Rugged Computing WARRIOR Y120 Quick start guide
&
Assembly Instructions
OWNER’S MANUAL
Y120-121217
SKU# Y120
STRENGTH & FITNESS
WARRIOR
HALF RACK
Warning, Safety & Maintenance
2
Be sure that all users carefully read and understand all
warning, safety and maintenance labels on the machine
before each use. Failure to do so may result in death or
serious injury.
It is imperative that you retain this Owner’s Manual and be
sure all warning labels are legible and intact. Replacement
Owner’s Manuals and warning labels are available from
Rugged Fitness.
If you have any questions about the operation, set up or
maintenance of this machine please call our customer service
department at 1 (800) 556-3113.
Table of Contents
3
Important Safety Instructions
4
Il est conseille de subir un examen medical complet avant d’entreprendre tout programme d’exercise.
Si vous avez des etourdissements ou des faiblesses, arretez les exercices immediatement.
Antes de comenzar cualquier programma de ejercicios, deberias tener un examen sico con su doctor.
When using exercise equipment, you
should always take basic precautions,
including the following:
m
m Do not remove any safety labels from the
machine.
m
m
m
m
m
m
m
m
m
m
m
Personal Safety During Assembly
m
m
m
RUGGED FITNESS HALF
RACK.
1-800-556-3113
Obtaining Service
Toll Free: 1-800-556-3113
Phone: 1-708-427-3555
Fax: 1-708-427-3556
Hours: M-F 8:30-5:00 CST
E-Mail: service@ruggedtness.com
Or write to: Rugged Fitness
Service Department
1900 S. Des Plaines Ave.
Forest Park, IL 60130 USA
Retain this Owner’s Manual for future
reference. If you need to order replacement
parts please be prepared to provide the
following information when contacting us so
that we can assist you better.
1. Model Number
2. Place of Purchase
3. Serial Number (S/N)
4. Part # and Description
Preparation
5
-
-
Required Tools
Y120
m
m
m
Installation Requirements
Y120Y120
Fill out and mail the warranty card
Assembly Tips
Y120
NOTE:
CAUTION:
45
6
Y120 Hardware Illustration
7
Y120 Hardware Illustration
45
8
Y120 Parts & Hardware List
Part# Qty Description
45
9
Parts Illustration
45
10
Parts Illustration
45
11
Parts Illustration
12
STEP
1
Be careful to assemble all components
in the sequence they are presented.
NOTE:
Finger tighten all hardware in this step. DO NOT wrench tighten until instructed.
Some components may be pre-assembled. Nylon lock nuts will not fully screw onto
bolts, they must be wrench tightened to fully go on.
1A. (A) (N)
(#3) M16x110mm Hex Head Bolt, QTY 4
(#4) M16 Regular O.D. Washer, QTY 8
(#6) M16 Nylon Lock Nut, QTY 4
1B. (A) (F)
(#11) M16x100mm Hex Head Bolt, QTY 4
(#4) M16 Regular O.D. Washer, QTY 8
(#6) M16 Nylon Lock Nut, QTY 4
STEP
1
13
Front of
Rack
Back of
Rack
14
STEP
2
Be careful to assemble all components
in the sequence they are presented.
NOTE:
Finger tighten all hardware rst in this step. Wrench tighten ALL hardware at the end of
STEP 2C. Some components may be pre-assembled. Nylon lock nuts will not fully screw
onto bolts, they must be wrench tighten to fully go on.
2A. (C & M) (A)
(#3) M16x110mm Hex Head Bolt, QTY 4
(#4) M16 Regular O.D. Washer, QTY 8
(#6) M16 Nylon Lock Nut, QTY 4
NOTE:
1) Please refer to the drawing for the correct bolt hole locations. The bolt
holes are the 12th and 15th holes from the front of the Base Frame for the
Steel Brackets (C & M).
2B. (C & M) (D)
(#2) M16x90mm Hex Head Bolt, QTY 4
(#4) M16 Regular O.D. Washer, QTY 8
(#6) M16 Nylon Lock Nut, QTY 4
2C. (E)(D)
4 - (#1) M16x80mm Hex Head Bolt, QTY 4
4 - (#4) M16 Regular O.D. Washer, QTY 4
4 - (#5) M16 Large O.D. Washer, QTY 4
4 - (#6) M16 Nylon Lock Nut, QTY 4
STEP
2
15
Note 1:
Front of
Rack
Back of
Rack
16
STEP
3
Be careful to assemble all components
in the sequence they are presented.
NOTE:
Some components may be pre-assembled. Nylon lock nuts will not fully screw onto bolts,
they must be wrench tighten to fully go on.
Adjustable J Cups and Spotter Arms
3A. (K & L)(D)
3B. (G & H)(D)
3C. (J)
(H & G).
NOTE:
1)SECURELYanchorthemachinetotheoorusingtheanchorholes
provided.Please consult a professional contractor for the actual anchoring
of the machine.
STEP
3
17
Anchor Hole
Front of
Rack
Back of
Rack
Anchor Hole
Anchor Hole
45
20
Notes
21
Y120 Exploded View
Y120
STRENGTH & FITNESS
Other Rugged Computing Fitness Equipment manuals
Popular Fitness Equipment manuals by other brands
TKO
TKO 6000 owner's manual
TAG
TAG S-Line 756 manual
Domyos
Domyos HOME GYM COMPACT user manual
Goalsetter Systems
Goalsetter Systems GS Wall Mount Installation & owner's instructions
Bodytastic
Bodytastic SpinTastic II PRO Service manual
Christopeit Sport
Christopeit Sport VIBRO 3000 Assembly and exercise instructions
