Rupes S135 Manual

1
S 135E - S135
Dust extractors
START-UP, OPERATING AND MAINTENANCE INSTRUCTIONS

2
SPECIFICATIONS
TYPE
S 135
S 135E
RATED SUPPLY VOLTAGE ~230 V - 50 Hz ~230 V - 50 Hz
RATED POWER INPUT 1200 W max 1200 W max
RATED CURRENT INPUT 5 A 5 A
DUST EXTRACTION INTENSITY/RATE 170 m
3
/h 170 m
3
/h
NEGATIVE PRESSURE 1500 mm/H
2
O 1500 mm/H
2
O
WEIGHT [kg] 9 kg 9 kg
OVERALL DIMENSIONS 400 x 400 x 580 mm (h) 400 x 400 x 580 mm (h)
NOISE LEVEL 72 dB (A) 72 dB (A)
FILTERING AREA 1.0 m
2
1.0 m
2
FILTER TYPE U S G C U S G C
DUST CONTAINER CAPACITY 6 kg max 6 kg max
ELECTRIC SECTION
TWO-WAY POWER SWITCH ON - OFF ON - OFF
TWO-WAY MODE SWITCH - MAN. - AUTOM.
POWER SUPPLY SOCKET - YES
MAXIMUM POWER INPUT FROM MAINS SOCKET - 1500 W max

3
INTRODUCTION
This extractor has been designed and manufactured for professional applications, and it should be used for
these purposes. The extractor is designed for the extraction of dry dust only.
WARNING!
Never allow the extractor to suck in flammable substances, explosives, solvents, welding vapours, burning
substances, fuels, lubricating oils, alcohols, paints, or thinners. The collecting of dust from surfaces subject
to grinding, or coated with paint, which has not completed its catalytic cycle yet, may result in spontaneous
ignition, thus creating a serious risk of fire and/or explosion.
At a minimum of once a year the manufacturer or authorised personnel should inspect the system. NTS Sp.
z o.o. [Ltd.] will not be held responsible for any damage, direct or indirect, due to failure to follow the
guidelines provided in these Instructions.
INTRODUCTORY NOTES, MINIMUM REQUIREMENTS REGARDING POWER SUPPLY,
RATING PLATE
The machine in question has been designed and manufactured in compliance with safety rules, and
therefore it has been permitted for use as it constitutes no hazard for its users.
However, the following aspects need to be remembered:
-the machine is earthed (only S135E) and has to be connected to a proper supply network;
-do not exceed the maximum loads specified in the Specifications table;
-the machine shall be used by properly trained personnel.
MINIMUM POWER SUPPLY REQUIREMENTS
-monophase voltage 230 V - 50 Hz; with earth conductor 1.5mm
2
(only for S135E);
-automatic overload switch 6Ka 30mA 16A has to be installed before supply circuit.
RATING PLATE
-The rating plate in the back panel of the device provides general information. If you need to find
more detailed data, read “Specifications” section.

4
PRINCIPLE OF OPERATION
CHARACTERISTICS
All the features of the device have been combined in one unit to in order to allow the execution of the
following functions at the same time:
-dust extraction;
-automatic operation of electric tool (S135E);
-access to the power supply socket without the need to use extra extension cords.
SUCTION SECTION
Consists of:
-turbine;
-dust bag (7);
-filter element for dust extraction (14);
-polyester filter for extraction of liquids (15).
ELECTRIC SECTION
Consists of:
-two-way power switch (3) ON-OFF;
-two-way mode switch (4): manual - automatic;
-socket for connecting an electric tool (S135E).
MACHINE PARTS, COMPONENTS, AND ACCESSORIES
1. Extractor head
2. Rating plate
3. Power switch - I = ON, 0 = OFF
4. Mode switch: MAN (manual)
AUT (automatic)
5. Electric socket for connecting another tool
6. Power supply cable
7. Dust bag
8. Dust bag outlet
9. Plug (cap) for dust bag
10. Container
11. Extractor outlet
12. Locking hooks
13. Wheels
14. Filter element
15. Polyester filter for extraction of liquids
16. Float
17. Grip (S135E)

5
INSTALLATION
Warning:
-The machine has to be set in a dry and well-ventilated place, where the air is changed at a
minimum of once an hour; fresh air content (without equipment supporting ventilation) -
50%.
-Temperature in the place of work: 10-35°
°°
°C, humidity: 50-90%.
-The surface, on which the machine stands, may be inclined at no more than 5-10 degrees.
CONNECTION TO POWER SUPPLY NETWORK
Before connecting the power supply cable make sure that the switch is in the OFF (0) position. Connect the
machine to a socket, which is able to withstand the machine load.
CONNECTION OF TOOLS (S135E)
Insert the plug into the socket (5) (Fig. 2); if the tool is equipped with a dust extraction system, connect it via
the suction hose with the coupling (Fig. 3 and 4).
PRELIMINARY CHECK
As soon as you connect all the elements, check if:
-The dust bag (7) is inside the container (9);
-the suction hose is securely connected.
OPERATION OF DUST EXTRACTION MACHINE
The machine may be used in manual or automatic operation mode.
MANUAL OPERATION
1. Set switch (3) in the ON position (I).
2. Set switch (4) in the ON position (MAN) (only S135E).
In this setting the machine works continuously, independent of whether the tool is working or not.
AUTOMATIC OPERATION (only S135E)
Set switch (3) in the ON position (I) and switch (4) in the automatic mode (AUT).
In this setting the extraction proceeds only while the connected tool is working . As soon as the tool is
switched of, suction will automatically stop.
MANUAL OPERATION FOR EXTRACTION OF LIQUIDS
1. Release hooks (12) fastening the machine head (1) (Fig. 5).
2. Remove filter element (14) (Fig. 7-8) and dust bag (7) (Fig. 10).
3. Insert polyester filter (15) into suction basket (Fig. 9) and fasten the hooks again.
4. Set switch (3) and switch (4) (only S135E) in manual mode (MAN).
GUIDELINES
Do not connect loads exceeding the amount permissible.
First check if all the operations have been completed according to the guidelines provided above, and then
test the working of the tools in compliance with their respective operating instructions.

6
MAINTENANCE
Warning:
Always cut off the power supply before cleaning and bag or filter element replacement operations.
MAINTENANCE (performed by user)
-check the condition of suction hoses;
-always keep the machine clean;
-put on a dust-mask and clean the filter as follows:
a. open head (1) using hooks (12) (Fig. 5-6);
b. take out filter element (14) (Fig. 7-8) and clean it with a soft brush or wash with stream of water.
Make sure that it is thoroughly clean before re-using;
c. take out worn out dust bag (7) and close it with the plug (lid) (9) (Fig. 12);
d. insert a new dust bag and place it so that its hole coincides with the outlet (8), according to the
illustration (Fig. 11);
e. put back the filter element;
f. fasten the hooks of extractor head (1) and make sure that it is properly closed.
Warning:
-If dust escapes from the machine, immediately switch it off.
-In case of fire use the appropriate extinguishing media and leave your workplace.
-In case of a power failure set all switches in the OFF position to prevent spontaneous
switching on of the unit when power comes back on (S135E).
Warning:
-Use RUPES 001.1606/C dust bags only.
-Always carefully check the dust bags. If dust gets inside the unit, it may cause serious
damage.

7
POSSIBLE ABNORMALITIES AND HOW TO ELIMINATE THEM
EFFECTS
REASONS
REMEDY
It is not possible to start up the dust
extractor Power failure
Power supply cable, switch or motor
have defects
Check if the plug is in the socket
Contact an authorised service centre
Dust extractor does not start
automatically (S135E) Failure of electronic module or microswitch Contact an authorised service centre
Impaired dust extraction intensity/rate Overfilled dust container (S135E)
Dusts escape from the outlet line
Check the filtering container
Check the flexible tube and
accessories
Escaping of dust from the outlet line Damaged filter Contact an authorised service centre
It is not possible to activate the tools
(S135E) Automatic switching mechanism failure
Contact an authorised service centre
DECLARATION OF CONFORMITY
CE mark awarded in 1996
We hereby declare assuming full responsibility that the presented dust/liquid extractor for industrial applications
conforms with directives concerning basic safety requirements:
73/23/CEE - Low Voltage + 93/68/CEE
89/336/CEE - Electromagnetic Compatibility + 91/263/CEE + 92/31/CEE + 93/68/CEE
The tests were performed according to European Regulations.
Low Voltage: EN 60335-1, EN 60335-2-2/A2;
Electromagnetic Compatibility: EN 55014-1, EN 61000-3-2;
Tests and limits concerning emitted noise: EN 23374.

8
RUPES DUST EXTRACTOR
WIRING DIAGRAM FOR S135E
WIRING DIAGRAM FOR S135

9
WARRANTY TERMS AND CONDITIONS
1. NTS Sp. z o.o. [Ltd.] - the exclusive representative of RUPES s.p.a. in the Republic of Poland
guarantees the highest quality and correct working of the machine operated in compliance with its
operating instructions.
2. The Buyer obtains a 12-month warranty starting from the date the machine was purchased . This
period will be extended by the number of days the machine is kept in the warranty repair service.
3. Machine defects revealed during the warranty period will be removed as soon as possible, however
within no more than 14 days. The repair period starts from the day the damaged machine is
delivered to the warranty repair centre.
4. The warranty does not cover the following:
a) random damage due to the machine work with the electrical system or compressed air
supply system,
b) mechanical damage caused by operation inconsistent with the enclosed operating
instructions,
c) any damage caused by operation inconsistent with the enclosed operating instructions,
d) damage being the consequence of repairs carried out in any place other than warranty
repair centre,
e) operation actions specified in the operating instructions,
f) disposable elements of the unit: carbon brushes, rubber elements, fuses, etc.
MACHINE RATING PLATE
LAY-OUT AND DEFINITIONS
1. Machine type.
2. Rated voltage in volts (V).
3. Frequency in hertz (Hz).
4. Machine identification number or serial number.
5. Power input in watts (W).
6. Dust extraction intensity/rate.

10
Poland, 05-083 Zaborów
Borzęcin DuŜy
ul. Warszawska 749
tel.: [phone]
fax: [phone]
e-mail: [e-mail]
http://www.nts.com.pl