Royal Sovereign RSL2701S User manual

TABLE TOP LAMINATOR
RSL-2701S OWNER’S MANUAL
Please read instructions carefully before use.

2
TABLE OF CONTENTS
▣Introduction ----------------------------------------------------------------------------------- 3
▣Package Contents --------------------------------------------------------------------------- 3
▣Safety Precautions --------------------------------------------------------------------------- 4
▣Parts -------------------------------------------------------------------------------------------- 5
▣Features Guide ------------------------------------------------------------------------------- 6
▣Operating Instructions -------------------------------------------------------------------- 9
▣Film Loading and Threading ------------------------------------------------------------ 10
▣Maintenance --------------------------------------------------------------------------------- 12
▣Trouble shooting guide ------------------------------------------------------------------- 13
▣Specifications ------------------------------------------------------------------------------- 14
▣Warranty ----------------------------------------------------------------------------------- 15

INTRODUCTION
Thank you for purchasing RSL-2701S Table Top Laminator. It has been
designed and manufactured to provide years of continuous service. For
high quality lamination, please read this instruction manual thoroughly.
This manual will provide you with complete operating and maintenance
information.
PACKAGE CONTENTS
Preloaded Roll Films
(635mm x 75mic x 30m)
(
25in x 3mil x 98.4ft
)
SPARE FUSE
(250V / 15A)
RSL-2701S
Owner's
Manual
3

SAFETY PRECAUTIONS
WARNING
Failure to comply with any of the following safety procedures could result in serious
injury.
1. Insure the unit is plugged into a properly grounded outlet with the correct voltage.
2. Only licenses electricians should service or repair the electrical wiring.
3. Keep flammable and wet objects away from the machine.
4. Place machine on a level sturdy surface.
5. Avoid excessive sunlight, humidity and temperatures.
6. Unplug the machine when moving it or when it's not in use.
7. Keep out of reach of children.
8. Only authorized maintenance and service technician are permitted to make repairs.
9. Do not cover the surface of the machine until the machine is completely cooled.
10. When cleaning the machine, don't use flammable sprays or materials.
11. Do not touch the rollers or allow foreign objects inside the machine.
12. You can laminate by single film when the switch in the left cover is “O”.
( Insure the machine drastically cold, press the button in the left cover be “ O ”,then
you can laminate by single side. It is a damage for the paper to laminate by single side
while the rollers up and low are heating all together.)
4

PARTS
5
③
①
④
②
⑤
⑥
⑦
⑧
○
10
⑨
1- Upper Film
2- Lower Film
3- Idle Bar
4- Hot Rollers
5- Feed Table
6- Paper Guide
7- Control Panel
8- Tension Knob
9- Power Switch
10- Single/Double Laminating Switch “O” (on) “I” (off).

FEATURES GUIDE-1
Figure 1
Run and stop the machine
Reverse the rollers to undo jams
and correct misfed documents
Reduce roller speed
(
1~10 s
p
eed settin
g
s
)
Increase roller speed
(
1~10 s
p
eed settin
g
s
)
Film Application Thickness
125mic
Film Application Thickness
50mic
~
100mic
Film Application Thickness
25mic
~
38mic
25mic~38mic
50mic~100mic
125mic
RUN/STOP
REVERSE
DOWN
UP
1
2
3
125 mic
SPEED
25~38 mic
4
5
6
7
50~100 mic
8
9
10
RSL- 2701
RSL-2701S
6

FEATURES GUIDE-2
Run and stop the machine
Reverse the rollers to undo jams
and correct misfed documents
Reduce roller speed
(
1~10 s
p
eed settin
g
s
)
Increase roller speed
(
1~10 s
p
eed settin
g
s
)
Film Application Tem
210° F~230° F
perature
Film Application Tem
230° F~270° F
7
210° F~230° F
perature
Film Application Tem
270° F~310° F
230° F~270° F
perature
270° F~310° F
Figure 1

Power Switch (1) - Located on the rear of
8
the machine. “I” (on) “0” (off). (Fig. 2)
Cross Cutter (2) - Used to cut off the
laminated web. (Fig. 2)
Figure 2
①②
Feed Guide (3) –The feed guide permits
alignment of the item(s) to be laminated. To
position the adjustable guide, loosen the knob,
slide it to the desired position and tighten the
knob to secure the feed guide in place. (Fig.3)
Safety Shield (4) – It prevents entanglement
NOTE: If the safety shield is opened, the power
to the motor will turn off.
Figure 3
③
④
Film Shaft and Locking
Core Adapter (5) –
The film shaft holds the film supply on the
machine. The locking core holds and locks the
film on the shaft to prevent shifting. (Fig.4)
Figure 4
Film Tension Adjustment (6) – Allows the
operator to increase or decrease film web
tension. To increase the tension turn the knob
clockwise and to decrease tension turn the
knob counterclockwise. (Fig. 5)
Figure 5

9
OPERATING INSTRUCTION
1. Turn the laminator ON (I) located on the rear of the machine. (Fig. 2)
2. Choose appropriate laminating thickness and speed. (Fig. 1)
3. Do not begin laminating until the blinking light is steady (approximately 8 minutes).
4. Position the item to be laminated on the feed table.
5. Press the RUN button. The rollers will begin to turn, wait for heat line to disappear,
feed the item into the machine.
6. Insure the machine drastically cold, press the button in the left cover be “ O ”,then
you can laminate by single side.(It is a damage for the paper to laminate by single
side while the rollers up and low are heating all together.)
7. Stop the laminator when all of the items have completely exited the rear of the
machine.
8. Please loose the film tension as loosed as possible.
9. If there the temperature is high while laminating by some films with thin paper on the
middle temperature level that you can use the low temperature level.
Repeat the above steps until all of your lamination is completed. When lamination is
completed the machine is not in use for an extended period of time turn the power off.
NOTE: Stand by mode and auto power off mode
- Stand by mode: If no activity is made within 30 minutes after each use the
machine will automatically switch into stand by mode. (In stand-by mode the
temperature will decrease to 80~90 and the three film thickness setting℃
indicators will blink).
- Auto power off mode: If the machine is in stand by mode and no activity is
made for 60 minutes the machine will automatically power off.
- If any activity is made while in stand by or auto power off mode the machine
will return to it’s previous stage.

Idler bar
FILM LOADING & THREADING
10
Upper
roll film
Lower
roll film
Roller
Idler bar
Laminating
direction
Figure 6
▲LOADING UPPER ROLL FILM
1. Slightly slide the shaft to the right and
pull it out from the machine.
Figure 7
2. Take both lock core adapters off
from the shaft.