Safe Fleet Prime Design VBB TC21B User manual

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: [phone] ▪Toll Free: 1.8.PRIME.RACK ▪Fax: [phone] ▪Email: i[email protected] ▪Website: www.primedesign.net
TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING
2
2
1
3
Channels (2X)
Foam Pad (10X)
Mounting Plate (10X)
M6 Locknut (10X) End Caps (4X) Brackets (4X)
M6 x 30MM Bolt (10X)
M6 Sealing Washer (10X) ” Washer (10X)” Flat Washer (10X)
VBB-TC21B ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS
1—FBM-0007 ........................................................ (Qty 1)
Channels with hardware
CONTENTS OVERVIEW
2—Crossbar Assembly........................................... (Qty 2)
3—Ladder Stop Assembly ..................................... (Qty 4)
1.75”

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: [phone] ▪Toll Free: 1.8.PRIME.RACK ▪Fax: [phone] ▪Email: in[email protected] ▪Website: www.primedesign.net
TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING
3
Rear
Front
Left
Right
2.00”
Channel Front
6.25”
Channel Rear
2
1
3
VBB-TC21B ASSEMBLY INSTRUCTIONS–FBM MOUNTINGS
FBM-0007
BASE ASSEMBLY
1.1
Foam pad
Mounting Plate
1.2 Install the fasteners through the innermost factory roof
holes as shown then torque the nuts to 60 in-lbs.
Do not install or fasten Hardware to the outer front
and rear roof holes until Step 1.4.
Install three sets of Channel Hardware per channel
as shown below.

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: [phone] ▪Toll Free: 1.8.PRIME.RACK ▪Fax: [phone] ▪Email: in[email protected] ▪Website: www.primedesign.net
TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING
4
Rear
Front
Left
Right
72.00”
7.00”
Channel Rear Channel Front
VBB-TC21B ASSEMBLY INSTRUCTIONS–FBM MOUNTINGS
1.3
1.5 Set to distances then torque all the Mounting Brackets
to 90 in-lbs.
1.4 Install the remaining front and rear fasteners through
the factory roof holes as shown then torque the nuts
to 60 in-lbs.
Install the Mounting Brackets along with the remaining
Channel Hardware as shown below.
Do not tighten the Mounting Brackets until Step 1.5.
Loosen bolts

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: [phone] ▪Toll Free: 1.8.PRIME.RACK ▪Fax: [phone] ▪Email: in[email protected] ▪Website: www.primedesign.net
TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING
5
Rear
Front
Even EvenFront
Even EvenRear
CROSSBARS CROSSBAR ADJUSTMENT
2.1
Torque to
90 in-lbs 2.2
VBB-TC21B ASSEMBLY INSTRUCTIONS–BASE ASSEMBLY
LADDER STOPS
3.2
Torque to 90 in-lbs
3.1
Loosen nuts

Page Intentionally Left Blank

Page Intentionally Left Blank

USAM-VBBTC21B-US01 Rev-C 0718