Safe Fleet PRIME DESIGN VBB C11B User manual

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: [phone] ▪Toll Free: 1.8.PRIME.RACK ▪Fax: [phone] ▪Email: i[email protected] ▪Website: www.primedesign.net
TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING
2
2
1
3
Channels (2X)
M6 Locknut (8X) End Caps (4X) Brackets (4X)
M6 x 30MM Bolt (8X)
M6 Sealing Washer (8X) Foam Pad (8X)
Mounting Plate (8X)
” Washer (8X)” Flat Washer (8X)
VBB-TC11B ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS
1—FBM-0006 ........................................................ (Qty 1)
Channels with hardware
CONTENTS OVERVIEW
2—Crossbar Assembly........................................... (Qty 2)
3—Ladder Stop Assembly ..................................... (Qty 4)
1.75”

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: [phone] ▪Toll Free: 1.8.PRIME.RACK ▪Fax: [phone] ▪Email: in[email protected] ▪Website: www.primedesign.net
TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING
3
5.00”
Channel Front
6.25”
Channel Rear
Bracket Nut
Fig. 1
Rear
Front
Left
Right
Front Mounting Brackets
21
3
VBB-TC11B ASSEMBLY INSTRUCTIONS–FBM MOUNTINGS
FBM-0006
CHANNELS TO ROOF 1.2
Front Mounting Brackets only: remove and save
the hardware from the rear Bracket Nut as shown.
1.1
Slide the Bracket Nuts into the Channels as shown.
ASSEMBLY SEQUENCE

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: [phone] ▪Toll Free: 1.8.PRIME.RACK ▪Fax: [phone] ▪Email: in[email protected] ▪Website: www.primedesign.net
TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING
4
Rear
Front
Left
Right
VBB-TC11B ASSEMBLY INSTRUCTIONS–FBM MOUNTINGS
1.6 Reinstall the Mounting Bracket Nut hardware as shown,
but do not tighten.
Install the front Mounting Brackets as shown and slide
into position over the Bracket Nut.
1.5
Loosen bolts
1.4
1.3
Foam pad
Mounting Plate
Install three sets of Channel Hardware per channel
as shown below.
Install the fasteners through the innermost factory roof
holes as shown then torque the nuts to 60 in-lbs.
Do not install or fasten Hardware to the outer front
and rear roof holes until Step 1.9.

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: [phone] ▪Toll Free: 1.8.PRIME.RACK ▪Fax: [phone] ▪Email: in[email protected] ▪Website: www.primedesign.net
TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING
5
60.00”7.00”
Channel Rear Channel Front
Rear
Front
Left
Right
VBB-TC11B ASSEMBLY INSTRUCTIONS–FBM MOUNTINGS
1.9
1.8
Set to distances then torque all the Mounting Brackets
to 90 in-lbs.
Install the remaining rear fasteners through the
factory roof holes then torque the nuts to 60 in-lbs.
1.7
Loosen bolts
Install the rear Mounting Brackets along with the
remaining Channel Hardware as shown below.
Do not tighten the Mounting Brackets until Step 1.9.

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: [phone] ▪Toll Free: 1.8.PRIME.RACK ▪Fax: [phone] ▪Email: in[email protected] ▪Website: www.primedesign.net
TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING
6
Rear
Front
Even EvenFront
Even EvenRear
CROSSBARS CROSSBAR ADJUSTMENT
2.1
Torque to
90 in-lbs 2.2
VBB-TC11B ASSEMBLY INSTRUCTIONS–BASE ASSEMBLY
LADDER STOPS
3.2
Torque to 90 in-lbs
3.1
Loosen nuts

Page Intentionally Left Blank

USAM-VBBTC11B-US01 Rev-C 0718