RS PRO RS-1361C User manual

RS Stock No.712-6045
Instruction Manual
RS-1361C
Humidity / Temperature Meter
Datalogger with RS-232 to USB Interface
FREN IT DE ES
RS - 232
HUMIDITY = 10 ~ 95 %RH
- 4 F ~ 140 F
TEMP = - 20 C ~ 60 C
°
°
°
°

TABLE OF CONTENTS / EN
10/15/10 Version No. 00
TABLE OF CONTENTS
TITLE PAGE
1. INTRODUCTION ........................................................1
2. SPECIFICATIONS......................................................2
3. FRONT PANEL LAYOUT ..........................................4
4. LCD DISPLAY LAYOUT............................................6
5. OPERATING INSTRUCTIONS ..................................7
6. DATA RECORDING AND ERASING.........................8
7. EXIT AUTO POWER OFF FUNCTION....................10
8. MAINTENANCE .......................................................11

INTRODUCTION / EN
10/15/10 Version No. 00 EN-1
1.INTRODUCTION
 Read the following information carefully before
attempting to operate or service the meter.
Environmental conditions:
Altitude; 2000 meters max.
Relatively humidity; 95% max.
Operating temperature; 0 to 60°C
Indoor use only.
Complies with EMC Directive 89/336/EEC

SPECIFICATIONS / EN
EN-2 10/15/10 Version No. 00
2.SPECIFICATIONS
Measurement range: Humidity; 10% to 95% RH
Temperature: -20 to +60°C,
-4 to +140°F
Resolution: 0.1% RH, 0.1°C, 0.1°F
Accuracy (after calibration):
Humidity; 3%RH (at 25°C, 30 to 95% RH).
5%RH (at 25°C, 10 to 30% RH).
Temperature; 0.8°C, 1.5°F
Sensor Type: Humidity; Precision capacitance sensor.
Temperature; Semiconductor sensor.
Response time: Humidity; 45% RH to 95% RH <=3 min.
95% RH to 45% RH <= 5 min.
Temperature: 1°C / 2 seconds.
Sampling Rate: 1 sample/second.
Memory Capacity: 7900 data records, with total of
255 sets of results.
Logging interval: Adjustable between 1 and 65,535 seconds.
Auto power off : 30 minutes (can be changed by PC
software).

SPECIFICATIONS / EN
10/15/10 Version No. 00 EN-3
Operatingtemperature&humidity: 0 to 60°C, below 95%RH.
Storage temperature & humidity:-10to 60°C, below70%RH.
Power supply: Qty 1 x 9V Battery type 006P 9V, or
IEC 6F22, or NEDA 1604.
Battery life: Approximately 100 hours.
Dimensions: 270x68x25mm
Accessories: Instruction manual, Battery, Carry case,
RS-232 to USB cable, Data download
software.

FRONT PANEL LAYOUT / EN
EN-4 10/15/10 Version No. 00
3.FRONT PANEL LAYOUT
OPEN
RS - 232
HUMIDITY = 10 ~ 95 %RH
- 4 F ~ 140 F
TEMP = - 20 C ~ 60 C
°
°
°
°

FRONT PANEL LAYOUT / EN
10/15/10 Version No. 00 EN-5
Humidity & Temp. sensor cap
Display
Power ON/OFF & HOLD function switch.
Measurement units select switch.
LCD main display and secondary display
Data RECORD button
RS-232 to USB socket (3.5mm jack)
TX
RX GND
Battery cover

LCD DISPLAY LAYOUT / EN
EN-6 10/15/10 Version No. 00
4.LCD DISPLAY LAYOUT
Minus
Measuring value (main display)
Time information
Measured value (secondary display)
Units “%RH”
Unit “°C, °F”
Memory full indicator
Data recording indicator
Hold function indicator
Low-battery indicator

OPERATING INSTRUCTIONS / EN
10/15/10 Version No. 00 EN-7
5.OPERATING INSTRUCTIONS
Push the power switch to the “ON” position.
Set units to °C or °F as required.
Change to main display or secondary display as required.
The humidity and temperature values will be
displayed.

DATA RECORDING AND ERASING / EN
EN-8 10/15/10 Version No. 00
6.DATA RECORDING AND ERASING
To record one set of data:
To record data continuously:
 Press the “RECORD” button
once.
 The “RECORD” will be
displayed on the LCD
screen for about 0.5 seconds.
 Press and hold the
“RECORD” button for 3
seconds and “RECORD”
will flash once per second.