Ryobi P4001 User manual

OPERATOR’S MANUAL
MANUEL D’UTILISATION
MANUAL DEL OPERADOR
18 VOLT DRAIN AUGER
DÉGORGEOIR POUR TUYAUTERIE
DE 18 V
BARRENA DE DRENAJE DE 18 V
P4001
WARNING: To reduce the
risk of injury, the user must read and
understand the operator’s manual
before using this product.
SAVE THIS MANUAL FOR
FUTURE REFERENCE
ADVERTENCIA: Para reducir
elriesgodelesiones,elusuariodebeleer
y comprender el manual del operador
antes de usar este producto.
AVERTISSEMENT : Pour
réduire les risques de blessures,
l’utilisateur doit lire et veiller à bien
comprendrele manuel d’utilisation avant
d’employer ce produit.
GUARDE ESTE MANUAL
PARA FUTURAS CONSULTAS
CONSERVER CE MANUEL
POUR FUTURE RÉFÉRENCE
TABLE OF CONTENTS
****************
General Power Tool
Safety Warnings..............................2-3
Drain Auger Safety Warnings ..........3-4
Symbols..............................................5
Features..............................................6
Assembly............................................6
Operation.........................................6-8
Maintenance.......................................8
Illustrations ....................................9-10
Parts Ordering
and Service .........................Back page
TABLE DES MATIÈRES
****************
Avertissements de sécurité générales
relatives aux outils électriques........2-3
Avertissements de sécurité relatifs
dégorgeoir pour tuyauterie .............3-4
Symboles............................................5
Caractéristiques .................................6
Assemblage........................................6
Utilisation ........................................6-8
Entretien .............................................8
Illustrations ....................................9-10
Commande de pièces
et dépannage................... Page arrière
ÍNDICE DE CONTENIDO
****************
Advertencias de seguridad para
herramientas eléctrica ................... 2-3
Advertencias de seguridad de
barrena de drenaje ........................ 3-4
Símbolos............................................5
Características ...................................6
Armado..............................................6
Funcionamiento............................. 6-8
Mantenimiento...................................8
Illustraciones................................ 9-10
Pedidos de piezas
y servicio.......................Pág. posterior

2 — English
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
WORK AREA SAFETY
  Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
 Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
 Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded surfaces
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body
is earthed or grounded.
Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of a GFCI reduces the
risk of electric shock.
Use this product only with batteries and chargers listed
in tool/appliance/battery pack/charger correlation
supplement 987000-432.
PERSONAL SAFETY
Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
power tool in unexpected situations.
POWER TOOL USE AND CARE
Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.

3 — English
GENERAL POWER TOOL SAFETY WARNINGS
DRAIN AUGER SAFETY WARNINGS
Always wear safety goggles or eye protection with
side shields marked to comply with ANSI Z87.1 when
assembling parts, operating the tool, or performing
maintenance. Following this rule will reduce the risk of
serious personal injury.
Position the the drain auger within four inches of the
drain or inlet being cleared. Operating the tool at greater
distances can result in the cable twisting or binding.
Avoid running the tool in reverse for extended periods
of time as this can damage the cable.
Never place your hand near the drum or the cable as
it is rotating. Following this rule will reduce the risk of
serious personal injury.
Clogged drains may contain bacteria, cleaning
solutions, or other potentially harmful substances.
Always wear protective clothing, eye protection,
and gloves while operating this tool to prevent these
substances from contacting your skin and eyes.
When removing the cable from a drain, remove it
slowly to avoid “splash back”. Use warm, soapy water
to clean hands and other body parts that may have been
exposed to potentially harmful substances.
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
when not using your battery tool or when changing
accessories. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
Do not place battery tools or their batteries near fire
or heat. This will reduce the risk of explosion and possibly
injury.
Do not crush, drop or damage battery pack. Do not
use a battery pack or charger that has been dropped
or received a sharp blow. A damaged battery is subject
to explosion. Properly dispose of a dropped or damaged
battery immediately.
Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
BATTERY TOOL USE AND CARE
Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack.
Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury and fire.
When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys, nails,
screws, or other small metal objects, that can make
a connection from one terminal to another. Shorting
the battery terminals together may cause burns or a fire.
Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
SERVICE
Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
When servicing a power tool, use only identical
replacement parts. Follow instructions in the
Maintenance section of this manual. Use of unauthorized
parts or failure to follow Maintenance instructions may
create a risk of shock or injury.

4 — English
DRAIN AUGER SAFETY WARNINGS
Batteries can explode in the presence of a source
of ignition, such as a pilot light. To reduce the risk of
serious personal injury, never use any cordless product
in the presence of open flame. An exploded battery can
propel debris and chemicals. If exposed, flush with water
immediately.
Do not charge battery tool in a damp or wet location.
Do not use, store, or charge battery packs or products
in locations where the temperature is less than 50°F
or more than 100°F. Do not store outside or in vehicles.
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in contact
with your skin, wash immediately with soap and water.
If liquid gets into your eyes, flush them with clean
water for at least 10 minutes, then seek immediate
medical attention. Following this rule will reduce the risk
of serious personal injury.
Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If you
loan someone this tool, loan them these instructions also.

5 — English
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
DANGER: Indicates a hazardous situation, which, if not avoided, will result in death or
serious injury.
WARNING: Indicates a hazardous situation, which, if not avoided, could result in death or
serious injury.
CAUTION: Indicates a hazardous situation, that, if not avoided, may result in minor or
moderate injury.
NOTICE:(Without Safety Alert Symbol) Indicates information considered important, but
not related to a potential injury (e.g. messages relating to property damage).
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
Safety Alert Indicates a potential personal injury hazard.
Read Operator’s
Manual
To reduce the risk of injury, user must read and understand operator’s manual
before using this product.
Eye Protection Always wear safety goggles or eye protection with side shields marked to
comply with ANSI Z87.1.
Wet Conditions
Alert Do not expose to rain or use in damp locations.
Wear Gloves Wear non-slip, heavy-duty protective gloves when handling the drain auger.
Long Hair Risk of long hair being drawn into rotating drum.
Loose Clothing Risk of loose clothing being drawn into rotating drum.
Recycle Symbols
This product uses lithium-ion (Li-ion) batteries. Local, state or federal laws
may prohibit disposal of batteries in ordinary trash. Consult your local waste
authorityfor information regardingavailable recyclingand/ordisposal options.
V Volts Voltage
min Minutes Time
Direct Current Type or a characteristic of current
n
o
No Load Speed Rotational speed, at no load
.../min Per Minute Revolutions, strokes, surface speed, orbits etc., per minute

6 — English
FEATURES
PRODUCT SPECIFICATIONS
Cable Diameter........................................................ 0.25 in.
Cable Length...............................................................25 ft.
Minimum pipe size (diameter) ................................. 0.75 in.
Maximum pipe size (diameter) ..................................... 2 in.
WARNING:
Do not attempt to modify this product or create
accessories or attachments not recommended for use
with this product. Any such alteration or modification is
misuse and could result in a hazardous condition leading
to possible serious personal injury.
WARNING:
Do not use this product if it is not completely assembled
or if any parts appear to be missing or damaged. Use of
a product that is not properly and completely assembled
or with damaged or missing parts could result in serious
personal injury.
ASSEMBLY
OPERATION
If any parts are damaged or missing, please call 1-800-525-2579 for assistance.
WARNING:
Do not allow familiarity with this product to make you
careless. Remember that a careless fraction of a second
is sufficient to inflict serious injury.
WARNING:
Always remove battery pack from the tool when you are
assembling parts, making adjustments, cleaning, or when
not in use. Removing battery pack will prevent accidental
starting that could cause serious personal injury.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes and other possible
serious injuries.
WARNING:
Do not use any attachments or accessories not
recommended by the manufacturer of this product. The
use of attachments or accessories not recommended
can result in serious personal injury.
APPLICATIONS
You may use this product for the purposes listed below:
Clearing obstructions from sinks, toilets, and bathtubs.
INSTALLING/REMOVING BATTERY PACK
See Figure 1, page 9.
Lock the switch trigger.
Insert the battery pack into the product as shown.
Make sure the latches on each side of the battery pack
snap in place and that battery pack is secured in the
product before beginning operation.
Depress the latches to remove the battery pack.
For complete charging instructions, see the operator’s
manuals for your battery pack and charger.
VARIABLE SPEED SWITCH TRIGGER
See Figure 2, page 9.
The variable speed switch trigger delivers higher speed with
increased trigger pressure and lower speed with decreased
trigger pressure.
To turn the tool ON, depress the switch trigger. To turn it
OFF, release the switch trigger and allow the cable to come
to a complete stop.

7 — English
NOTICE:
Do not advance or retract the cable using the switch
trigger unless the cable is in a drain pipe.
To advance the cable using the switch trigger:
Squeeze the pommel and, if desired, engage the auto-
feed lock.
 Place the direction of rotation selector in the forward
position.
 Squeeze and hold the switch trigger to advance the cable.
NOTE: Once the cable has been advanced to your desired
length, it can be locked in place with the cable lock lever.
Move the lever down to engage the clamp and up to
disengage.
NOTICE:
Do not attempt to advance or retract the cable using the
switch trigger with the clamp engaged.
To retract the cable, place the direction of rotation
selector in the reverse position, squeeze the pommel,
and depress the switch trigger.
NOTICE:
Do not run the drain auger in forward or reverse for
extended periods of time. Failure to follow these
instructions can result in damage to the tool.
USING THE DRAIN AUGER
See Figures 6 and 7, page 10.
The drain auger can be used to clear obstructions from a
variety of drains including sink, bathtub, and toilet drains.
NOTE: This product can be used to clear drain pipes with
minimumdiametersof 0.75in. andmaximumdiameters of2in.
To clear obstructions:
Remove the cap from the end of the cable.
When removing an obstruction from a sink or a bathtub,
it may be neccesary to remove the stopper or overflow
cover to gain access to the drain pipe. Toilet drains can
be accessed directly through the base of the bowl.
Hold the drain auger within four inches of the drain or
overflow, and manually feed the cable into the drain pipe.
NOTE: Advance the cable slowly at first. Advancing it too
rapidly can result in twisting or binding.
After feeding about six inches of cable into the drain, you
may begin advancing the cable using the switch trigger
or continue advancing it manually.
OPERATION
DIRECTION OF ROTATION SELECTOR
(FORWARD/REVERSE/CENTER LOCK)
See Figure 2, page 9.
Set the direction of rotation selector in the OFF (center lock)
positionto lock theswitch trigger andhelp preventaccidental
starting when not in use.
Position the direction of rotation selector to the left of the
switch trigger for forward operation. Position the selector to
the right of the switch trigger to reverse the direction.
NOTE: The tool will not run unless the direction of rotation
selector is pushed fully to the left or right.
NOTICE:
To prevent gear damage, always allow the cable to come to
a complete stop before changing the direction of rotation.
WARNING:
Battery tools are always in operating condition. Lock
the switch when not in use or carrying at your side,
when installing or removing the battery pack, and when
manually advancing or retracting the cable.
AUTO-FEED LOCK
See Figure 3, page 9.
The auto-feed lock feature allows the user to advance the
cable using the switch trigger without holding the pommel.
To engage, squeeze the pommel and push the auto-feed
lock button to the left.
To release, squeeze the pommel and push the auto-feed
lock button to the right.
ADVANCING/RETRACTING THE CABLE
See Figures 4 and 5, page 10.
To manually advance the cable:
Lock the switch trigger by placing the direction of rotation
selector in center position.
Hold the front handle with one hand and advance the
cable with the other.
NOTE: Once the cable has been advanced to your desired
length, it can be locked in place with the cable lock lever.
Move the lever down to engage the clamp and up to
disengage.
To retract the cable, hold the front handle with one hand
and pull the cable back with the other.

8 — English
OPERATION
The cable should advance freely through the drain pipe
until it contacts the obstruction or is caught in a P-trap.
If the cable is caught in a P-trap, additional force or
increased trigger pressure should be enough to advance
it past the bend in the pipe.
If the cable has contacted an obstruction, there are two
ways to remove it:
• Advance the cable by squeezing the switch trigger.
Hold the trigger for several seconds allowing the tip
of the cable to bore into the obstruction. If the cable
stops rotating, release the switch trigger to avoid
kinking or damaging the cable. Clamp the cable
in place, then push or pull until the obstruction is
dislodged. Unclamp the cable and slowly retract it
from the drain pipe.
• Release the pommel and, if neccesary, disengage
the auto-feed lock. Squeeze the switch trigger. The
cable will rotate, but it will not advance. Hold the
trigger for several seconds allowing the obstruction
to wrap around the cable. If the cable stops
rotating, release the switch trigger to avoid
kinking or damaging the cable. Then slowly retract
the cable and pull the obstruction through the drain.
NOTE: When removing the cable from a drain, remove it
slowly to avoid “splash back”.
Once the obstruction is cleared, attempt to flush your
toilet or run water through your drain to confirm that the
water is flowing freely.
After the cable has been properly cleaned, as described
in the next section, place the cap on the end of the cable.
CLEANING THE DRAIN AUGER
See Figures 8 and 9, page 10.
The drain auger should be cleaned after each use to prevent
contamination and residue build up.
To drain the drum:
Remove the battery pack from the tool.
Hold the tool at an angle and lift the drain tab located on
the back of the tool.
Allow any liquids inside the drum to pour down a drain
or into a container approved for liquid waste.
To clean the cable:
Remove the battery pack from the tool.
Using a clean cloth and warm soapy water, pull the cable
out from the tool, cleaning it as it advances.Continue
until the cable has been fully advanced and completely
cleaned.
Using a clean, dry cloth, pull the cable back into the tool,
drying it as it retracts. Continue until the cable has been
fully retracted.
To ensure that no water entered the tool, drain the drum
as described earlier.
Place the cap on the end of the cable.
NOTICE:
Do not advance or retract the cable using the switch
trigger unless the cable is in a drain pipe.
MAINTENANCE
NOTE: ILLUSTRATIONS START ON PAGE 9 AFTER FRENCH
AND SPANISH LANGUAGE SECTIONS.
WARNING:
When servicing, use only identical replacement parts.
Use of any other parts could create a hazard or cause
product damage.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.

NOTES/NOTAS

2 — Français
AVERTISSEMENT
Lire tous les avertissements et toutes les instructions.
Ne pas suivre l’ensemble des avertissements et des
instructions peut entraîner une électrocution, un incendie
ou des blessures graves.
Conserver les avertissements et les instructions à des
fins de référence ultérieure. Le terme « outil motorisé »,
utilisé dans tous les avertissements ci-dessous désigne tout
outil fonctionnant sur secteur (câblé) ou sur piles (sans fil).
SÉCURITÉ DU LIEU DE TRAVAIL
  Garder le lieu de travail propre et bien éclairé. Les
endroits encombrés ou sombre s sont propices aux
accidents.

  Ne pas utiliser d’outils électriques dans des
atmosphères explosives, par exemple en présence
deliquides, gaz ou poussièresinflammables. Les
outils électriques produisent des étincelles risquant
d’enflammer les poussières ou vapeurs.

  Garderles enfants etbadaudsà l’écart pendant
l’utilisationd’un outil électrique.Les distractions
peuvent causer une perte de contrôle.
SÉCURITÉ ÉLECTRIQUE
Lesfichesdesoutilsélectriquesdoiventcorrespondre
à la prise secteur utilisée. Ne jamais modifier la fiche,
dequelque façon quece soit. Nejamais utiliser
d’adaptateursdeficheavecdesoutilsmisàlaterre.
Les fiches et prises non modifiées réduisent le risque de
choc électrique.
Éviter tout contact du corps avec des surfaces mises
àlaterre,tellesquetuyaux,radiateurs,cuisinièreset
réfrigérateurs.Le risque de choc électrique est accru
lorsque le corps est mis à la terre.

Nepas exposer les outilsélectriques à l’eau ou
l’humidité.La pénétration d’eau dans ces outils accroît
le risque de choc électrique.

Nepasmaltraiterlecordond’alimentation.Nejamais
utiliserle cordon d’alimentationpour transporter
l’outiletnejamaisdébranchercedernierentirantsur
lecordon.Garderlecordonàl’écartdelachaleur,
del’huile, des objetstranchants et des piècesen
mouvement. Un cordon endommagé ou emmêlé accroît
le risque de choc électrique.

Pourles travaux àl’extérieur, utiliserun cordon
spécialementconçu à ceteffet.Utiliser un cordon
conçu pour l’usage extrérieur pour réduire les risques de
choc électrique.

S’ilestnécessaired’utiliserl’outilélectriquedansun
endroithumide,employerundispositifinterrupteurde
défaut à la terre (GFCI). L’utilisation d’un GFCI réduit le
risque de décharge électrique.

Utiliserceproduitseulementaveclapilesetlechargeurs
indiquésdans lesupplément deraccordement pour
chargeur/outils/piles/appareiln˚987000-432.
SÉCURITÉ PERSONNELLE
Rester attentif, prêter attention au travail et faire
preuvede bon senslors de l’utilisationde tout
outilélectrique.Ne pasutiliser cetoutil enétatde
fatigueou sous l’influencede l’alcool,de drogues
ou de médicaments. Un moment d’inattention pendant
l’utilisation d’un outil électrique peut entraîner des
blessures graves.

Utiliserl’équipementdesécurité.Toujoursporterune
protection oculaire. L’équipement de sécurité, tel qu’un
masque filtrant, de chaussures de sécurité, d’un casque
ou d’une protection auditive, utilisé dans des conditions
appropriées réduira le risque de blessures.

Éviterles démarrages accidentels. S’assurer que
lecommutateur est en positiond’arrêt avant de
brancherl’outil. Porter un outil avec le doigt sur son
commutateur ou brancher un outil dont le commutateur
est en position de marche peut causer un accident.

Retirerlesclésderéglageavantdemettrel’outilen
marche. Une clé laissée sur une pièce rotative de l’outil
peut causer des blessures.
Ne pas travailler hors de portée. Toujours se tenir
biencampéetenéquilibre.Ceci permettra de mieux
contrôler l’outil en cas de situation imprévue.
Porter une tenue appropriée. Ne porter ni vêtements
amples, ni bijoux. Garder les cheveux, les vêtements
etlesgantsàl’écartdespiècesenmouvement.Les
vêtements amples, bijoux et cheveux longs peuvent se
prendre dans les pièces en mouvement.

Si les outils sont équipés de dispositifs de
dépoussiérage,s’assurer qu’ils sont connectés et
correctement utilisés. L’usage de ces dispositifs de
dépoussiérage peut réduire les dangers présentés par
la poussière.

Nepasutiliserl’outilsuruneéchelleouunsupport
instable. Une bonne tenue et un bon équilibre permettent
de mieux contrôler l’outil en cas de situation imprévue.
UTILISATION ET ENTRETIEN DES OUTILS
ÉLECTRIQUES
Nepas forcer l’outil. Utiliser l’outilappropriépour
l’application.Un outil approprié exécutera le travail
mieux et de façon moins dangereuse s’il est utilisé dans
les limites prévues.
AVERTISSEMENTS DE SÉCURITÉ GÉNÉRALES RELATIVES
AUX OUTILS ÉLECTRIQUES