RS PRO ICM A5 User manual

Instruction Manual
ICM A5
Clamp Meter
EN DE ES IT FR


EN - 2
Safety Information
Read and understand this Instruction
Manual completely before using this
instrument. Failure to observe the warnings
and cautions in this Instruction Manual may
result in injury or death, or damage to the
instrument and other equipment or
property.
If this instrument is used in a manner not
specified in these instructions, the protec-
tion provided by the instrument may be
impaired.
WARNING
-Examine the instrument and probes and
leads before use. Do not use the instru-
ment if it is wet or damaged, or if you
suspect it is not operating correctly.
-When using the instrument, test leads or
probes, keep your fingers behind the
finger guards.
-Remove the test lead from the instrument
before opening the battery cover or instru-
ment case.
-Always use the correct terminals, switch
position and range for measurements.
-Verify the instrument is operating correctly
by measuring a known voltage before
use. If in doubt, have the instrument
serviced.
-Do not apply more than the rated voltage
as marked on the instrument between
terminals, or between any terminal and
earth ground.
-Use caution when measuring voltages
above 30 Vac rms or 60 Vdc. These
voltages pose a shock hazard.
-To avoid incorrect readings that can lead
to electric shock, replace the battery as
soon as low battery indicator appears
in the display.
-Disconnect the circuit power and
discharge all high-voltage capacitors
before making resistance, continuity, or
diode measurements.

EN - 3
-Do not use the instrument in a Hazardous
Area or around explosive gasses or
vapours.
-Wear suitable Personal Protective
Equipment when working around or near
hazardous Live conductors which could
be accessible.
Caution
-Disconnect the test leads from the test
points before changing the position of the
function rotary switch.
-Never connect the instrument to a source
of voltage with the function rotary switch in
Ω/ ;/Aposition.
- If possible, do not work alone, so
assistance can be given if required.
-Do not expose the instrument to extremes
of temperature or high humidity.
The following symbols may appear on
the instrument and in this Instruction
Manual:
Risk of electric shock
Refer to Instruction Manual
Alternating Current (ac)
<Battery
Earth
Equipment protected throughout by
double or reinforced insulation
Conforms to EU directives
Dispose of this equipment in
accordance with local regulations.
EApplication around and removal
from hazardous Live conductors is
permitted.

EN - 4
Maintenance
Do not attempt to repair this Instrument. It
contains no user-serviceable parts. Repair
or servicing should only be performed by
qualified personnel. This instrument
should be calibrated yearly, or more
frequently if used in harsh conditions or if
it is suspected of being inaccurate.
For calibration and repair contact RS
Components - the address is given at the
end of these instructions.
Cleaning
Periodically wipe the case with a damp
cloth and detergent. Do not use abrasives
or solvents.

EN - 5
Power On / Off
Auto Power Off
The instrument will automatically turn off
approximately 10 minutes after the last
operation.
AC V / DC V

EN - 6
Data Hold
Non-Contact Voltage Sensing:
VoltSenseTM
1. The VoltSense function will operate
irrespective of the position of the
function rotary switch, including the
OFF position.
2. Remove the test leads from the
instrument as they are not used for the
VoltSense test.
3. Press and hold the VoltSense button.
The LCD display will go blank, a tone will
sound and the red LED will illuminate
momentarily to confirm the instrument is
operational.

EN - 7
4. Hold the Volt sense button down and
move the instrument over the area
where detection is required. The buzzer
will sound and the LED will illuminate
when a live conductor is detected.
Release the VoltSense button to return
to normal operation.
Diode / Continuity

EN - 8
ACA
Resistance
CAT.Ⅳ.600V
with respect to
earth for the jaw.
Tactile Barrier for
hand guard.
Do not hold
the meter across
the Tactile Barrier.

EN - 9
Battery Replacement
When the low battery indicator "<"
appears on the LCD, replace the batteries
with the type given in the specifications.
WARNING
Disconnect the test leads from the circuit
and the instrument before removing the
battery cover.
Refer to the following figure to replace the
batteries:

EN - 10
Specifications
1-1 General Specifications
LCD display :
31/2digit large scale LCD readout.
Display resolution : 2000 counts.
Measuring rate : 1.5 times / sec.
Overrange display :
“OL” is displayed for “Ω” functions,
The real value is shown for the “A” and “V”
functions.
Automatic power off time :
Approximately 10 minutes after power on.
Low battery indicator : <is displayed.
Power requirement : 1.5V x 2 batteries
Battery life : Approximately 250 hours with
Alkaline batteries.
1-2 Environmental Conditions
Indoor use only.
Calibration : One year calibration cycle.
Operating temperature :
0°C to 30°C (32°F to 86°F) @ ≦80% RH
30°C to 40°C (86°F to104°F) @≦75% RH)
40°C to 50°C (104°F to 122°F) ≦45%RH
Storage temperature : -20 to + 60°C
(-4°F to 140°F) @ 0 to 80% RH with
batteries removed from the instrument.
Dimensions (W x H x D) :
54mm x 193mm x 31mm
Weight: 280g including battery.
Accessories: Battery (installed), Carrying
case and User manual.
Measurement Category (Installation
Category) :
per IEC 61010-1:2001: CAT.Ⅲ1000V.
CAT.Ⅳ600V. Pollution Degree 2
Measurement Category l is for measure-
ments performed on circuits not directly
connected to mains. Examples include :
Measurements on battery powered equip-
ment and specially protected (internal)
mains-derived circuits.