Safco 7752 User manual

MODEL
NUMBER 7752
7752-37: 1 of 2; Rev. 1: 12/01
Riser for Sorter Module
For questions or concerns, please call
Safco Consumer Hot Line 1-800-664-0042
available Monday-Friday 8:00 AM to 4:30 PM (Central Time)
(English-speaking operators)
ASSEMBLY INSTRUCTIONS
Safco Products Company, New Hope, MN 55428
Back Panel 1 7752-01
Right Side Panel 1 7752-04
Left Side Panel 1 7752-03
Interior Left Side Panel 1 7752-02
Interior Right Side Panel 1 7752-06
Top Panel 1 7752-05
Gaskets 2 7752-15
Q
Q
Q
Q
Q
Q
Q
LETTER
CODE DESCRIPTION QTY. PART NO.
PARTS LIST
Sort and count your parts!
A
B
C
D
E
F
G
This product will assemble very easily IF you read and follow the instructions carefully.
So take your time, read your instructions, and enjoy your project.
IMPORTANT READ and FOLLOW these instructions carefully!
CHECK ALL PACKAGING - there may be parts in it!
SORT and COUNT your parts - compare with the list below. If you find problems,
refer to the Product Warranty Registration form included with this product.
2
Insert G Gaskets into the two cutouts on the bottom
edge of the A Back Panel, if not already installed.
3
1
ASSEMBLED UNIT
QQ
QQ
Q
B
QQ
QQ
Q
F
QQ
QQ
Q
G
QQ
QQ
Q
CQQ
QQ
Q
D
QQ
QQ
Q
A
QQ
QQ
Q
QQ
QQ
Q
QQ
QQ
Q
A
QQ
QQ
Q
G
CUTOUTS
Z41756A2 06-20-133
QQ
QQ
Q
E

7752-37: 2 of 2; Rev. 1: 12/01 Safco Products Company, New Hope, MN 55428
From the left side, position the C Left Side Panel
with the tabs to the back and the flange side facing to
the right. Insert the tabs on the left side panel into
the tab slots on the Back Panel from the BACK side
(see Inset B).
5
With the B Right Side Panel extended out at approximately 45
degrees, insert one E Interior Right Side Panel (with tabs UP and
recessed side facing the side panel) behind the turned-in flanges on
the front and lower sides of the right side panel. Gently swing the
front of the side panel assembly in to form a 90 degree angle. Repeat
for the C Left Side Panel using the D Interior Left Side Panel.
6
Attach the F Top Panel (with the recessed side facing down) onto
the back and side panels, making sure the back flange on the top
panel slides in BETWEEN the back panel and the two inner rails
(Inset C).
7
Position A Back Panel with the inner rails facing
you. Place the B Right Side Panel with the tabs to
the back and the flange side facing to the left. Insert
the tabs on the Right Side Panel into the tab slots on
the Back Panel from the BACK side (see Inset A).
4
INNER RAIL
QQ
QQ
Q
TAB &
TAB SLOT
BACK PANEL
QQ
QQ
QQQ
QQ
Q
QQ
QQ
Q
B
INNER RAIL
TAB &
TAB SLOT
Inset A
QQ
QQ
Q
C
Inset B
TURNED-IN FLANGE
QQ
QQ
Q
E
INNER RAILS
QQ
QQ
Q
QQ
QQ
Q
Inset C
BACK PANEL
BACK PANEL QQ
QQ
Q
B
QQ
QQ
Q
F
The flanges on the Top Panel must be
on the INNER side of the back
and side panels.
HINT: Do NOT
pre-assemble the
interior panels to
the side panels.
HINT: Do NOT try to slide the interior
panels into the side panels without
angling the side panels outward.
INNER RAILS
FLANGE
NOTE: Firmly
grasp the sides
with a helper and
carefully lift the
assembled Riser
into place.
QQ
QQ
Q
C
QQ
QQ
Q
D
QQ
QQ
Q
QQ
QQ
QQQ
QQ
Q
SLOTS TO THE BACK