elements).

4
MODEL RSC-820CL/CLS
Power Supply
220-240V 120V 220-240V 120V
50/60HZ 50/60HZ 50/60HZ 50/60HZ
single phase
3. INSTALLATION
Note: The laminator should be installed by a trained service technician.
ELECTRICAL REQUIREMENTS
The laminator comes fully assembled, except for the stand to avoid shipping damage.
Upon arrival, thoroughly inspect the unit. It is imperative that any shipping damage is
reported and a claim is filed with the delivering carrier immediately upon receipt.
The laminator should be located in an area with adequate work space for feeding
graphics and lamination materials.
Avoid placing the laminator in a dusty area or near sources of extreme heat or cold.
Once the laminator is in place, lock the casters into position(“ON” position). Always
unlock the casters (“OFF” position) when moving to a different location.
Royal Sovereign recommends that a licensed electrician ensures proper power
installation to your laminator in accordance with electrical codes in your area.
The laminator should have a dedicated power line.
230V UL
120V UL
220V EU
240V UK
220V AU

RSC-820CL/CLS
5
4. INCLUDED WITH LAMINATOR
Thoroughly inspect the parts and the unit. It is imperative that any missing parts are
reported and a claim is filed with the reseller immediately upon receipt of shipment.
Part Name
Laminator
Owner's Manual
Dust Cover
Spare Motor Fuse - FUSE(50T)
(6.3A)
Spare Main Power Fuse - FUSE(65TS)
(5A)
1
1
1
1
1
Quantity Picture
3´´(76mm) Auto Grip 6/6

6
5. PRODUCT IDENTIFICATION
1
8
2
3
7
5
4
10
7
9
NO. PART NAME RSC-820CL/CLS
1 SAFETY COVER O
2 FEED TABLE O
3 MAIN ROLLER O
4 FOOT PEDAL O
5 TENSION CONTROL KNOBS O
6 PRESSURE LEVER O
7 CONTROL PANEL O
8 UPPER IDLE BAR O
9 RELEASE LINER TAKE UP O
10 STAND O

RSC-820CL/CLS
7
6. CONTROL PANEL
When the machine is initially turned on, the LED display window will show the speed at 1.
Control Buttons
1. SPEED DISPLAY: Display’s current Speed.
2. SPEED BUTTON: Adjusting the speed of the rollers. To change the speed of the rollers,
press the up or down arrow button.
3. RUN: To start the rollers.
4. STOP: To stop the rollers.
5. REV: To reverse the rollers, press and hold the REVERSE button.
1
2
3
4
5

8
7. ROLLER NIP SETTING
It is important to adjust the roller nip settings to the appropriate thickness of the board
being used. Use the guide below to adjust to the correct position.
NO. Inches Metric
(mm)
1 Laminating Laminating
2 0.12" 3
3 0.2" 5
4 0.27" 7
5 OPEN OPEN
NOTE: If you don't want to laminate,please place the pressure lever to the
"Open position(NO.5)".
1
2
3
4
5

RSC-820CL/CLS
9
8. USING FOOT PEDAL
USING FOOT PEDAL
Place the foot pedal on the floor in front of the
machine. Once all correct settings are displayed,
you may use the foot pedal to operate the laminator
for “Hands Free Operation.” To activate the machine,
press the foot pedal once and then release. Repeat
to stop the rollers.
9. LOADING FILM
The cross cutter is located on the rear exit table of the machine.
1. After lamination, move the cutter approximately to the
center of the completed application at the desired
point of detachment (Figure 1).
2. Grasp film with one hand, press the cutter
downward into the application and slide it first to
one end of the application, then to the other end to
complete the cut (Figure 2 & 3).
Figure 1
Figure 2
Figure 3

10
1.Turn the power switch on (“I” position).The Power switch is located on the rear left side
of the unit.
2.Complete the steps as in the “LOADING FILM” section (see page 10).
3.Take off the FeedTable.
4.Pull the top film down over the Safety Cover to the bottom of the craft paper/mounting
film.
10. THREADING FILM
10.1. Decaling
Figure 1
TVQQPSU!JEMF!CBS
5. Align and center the craft paper/mounting film to the top
film and tighten the two lower core screws (Figure 1).