Safco Main station base 7756 User manual

MODEL
NUMBER 7756
7756-37: 1 of 2; 05/00
Mail Station Base
ASSEMBLY INSTRUCTIONS
Back Panel 1 7756-01
Left Panel 1 7756-02
Right Panel 1 7756-03
Top Panel 1 7756-04
Front Rail 1 7756-05
Back Leg 2 7756-06
Front Leg (Bent 2 7756-07
Glide Adaptor 4 7749-26
Adjustable Glide 4 7749-25
Leg Adjustment Bolt 4 7756-22
Machine Screw 8 7749-28
Hex Nut 8 7749-29
o
o
o
o
o
o
o
o
o
o
o
o
LETTER
CODE DESCRIPTION QTY. PART NO.
PARTS LIST
Sort and count your parts!
A
B
C
D
E
F
G
H
I
J
K
L
IMPORTANT tREAD and FOLLOW these instructions carefully!
tCHECK ALL PACKAGI G - there may be parts in it!
tSORT and COU T your parts - compare with the list below. If you find problems,
refer to the Product Warranty Registration form included with this product.
TOOLS REQUIRED:
#2 Phillips Screwdriver, Adjust ble Wrench
ASSEMBLED U IT
o
I
o
H
o
K
o
D
o
G
o
F
o
Jo
E
o
A
o
L
o
C
o
B
Z41790A0

7756-37: 2 of 2; 05/00
Locate B Left and C Right Panels
as illustrated. Work with one side
at a time to align the holes on the
A Back Panel with the holes on the
back end of each end Panel. From
the back side, insert two
K Machine Screws into the holes,
fastening with one L Hex ut per
screw.
1o
LEFT PA EL
RIGHT PA EL
o
o
o
o
Set the unit upright onto its legs. Check to insure
the unit is at the desired height. If not, carefully turn
the unit over and adjust the legs and leg screws.
Once the base is in place and at the desired height,
level it by turning the adjustable glides on each leg.
A level is recommended for accuracy.
5
Turn glid l ft to
rais th l g;
turn glid right
to low r th l g.
GLIDE
NOTE:
If assembled unit is extremely uneven, make sure you
have used the same leg and leg sleeve hole positions
on all legs. If not, turn the unit over and adjust the legs.
4Place the unit onto its back on a protected surface.
Gently tap the H Glide Adaptors into each leg at the
end opposite the set of adjustment holes. Thread the
I Adjustable Glides all the way into each glide adaptor.
Insert the straight F Back Legs into the sleeves at the
back of the unit, and the angled G Front Legs into
the sleeves at the front. Securely fasten all legs at the
SAME HEIGHT LEVEL with one J Leg Adjustment Bolt
per leg.
o
o
o
o
o
Attach E Front Rail by aligning the
two holes on each side of the front
rail with two holes on the upper,
front of each end panel. From the
front, insert four K Machine Screws
into these holes, fasten with four
L Hex uts.
2o
FRO T
BACK PA EL
o
o
Insert the D Top Panel (with the
raised circles on top) onto the back
and side panels, making sure the
flanges on the top panel slide in
BETWEE the panels and the
inner rails.
3o
I ER RAILS
GLIDE ADAPTOR
LEG
ADJUSTABLE GLIDE
LEG
SLEEVE
BACK PA EL
o
D
o
E
o
L
o
K
o
L
o
K