Ruijie Networks RG-AP630 CD User manual

RG-AP630 (CD) Wireless Access Point
Quick Installation Guide

Copyright Statement
Ruijie Networks©2017
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification,
transmission, translation or commercial use of this document or any portion of this document, in any form or by any means,
without the prior written consent of Ruijie Networks is prohibited.
Exemption Statement
This document is provided “as is”. The contents of this document are subject to change without any notice. Please obtain
the latest information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content accuracy and will
not shoulder any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

Preface
Thank you for using our products. This manual will guide you through the installation of the device.
This manual describes the functional and physical features and provides the device installation steps, hardware
troubleshooting, module technical specifications, and specifications and usage guidelines for cables and connectors.
Audience
It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it
is assumed that the users are already familiar with the related terms and concepts.
Obtaining Technical Assistance
Ruijie Networks Website: http://www.ruijienetworks.com/
Service Email: [email protected]
Technical Support: http://www.ruijienetworks.com/service.aspx
Technical Support Hotline: [phone]
Related Documents
Documents
Description
Configuration Guide
Describes network protocols and related mechanisms that supported by the
product, with configuration examples.
Command Reference
Describes the related configuration commands, including command modes,
parameter descriptions, usage guides, and related examples.
Symbol Conventions
Means reader take note. Notes contain helpful suggestions or references.
Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of
data.

RG-AP630(CD) Wireless Access Point Quick Installation Guide
1 Packing List
Name
Quantity
Unit
Host
1
Set
Mounting plate
1
Piece
Mounting bracket
1
Piece
Tie rod
1
Piece
M8x20 screw with spring and flat washers
4
Piece
M8x40 screw with spring and flat washers
2
Piece
Liquid-light adapter
1
Piece
Grounding cable
1
Piece
Hose clamp
2
Piece
Product Warranty Manual
1
Copy
RG-AP630 (CD) Wireless Access Point Quick Installation
Guide
1
Copy
2 Accessories
3 Product Appearance
Product Appearance of RG-AP630 (CD)

RG-AP630(CD) Wireless Access Point Quick Installation Guide
Note: 1. Console port 3. 10/100/1000 Base-T auto-sensing Ethernet/PoE IN port 4. SFP combo port
4 Installation Tools
The tool kit is customer supplied.

RG-AP630(CD) Wireless Access Point Quick Installation Guide
5 LEDs
LED
State
Meaning
System status
Blinking green
Initialization in progress
Solid yellow
Initialization is complete, but no CAPWAP connection.
Solid green
Initialization is complete, and a CAPWAP connection is
established.
Solid red
Warnings
WDS RSSI (3 LEDs)
1 solid on
< -70dBm
2 solid on
-70 to -50 dBm
3 solid on
> -50 dBm
6 Mounting the AP to the Pole
Attach the mounting bracket to a pole with a hose clamp.

RG-AP630(CD) Wireless Access Point Quick Installation Guide
Attach the mounting plate to the bottom of the AP and fasten the plate with the four M8x20 screws.
Attach the tie rod to the mounting plate and fasten the rod with the M8x40 screws after AP is well-positioned, shown in the
following figure.
Attach the mounting plate to the mounting bracket through the rod with the M8x40 screws, adjust AP orientation, and
tighten the screws on the rod with the Phillips screwdriver (or the wrench).
Horizontal pole mount is also supported. The procedure of horizontal pole mount is similar as that of vertical mount.
7 Mounting the AP on the Wall
Attach the mounting bracket to the wall with user-supplied expansion screws. M8 x 60 screws are recommended.

RG-AP630(CD) Wireless Access Point Quick Installation Guide
Mark the locations of the four screw holes by using the marker. Drill four 8 mm diameter holes. Tap expansion anchors into
the holes, and drive screws through the mounting bracket into the anchors to fix the bracket.
Attach the tie rod to the mounting plate and fix the rod with the supplied M8x40 screws. Adjust the AP orientation, and
drive the two-side screws on the rod.
8 Connecting the Fiber Cable
Insert the SFP module into the SFP port, and then insert the fiber cable with a liquid-tight adapter into the module.

RG-AP630(CD) Wireless Access Point Quick Installation Guide
Before insertion, make sure the nut of the liquid-tight adapter is in loose state. Tighten the liquid-tight adapter and the nut
on the AP first, and then that of the liquid-tight adapter.
9 Connecting the Network Cable
Thread the original network cable through the liquid-tight adapter.
Attach the plug into one end of the network cable nearest to the head of the liquid-light adapter.
Insert the plug into the PoE IN port, and tighten the liquid-tight adapter.
Make sure the plug is correctly inserted. The plug gets damaged when the liquid-tight adapter is wrenched
improperly. Before removing the network cable, dismantle the liquid-tight adapter first and then the plug.
10 Connecting the Grounding Cable
Make sure the AP and the power source share the common ground points.
A lightning arrester is integrated into the AP. In general, no additional lightening arrester is required. If there is higher
requirement for lightening protection, you can purchase it on your own.
The grounding cable is made on site. Connect the supplied grounding wire (yellow-green) to the AP grounding connector
on one end and ground the wire on the other end through OT terminals.

RG-AP630(CD) Wireless Access Point Quick Installation Guide
11 Installing the Security Lock (Optional)
The security lock is user-supplied.
The lock loop on the AP is for your security needs. You can fasten the AP to a fixture for anti-theft. First, fasten the cable
of a security lock to a fixture. Second, secure the lock plate into the lock loop.