Ruijie Reyee RG-EST310 Installation and operating manual

Ruijie Reyee RG-EST310 V2
Wireless Bridge
Hardware Installation and Reference Guide
Document Version: V1.0
Date: 2021.9.16
Copyright © 2022 Ruijie Networks

Copyright
Copyright © 2022 Ruijie Networks
All rights are reserved in this document and this statement.
Any reproduction, excerption, backup, modification, transmission, translation or commercial use of this
document or any portion of this document, in any form or by any means, without the prior written consent of
Ruijie Networks is prohibited.
Trademarks including , , are
owned by Ruijie Networks.
All other trademarks or registered trademarks mentioned in this document are owned by their respective
owners.
Disclaimer
The products, services or features you purchase are subject to commercial contracts and terms. Some or all of
the products, services or features described in this document may not be within the scope of your purchase or
use. Unless otherwise agreed in the contract, Ruijie Networks does not make any express or implied statement
or guarantee for the content of this document.
Due to product version upgrades or other reasons, the content of this document will be updated from time to
time. Ruijie Networks reserves the right to modify the content of the document without any notice or prompt.
This manual is for reference only. Ruijie Networks endeavors to ensure content accuracy and will not shoulder
any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

I
Preface
Intended Audience
This document is intended for:
⚫Network engineers
⚫Technical support and servicing engineers
⚫Network administrators
Technical Support
⚫The official website of Ruijie Reyee: https://www.ruijienetworks.com/products/reyee
Conventions
1. Signs
The signs used in this document are described as below:
Danger
An alert that calls attention to safety operation instructions that if not understood or followed when operating the
device can result in physical injury.
Warning
An alert that calls attention to important rules and information that if not understood or followed can result in
data loss or equipment damage.
Caution
An alert that calls attention to essential information that if not understood or followed can result in function
failure or performance degradation.
Note
An alert that contains additional or supplementary information that if not understood or followed will not lead to
serious consequences.
Specification
An alert that contains a description of product or version support.
2. Note
This manual provides the device installation steps, hardware troubleshooting, module technical specifications,
and specifications and usage guidelines for cables and connectors. It is intended for the users who have some
experience in installing and maintaining network hardware. At the same time, it is assumed that the users are
already familiar with the related terms and concepts.

Hardware Installation and Reference Guide 1 Product Overview
1
1 Product Overview
1.1 RG-EST310 V2
The RG-EST310 V2 is an 802.11ac wireless bridge launched by Ruijie Reyee. It provides services such as
surveillance video backhaul and wireless remote transmission in elevators, tower cranes, factories, parks,
construction sites and other scenarios. RG-EST310 V2 works in the 5GHz frequency band, supports two spatial
streams and 2 x 2 MIMO, and provides a wireless transmission speed of up to 867Mbps, which is sufficient to
meet the bandwidth requirements of user services for data links.
1.2 Package Contents
Table 1-1 Package Contents
No.
Item
Quantity
1
RG-EST310 V2 (Network Video Recorder Side)
1
2
RG-EST310 V2 (Camera Side)
1
3
24 V/0.6 A Non-Standard PoE Adapter
2
4
Bracket
2
5
Hardware Installation and Reference Guide
1
6
Hose Clamp
4
7
Wall Anchor and Self-Tapping Screw
4
Note
●A normal delivery should contain the above mentioned items, which may differ from the actual delivery,
depending on purchase contracts. Please check your goods carefully against the Package Contents or
purchase contract. If you have any questions or there are any errors, please contact your distributor.
1.3 Appearance
Figure 1-1 Appearance
Front View

Hardware Installation and Reference Guide 1 Product Overview
2
Rear View

Hardware Installation and Reference Guide 1 Product Overview
3
1.3.1 Port & Button
Figure 1-2 Port & Button
Note
1. 12 VDC Port
2. 10/100Base-T Ethernet Port (PoE-capable)
3. Reset button
1.3.2 Power Supply
RG-EST310 V2 adopts 12 V/1 A DC or 24 V non-standard PoE power supply. The device is delivered with a 24
V/0.5A power adapter.
Caution
●Please do not use a switch or a PoE adapter of another model for power supply. Otherwise, the device
may be damaged.
Table 1-2 LED Description
LED
Status
Description
System Status
LED
Off
System is not powered on.
Solid On
Initiation process is complete.
Slow Blinking
System is working but there is an alert.
Fast Blinking
System is being initialized.
Port Status LED
Solid On
The LAN port is not receiving or transmitting data.
Blinking
The LAN port is receiving or transmitting data.
Signal LED
LED 1 is solid on.
-73 dBm< RSSI <-59 dBm
LED 1 and LED 2
are solid on.
RSSI > -59 dBm
LED 1, LED 2 and
LED 3 are solid on.
RSSI > -49 dBm
Off
There is no signal.

Hardware Installation and Reference Guide 1 Product Overview
4
Table 1-3 Reset Button Description
Button
Function
Operation
Reset
Reboot
Press the button for 2 seconds, and the device will be
rebooted.
Reset
Press the button for over 5 seconds, and the device will be
reset.
No Action
Press the button for 2 to 5 seconds.
1.4 Device Specification
Table 1-4 Specification
Radio Design
Single-Frequency Dual-Stream
Transmission
Protocol
802.11 a/n/ac
Operating Frequency
5G
Antenna Type
Built-in Directional Antenna, Horizontal 60°, Vertical 30°
Spatial Streams
2
Max Throughput
The 5GHz frequency band provides a wireless transmission speed of up to
867Mbps.
Modulation Types
OFDM: BPSK@6/9Mbps, QPSK@12/18Mbps, 16-QAM@24Mbps,
64-QAM@48/54Mbps
OFDM: BPSK, QPSK,16QAM, 64QAM, 256QAM
Receiver sensitivity
802.11a: -89 dBm (6 Mbps), -80 dBm (24 Mbps), -76 dBm (36 Mbps), -71 dBm (54
Mbps)
802.11n: -83 dBm@MCS0, -65 dBm@MCS7, -83 dBm@MCS8, -65 dBm@MCS15
802.11ac: -86 dBm(MCS0), -63 dBm(MCS9)
Max Transmit Power
400mw (26dBm) (Single-Stream)
Transmit Power
Adjustment
1 dBm
Dimensions (L x W x
H, without bracket)
147 mm ×76 mm ×37 mm (5.78 in. x 2.99 in. x 1.46 in.)
Weight
0.35 kg (0.77 lbs.)

Hardware Installation and Reference Guide 1 Product Overview
5
Service Ports
One 10/100BASE-T port, supporting 24 V non-standard PoE power supply
Management Ports
N/A
Status LED
One system LED, one Ethernet port LED, and three signal LEDs
Power Supply
Method
12 VDC and 24 V non-standard PoE power supply
Max Power
Consumption
7 W
Bluetooth 5.0
Not supported
Temperature
Operating Temperature: -30°C to 55°C (-22°F to 131°F)
Storage Temperature: -40°C to 70°C (-40°F to 158°F)
Operating Humidity: 5% to 95% RH (non-condensing)
Storage Humidity: 5% to 95% RH (non-condensing)
Installation Methods
Wall Mounting/Pole Mounting
Safety
GB 4943.1-2011
EMC Compliance
GB/T 9254-2008
Vibration
IEC61373
Radio Approvals
China Radio Transmission Equipment TypeApproval Certificate, EN300 328, EN301
893
MTBF
>400000H
Warning
●This is a Class A product. In a living environment, this product may cause radio interference in which case
the user may be required to take adequate measures. In this case, users are advised to take proper
measures against the disturbance.
1.5 Power Specification
RG-EST310 V2.0 adopts 12 VDC or 24 V/0.6 A non-standard PoE power supply.

Hardware Installation and Reference Guide 1 Product Overview
6
Figure 1-3 Non-Standard PoE Adapter
⚫RJ45 Connector for LAN: 1, 2, 3 and 6 are data cables. 4 and 5 connect the positive post. 7 and 8 connect
the negative post.
⚫RJ45 Connector for PoE: 1, 2, 3 and 6 are data cables. 4 and 5 connect the positive post. 7 and 8 connect
the negative post.
Caution
●Please do not use a switch or a PoE adapter of another model for power supply. Otherwise, the device
may be damaged.
1.6 Heat Dissipation
RG-EST310 V2 adopts a fanless design. Leave sufficient space around the device for ventilation

Hardware Installation and Reference Guide 1 Safety Precautions
7
2 Safety Precautions
2.1 Safety Precautions
Note
●To prevent device damage and physical injury, please read carefully the safety recommendations
described in this chapter.
●The following safety suggestions do not cover all possible dangers.
2.1.1 General Safety Precautions
⚫Do not expose the device to high temperature, dusts, or harmful gases. Do not install the device in an
inflammable or explosive environment. Keep the device away from EMI sources such as large radar stations,
radio stations, and substations. Do not subject the device to unstable voltage, vibration, and noises.
⚫The installation site should be far away from the sea. Keep the device at least 500 meters away from the
seaside and do not face it toward the wind from the sea.
⚫The installation site should be free from water flooding, seepage, dripping, or condensation. The installation
site shall be selected according to network planning and features of communications device, and
considerations such as climate, hydrology, geology, earthquake, electric power, and transportation.
Caution
●Please follow the correct methods described in the installation guide to install and remove the device.
2.1.2 Handling Safety
⚫Prevent the device from being frequently handled.
⚫Cut off all power supplies and unplug all power cords before you move or handle the device.
2.1.3 Electric Safety
Warning
●Improper or incorrect operations may cause a fire or electric shock and other accidents, thus causing
severe even fatal damages to human bodies and device.
●Direct or indirect contact with high voltage or mains power supply via wet objects may cause fatal dangers.
⚫Please observe local regulations and specifications when performing electric operations. Only personnel
with relevant qualifications can perform such operations.
⚫Please carefully check for any potential danger in the working area, for example, damp/wet ground or floor.
⚫Find out the location of the emergency power supply switch in the room before installation. First cut off the

Hardware Installation and Reference Guide 1 Safety Precautions
8
power supply in case of an accident.
⚫Be sure to make a careful check before you shut down the power supply.
⚫Do not place the device in a damp/wet location. Do not let any liquid enter the device.
⚫Keep the device far away from the grounding or lightning protection devices of power device.
⚫Keep the device away from high-power radio stations, radar stations, and high-frequency high-current
devices.
2.2 Installation Environment Requirements
To ensure normal operation and a prolonged useful life of the device, the installation site must meet the
following requirements.
2.2.1 Environment Requirements
⚫Install the device in a well-ventilated environment. If it is installed in a closed room, make sure there is a
good cooling system.
⚫Make sure the site is sturdy enough to support the device and its accessories.
⚫Make sure the site has enough space for installing the device and leave sufficient space around the device
for ventilation.
2.2.2 Ventilation Requirements
For proper ventilation, leave sufficient space around the device.
2.2.3 Temperature/Humidity Requirements
To ensure the normal operation and prolonged service life of the device, maintain an appropriate temperature
and humidity in the equipment room. The equipment room with too high or too low temperature and humidity for
a long period may damage the device.
⚫In an environment with high relative humidity, the insulating material may have bad insulation or even leak
electricity and sometimes the materials may suffer from mechanical performance change and metallic parts
may get rusted.
⚫In an environment with low relative humidity, the insulating strip may dry and shrink, and static electricity is
prone to occur and damage the internal circuits of the device. In an environment with high temperature, the
device is subjected to even greater harm, as its performance may degrade significantly and its useful life
may be shortened in the case of long-term exposure that expedites the aging process.
Table 2-1 Temperature and Humidity Requirements
Operating Temperature
Operating Humidity:
-30°C to 55°C (-22°F to 131°F)
5% to 95% RH (non-condensing)

Hardware Installation and Reference Guide 1 Safety Precautions
9
2.2.4 Waterproof Requirements
IP65 (Specific Direction)
2.2.5 Anti-interference Requirements
⚫Take interference prevention measures for the power supply sytem.
⚫Keep the device far away from the grounding or lightning protection devices of power device.
⚫Keep the device far away from high-power radio stations, radar stations, and high-frequency high-current
devices.
2.3 Tools
Table 2-2 Tools
Common
Tools
Phillips screwdriver, hex screwdriver, related copper and fiber cables, bolts, diagonal pliers,
cable ties
Special Tools
Anti-static glove, stripping pliers, crimping pliers, crimping pliers for the crystal head, wire
cutter, waterproof tape
Meter
Multimeter
Related
devices
PC, screen and keyboard
Note
●The installation tools are not included in the scope of delivery and should be purchased separately.

Hardware Installation and Reference Guide 1 Installing the Device
10
3 Installing the Device
Caution
●Before installing the device, make sure you have carefully read the requirements described in Chapter 2.
3.1 Installation Procedure
3.2 Preparing
Carefully plan and arrange the installation location, networking mode, power supply, and cabling before
installation. Confirm the following requirements before installation: The installation position provides sufficient
space for heat dissipation.
⚫The installation position meets the temperature and humidity requirements of the device.
⚫The power supply and required current are available in the installation position.
⚫The selected power supply modules meet the system power requirement.
⚫The network cables have been deployed in the installation position.
⚫The installation site meets all described requirements.
⚫The device meets the customers’ requirements.
3.3 Precautions
It is recommended to mount the device on a pole with a diameter ranging from 35 mm to 89 mm.

Hardware Installation and Reference Guide 1 Installing the Device
11
Otherwise, you need to prepare a hose clamp of another model. The hose clamp should be at least 2.5 mm
thick.
⚫Please make sure the installation site meets the requirement in Chapter 2.2.1.
⚫Please use the 24 V PoE power adapter (Pin 4 and 5 connect to the positive post. Pin 7 and 8 connect to the
negative post) delivered with the device or use a power adapter of the same specification.
⚫The PoE adapter supports power supply over a 100-meter network cable. Before connecting the network
cable, make sure that the power supply module is off.
⚫Make sure that the connector of the power module is fully seated.
3.4 Mounting the Device
Caution
●It is recommended to install the device where you can get the optimal coverage.
●The image shown here is for indicative purpose only. The actual product may differ.
3.4.1 Wall Mounting
Figure 3-1 Wall Mounting
Ensure the network cable is connected in advanced.
1. Secure the mounting bracket on the wall using wall anchors and screws.
2. Install the device to the mounting bracket.

Hardware Installation and Reference Guide 1 Installing the Device
12
3.4.2 Pole Mounting
Figure 3-2 Pole Mounting
1. Secure the mounting bracket to the pole by threading two clamps through the mounting bracket.
2. Install the device to the mounting bracket.
3.5 Connecting Cables
Select a cable (CAT5e or higher) according to the distance between the wireless bridge and the PSE. Plug one
end of the cable into the PoE port of the PoE adapter and plug the other end into the LAN port of the device.
Connect the LAN port of the PoE adapter to the server or camera. Plug the PoE adapter into 220 V power
socket. Or you can connect the DC port of the device to the 12 VDC adapter, and connect the LAN port of the
device to the server or camera.
Figure 3-3 Connecting Cables
Warning
●Remember to install the bottom cover for waterproof and dustproof purpose.

Hardware Installation and Reference Guide 1 Installing the Device
13
●Please do not use a switch or a PoE adapter of another model. Otherwise, the device may be damaged.
3.6 Verifying Installation
Checking the Device
⚫Verify if the external power supply matches the specification.
⚫Verify that the device has been fastened and will not move or tilt.
Checking the Power Supply
⚫Make sure all power cables are properly connected.
⚫Make sure the device is operational after power-on.

Hardware Installation Guide and Reference Verifying Operating Status
14
4 Verifying Operating Status
4.1 Setting up Configuration Environment
Power on the device via 12 VDC or 24 V/0.6 A non-standard PoE power supply. Make sure all power cables are
properly connected and meet the safety requirement.
4.2 Checking Environment before/after Power-on
1. Before power-on, check the following items:
⚫Verify that the power supply is properly connected.
⚫Verify that the input voltage matches the specification.
2. After power-on, check the following item (Recommended):
⚫Check the indicator status.

Hardware Installation Guide and Reference Monitoring and Maintenance
15
5 Monitoring and Maintenance
5.1 Monitoring
When the RG-EST310 V2 is running, you can monitor the device status by observing the indicator.
5.2 Maintenance
If a hardware error occurs, please contact Ruijie Reyee Technical support for help.

Hardware Installation Guide and Reference Appendix A Connec
ors and Media Description
6 Troubleshooting
6.1 General Troubleshooting Procedure

Hardware Installation Guide and Reference Appendix A Connectors and Media Description
17
7 Appendix A Connectors and Media Description
1000BASE-T/100BASE-TX/10BASE-T
The 1000BASE-T/100BASE-TX/10BASE-T is a 10/100/1000 Mbps auto-negotiation port that supports auto
MDI/MDIX.
Compliant with IEEE 802.3ab, 1000BASE-T requires Category 5e 100-ohm UTP or STP (STP is recommended)
with a maximum distance of 100 meters (328 feet).
1000BASE-T requires all four pairs of wires be connected for data transmission, as shown in Figure 7-1.
Figure 1-1 Figure 7-1 1000BASE-T Connection
10BASE-T uses Category 3, 4, 5 100-ohm UTP/STP and 1000BASE-T uses Category 5 100-ohm UTP/STP for
connections. Both support a maximum length of 100 meters. Figure 7-2 shows100BASE-TX/10BASE-T pin
assignments.
Figure 1-2 Figure 7-2 100BASE-TX/10BASE-T Pin Assignments
Figure 7-3 shows wiring of straight-through and crossover cables for 100BASE-TX/10BASE-T.