Safety Technology International STI-SA5000 SERIES User manual

Select-Alert Alarm
Mini Controller
We protect the things that protect you.®
Features
· Use as a cabinet alarm, door alarm,
link with push button/switch or as a
burglar alarm.
· Independent strobe and siren timing
of 15 seconds, 30 seconds, 60
seconds or continuous.
· Durable, polycarbonate construction.
· Includes ten high intensity LED’s.
· Siren offers 32 user selectable tones.
· Choose piercing 100 or 85 dB alarm.
· For indoor use only.
· Available with amber, green, blue,
red or white lens.
· Includes a tamper switch which
triggers the alarm when unit is
being removed from a wall.
· Low battery indicator.
· Powered by a 9 VDC battery
(not included) or external 12 – 24
volts.
· One Form “C” dry relay contact
output.
STI-SA5000 SERIES

- 2 -
CONTENTS
Warnings and Cautions .............................................................................................page 3
Warranty Information.................................................................................................page 3
Dimensions ..............................................................................................................page 3
Specifications ...........................................................................................................page 4
Electronic Setup........................................................................................................page 4
Alarm Tones .............................................................................................................page 5
Alarm Timing and Volume..........................................................................................page 5
Terminal Strip Connections ........................................................................................page 6
Mounting Options......................................................................................................page 6
Electronics................................................................................................................page 8
SELECT-ALERT ASSEMBLY PARTS LIST
1 - 05000 Electronics Assembly
1 - 05050 Color Lens
4 Screw #6 x 5/8 in.
4 Screw #8-32 x 3/8 in.
2 Screw #6 x 1 1/4 in.
2 Anchor #8-10
2 Screw #6-32 x 1 1/2 in.
1 #8-32 x 1/2 in. tamper screw
1 Tamper wrench
ACCESSORIES
KIT-71100A-W Backbox kit
KIT-E18151 N.C. reed switch and magnet
KIT-SA505 Key switch mounting bracket (includes key switch & 2 keys)
EBAT-9VDC 9 volt battery
KIT-H18075 Additional replacement key

- 3 -
WARNINGS
All units are recommended for indoor use. Unit must be tested periodically to verify the life of
battery. STI recommends you change the 9 Volt battery twice a year. When purchasing a Select-
Alert, you will need to periodically test the connections to make sure audibles function at a sound
level to alert staff. Installer may need to purchase a simple audio-meter, typically available at your
local electronics store, to measure the sound in areas where the alarm is expected to be heard
during normal noise environment. Results from this test may prove it beneficial to purchase
additional Select-Alert units.
All specifications and information shown are current as of publication and subject to change
without notice.
WARRANTY INFORMATION
Three year guarantee against breakage of polycarbonate housing in normal use (one year on
electro mechanical and electronic components).
Electronic warranty form at www.sti-usa.com/wc14.
DIMENSIONS
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
NO
COM
NC
ALARM SWITCH
KEY SWITCH
DC IN -
DC IN +
Install 4/05
FRONT SIDE
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
S1
ALARM TONES
S2
ALARM TIMING
STROBE TIMING
VOLUME
LED QTY 10
LOW BATTERY
INDICATOR LED
TERMINAL STRIP
TAMPER SWITCH
(REAR VIEW)
WIRE ENTRY
BATTERY
BATTERY CABLE
SIREN
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
LED QTY 10
LOW BATTERY
INDICATOR LED
TERMINAL STRIP
TAMPER SWITCH WIRE ENTRY
BATTERY
BATTERY CABLE
SIREN
REMOTE POWER IN
12-24 VDC, 125mA
+
-
OFF ON
**MAIN POWER
CONTROL
ACTIVE STAND BY
ALARM
SWITCH
FORM "C"
DRY CONTACTS
NORMALLY
OPEN
NORMALLY
CLOSED
COM
DRILL
3/16 DIA HOLES
19018 ANCHOR
#8-10
(2) PROVIDED
19039 SCREW
#6 x 1 1/4 in.
(2) PROVIDED
TO KEY MOUNT PLATE OR INTO WALL
BASE PLATE
H18074 SWITCH LOCK
KIT-SA505 KEY SWITCH
MOUNTING BRACKET
SINGLE GANG
ELECTRICAL BOX
#6-32 x 1 1/2 in. SCREW
(2) PROVIDED
TO SINGLE GANG ELECTRICAL BOX
BASE PLATE
05050- LENS COLORS
A - AMBER
B - BLUE
G - GREEN
R - RED
W - WHITE
#8-32 x 3/8 in. SCREW
(4) PROVIDED
05000 ELECTRONICS
ELECTRONICS ASSEMBLY FINAL
INSTALLED
BASE PLATE
2 13/32 in.
19018 ANCHOR
#8-10
(4) PROVIDED
DRILL (4)
3/16 in. DIA HOLES
KIT-SA504 BACKBOX
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19068 SCREW
#6 x 5/8 in.
(4) PROVIDED
BASE PLATE
TO STI BACKBOX 71100A
71100B-W
BRIDGE INSERT
1 31/32 in.
3 9/32 in.
WIRE ACCESS HOLE
TAMPER-PROOF
TOOL (1) PROVIDED
TAMPER-PROOF SCREW
2 13/32 in.
19018 ANCHOR
#8-10
(4) PROVIDED
DRILL (4)
3/16 in. DIA HOLES
KIT-71100A-W BACKBOX
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19068 SCREW
#6 x 5/8 in.
(4) PROVIDED
BASE PLATE
71100B-W
BRIDGE INSERT
1 31/32 in.
DRILL
3/16 DIA HOLES
ANCHOR
#8-10
(2) PROVIDED
#6 x 1 1/4 in. SCREW
(2) PROVIDED
BASE PLATE
H18074 SWITCH LOCK
KIT-SA505 KEY SWITCH
MOUNTING BRACKET
3 9/32 in.
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
REMOTE POWER IN
12-24 VDC, 125mA
+
-
OFF ON
**MAIN POWER
CONTROL
STAND
BY
ALARM
SWITCH
FORM "C"
DRY CONTACTS
NORMALLY OPEN
COM
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
NORMALLY CLOSED
ACTIVE
1.58 in.
2.725 in.
4.75 in.
4.83 in.
3.05 in.
3.22 in.
3.25 in.
4.83 in.
1.58 in.
2.725 in.
4.75 in.
4.83 in.
3.05 in.
3.22 in.
3.25 in.
4.83 in.
3.25 in.
(83mm)
4.83 in.
(123mm)
FRONT SIDE
3.25 in.
(83mm)
4.83 in.
(123mm)
1.58 in.
(40mm)
2.73 in.
(69mm)
1.58 in.
(40mm)
2.73 in.
(69mm)
LENS COVER
BACKPLATE
MOUNTING PLATE
ELECTRONICS
19011 TAMPERPROOF SCREW
KEY SWITCH
LENS COVER
BACKPLATE
KEY SWITCH
MOUNTING PLATE
19011 TAMPERPROOF SCREW
ELECTRONICS
KIT-18075 REPLACEMENT
#801 KEY
#801 KEY
REMOTE POWER IN
12-24 VDC, 125mA
(OPTIONAL)
+
-
OFF ON
**MAIN POWER
CONTROL TO
KEY SWITCH
STAND
BY
REED
SWITCH FROM CABINET
FORM "C"
DRY CONTACTS
NORMALLY OPEN
COM
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
NORMALLY CLOSED
ACTIVE
DRILL (4) 3/16 in. DIA. HOLES IF USING #8-10 ANCHORS.
DRILL (4) 3/32 in. DIA. HOLES WHEN USING #6 SCREWS ONLY.
19018 ANCHOR
#8-10
(4) PROVIDED
SUB-71100A-W
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19060 SCREW
#6-32 x 1 in.
(2) PROVIDED
BASE PLATE
1-24-11
NOTE TO BECK:
This sketch replaces
(Step 5 - Mounting Options VIEW A)
in STI-SA5000 install sheet.
1. Using 5/32 Drill, Drill through the (4) exsisting holes in backbox (one in each corner).
2. Place backbox on wall and mark the mounting hole positions.
3. If using #8-10 anchors, drill 3/16 dia. holes 1 in. deep into wall and press anchor into hole.
If using #6 screws only, drill 3/32 dia. holes 1-1/4 in. deep.
4. Mount backbox to wall using #6 x 1 1/4 screws.
5. Mount base plate as shown using (2) #6-32 x 1 in. screws.
NOTE: If not using STI backbox, make sure surface will depress tamper switch.
ENCLOSURE
ROUTE THE TWO KEY
SWITCH WIRES THROUGH
THE HOLE AS SHOWN
WIRE ACCESS HOLE
ROUTE THE TWO REED
SWITCH WIRES FROM
CABINET THROUGH THE
HOLE AS SHOWN

- 4 -
SPECIFICATIONS
Operating Voltage Internal power 9 VDC battery (not included)
Operating Temperature 32°F-120°
Power Consumption Stand by: 50µA
Siren low volume: 85mA
Siren high volume: 90mA
Strobe: 25mA
Siren Volume Low: 85 dB
High: 100 dB
Alarm Timing Independent control for siren and strobe:
15s, 30s, 60s, continuous
Low Battery Warning LED flash once every 30 seconds
Form C Dry Contacts 0-30VAC/DC, 1 Amp
Contacts reset after longest alarm setting
Key Switch Alarm on: normally closed
Alarm Switch Stand by: normally open contact required
Polycarbonate UL94V-2
Flammability Rating
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
NO
COM
NC
ALARM SWITCH
KEY SWITCH
DC IN -
DC IN +
Install 4/05
FRONT SIDE
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
S1
ALARM TONES
S2
ALARM TIMING
STROBE TIMING
VOLUME
LED QTY 10
LOW BATTERY
INDICATOR LED
TERMINAL STRIP
TAMPER SWITCH
(REAR VIEW)
WIRE ENTRY
BATTERY
BATTERY CABLE
SIREN
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
LED QTY 10
LOW BATTERY
INDICATOR LED
TERMINAL STRIP
TAMPER SWITCH WIRE ENTRY
BATTERY
BATTERY CABLE
SIREN
REMOTE POWER IN
12-24 VDC, 125mA
+
-
OFF ON
**MAIN POWER
CONTROL
ACTIVE STAND BY
ALARM
SWITCH
FORM "C"
DRY CONTACTS
NORMALLY
OPEN
NORMALLY
CLOSED
COM
DRILL
3/16 DIA HOLES
19018 ANCHOR
#8-10
(2) PROVIDED
19039 SCREW
#6 x 1 1/4 in.
(2) PROVIDED
TO KEY MOUNT PLATE OR INTO WALL
BASE PLATE
H18074 SWITCH LOCK
KIT-SA505 KEY SWITCH
MOUNTING BRACKET
SINGLE GANG
ELECTRICAL BOX
#6-32 x 1 1/2 in. SCREW
(2) PROVIDED
TO SINGLE GANG ELECTRICAL BOX
BASE PLATE
05050- LENS COLORS
A - AMBER
B - BLUE
G - GREEN
R - RED
W - WHITE
#8-32 x 3/8 in. SCREW
(4) PROVIDED
05000 ELECTRONICS
ELECTRONICS ASSEMBLY FINAL
INSTALLED
BASE PLATE
2 13/32 in.
19018 ANCHOR
#8-10
(4) PROVIDED
DRILL (4)
3/16 in. DIA HOLES
KIT-SA504 BACKBOX
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19068 SCREW
#6 x 5/8 in.
(4) PROVIDED
BASE PLATE
TO STI BACKBOX 71100A
71100B-W
BRIDGE INSERT
1 31/32 in.
3 9/32 in.
WIRE ACCESS HOLE
TAMPER-PROOF
TOOL (1) PROVIDED
TAMPER-PROOF SCREW
2 13/32 in.
19018 ANCHOR
#8-10
(4) PROVIDED
DRILL (4)
3/16 in. DIA HOLES
KIT-71100A-W BACKBOX
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19068 SCREW
#6 x 5/8 in.
(4) PROVIDED
BASE PLATE
71100B-W
BRIDGE INSERT
1 31/32 in.
DRILL
3/16 DIA HOLES
ANCHOR
#8-10
(2) PROVIDED
#6 x 1 1/4 in. SCREW
(2) PROVIDED
BASE PLATE
H18074 SWITCH LOCK
KIT-SA505 KEY SWITCH
MOUNTING BRACKET
3 9/32 in.
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
REMOTE POWER IN
12-24 VDC, 125mA
+-OFF ON
**MAIN POWER
CONTROL
STAND
BY
ALARM
SWITCH
FORM "C"
DRY CONTACTS
NORMALLY OPEN
COM
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
NORMALLY CLOSED
ACTIVE
1.58 in.
2.725 in.
4.75 in.
4.83 in.
3.05 in.
3.22 in.
3.25 in.
4.83 in.
1.58 in.
2.725 in.
4.75 in.
4.83 in.
3.05 in.
3.22 in.
3.25 in.
4.83 in.
3.25 in.
(83mm)
4.83 in.
(123mm)
FRONT SIDE
3.25 in.
(83mm)
4.83 in.
(123mm)
1.58 in.
(40mm)
2.73 in.
(69mm)
1.58 in.
(40mm)
2.73 in.
(69mm)
LENS COVER
BACKPLATE
MOUNTING PLATE
ELECTRONICS
19011 TAMPERPROOF SCREW
KEY SWITCH
LENS COVER
BACKPLATE
KEY SWITCH
MOUNTING PLATE
19011 TAMPERPROOF SCREW
ELECTRONICS
KIT-18075 REPLACEMENT
#801 KEY
#801 KEY
REMOTE POWER IN
12-24 VDC, 125mA
(OPTIONAL)
+-OFF ON
**MAIN POWER
CONTROL TO
KEY SWITCH
STAND
BY
REED
SWITCH FROM CABINET
FORM "C"
DRY CONTACTS
NORMALLY OPEN
COM
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
NORMALLY CLOSED
ACTIVE
DRILL (4) 3/16 in. DIA. HOLES IF USING #8-10 ANCHORS.
DRILL (4) 3/32 in. DIA. HOLES WHEN USING #6 SCREWS ONLY.
19018 ANCHOR
#8-10
(4) PROVIDED
SUB-71100A-W
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19060 SCREW
#6-32 x 1 in.
(2) PROVIDED
BASE PLATE
1-24-11
NOTE TO BECK:
This sketch replaces
(Step 5 - Mounting Options VIEW A)
in STI-SA5000 install sheet.
1. Using 5/32 Drill, Drill through the (4) exsisting holes in backbox (one in each corner).
2. Place backbox on wall and mark the mounting hole positions.
3. If using #8-10 anchors, drill 3/16 dia. holes 1 in. deep into wall and press anchor into hole.
If using #6 screws only, drill 3/32 dia. holes 1-1/4 in. deep.
4. Mount backbox to wall using #6 x 1 1/4 screws.
5. Mount base plate as shown using (2) #6-32 x 1 in. screws.
NOTE: If not using STI backbox, make sure surface will depress tamper switch.
ENCLOSURE
ROUTE THE TWO KEY
SWITCH WIRES THROUGH
THE HOLE AS SHOWN
WIRE ACCESS HOLE
ROUTE THE TWO REED
SWITCH WIRES FROM
CABINET THROUGH THE
HOLE AS SHOWN
INSTALLATION
Step 1 - Electronic Setup

- 5 -
Step 2 - Alarm Tones - S1
1 0 0 0 0 0BUZZ
2 1 0 0 0 0SLOW ON/OFF
3 0 1 0 0 0SLOW SIREN
4 1 1 0 0 03 BEEP/PAUSE/REPEAT
5 0 0 1 0 0UFO FAST
6 1 0 1 0 0FAST SIREN
7 0 1 1 0 0#5 FAST
8 1 1 1 0 0#2 MEDIUM
9 0 0 0 1 0#5 MEDIUM
10 1 0 0 1 0SWOOP MEDIUM
11 0 1 0 1 0#3 MEDIUM
12 1 1 0 1 0BUZZ TONE
13 0 0 1 1 0STEADY FAST
14 1 0 1 1 0 SWOOP SLOW
15 0 1 1 1 0CONTINUOUS
16 1 1 1 1 0FAST REPEAT
17 0 0 0 0 1STANDARD ALARM
18 1 0 0 0 1#3 FAST
19 0 1 0 0 1#5 SLOW
20 1 1 0 0 1FAST BEEP
21 0 0 1 0 1SOUND A
22 1 0 1 0 1SOUND B
23 0 1 1 0 1SOUND C
24 1 1 1 0 1SOUND D
25 0 0 0 1 1SOUND D LOUD
26 1 0 0 1 1SOUND E
27 0 1 0 1 1SOUND F
28 1 1 0 1 1SOUND G
29 0 0 1 1 1SOUND H
30 1 0 1 1 1#4 LOW
31 0 1 1 1 1SOUND K
32 1 1 1 1 1CONTINUOUS FAST
1 2 3 4 5 1 2 3 4 5
NOTE: Sound may be disabled by
clipping wires to the siren.
THIS WILL VOID ALL WARRANTIES.
Remove two screws on circuit board;
leave enough length of wire to
possibly reattach in the future. Then
insulate wires to prevent shorting to
electronic components.
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
NO
COM
NC
ALARM SWITCH
KEY SWITCH
DC IN -
DC IN +
Install 4/05
FRONT SIDE
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
S1
ALARM TONES
S2
ALARM TIMING
STROBE TIMING
VOLUME
LED QTY 10
LOW BATTERY
INDICATOR LED
TERMINAL STRIP
TAMPER SWITCH
(REAR VIEW)
WIRE ENTRY
BATTERY
BATTERY CABLE
SIREN
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
LED QTY 10
LOW BATTERY
INDICATOR LED
TERMINAL STRIP
TAMPER SWITCH WIRE ENTRY
BATTERY
BATTERY CABLE
SIREN
REMOTE POWER IN
12-24 VDC, 125mA
+
-
OFF ON
**MAIN POWER
CONTROL
ACTIVE STAND BY
ALARM
SWITCH
FORM "C"
DRY CONTACTS
NORMALLY
OPEN
NORMALLY
CLOSED
COM
DRILL
3/16 DIA HOLES
19018 ANCHOR
#8-10
(2) PROVIDED
19039 SCREW
#6 x 1 1/4 in.
(2) PROVIDED
TO KEY MOUNT PLATE OR INTO WALL
BASE PLATE
H18074 SWITCH LOCK
KIT-SA505 KEY SWITCH
MOUNTING BRACKET
SINGLE GANG
ELECTRICAL BOX
#6-32 x 1 1/2 in. SCREW
(2) PROVIDED
TO SINGLE GANG ELECTRICAL BOX
BASE PLATE
05050- LENS COLORS
A - AMBER
B - BLUE
G - GREEN
R - RED
W - WHITE
#8-32 x 3/8 in. SCREW
(4) PROVIDED
05000 ELECTRONICS
ELECTRONICS ASSEMBLY FINAL
INSTALLED
BASE PLATE
2 13/32 in.
19018 ANCHOR
#8-10
(4) PROVIDED
DRILL (4)
3/16 in. DIA HOLES
KIT-SA504 BACKBOX
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19068 SCREW
#6 x 5/8 in.
(4) PROVIDED
BASE PLATE
TO STI BACKBOX 71100A
71100B-W
BRIDGE INSERT
1 31/32 in.
3 9/32 in.
WIRE ACCESS HOLE
TAMPER-PROOF
TOOL (1) PROVIDED
TAMPER-PROOF SCREW
2 13/32 in.
19018 ANCHOR
#8-10
(4) PROVIDED
DRILL (4)
3/16 in. DIA HOLES
KIT-71100A-W BACKBOX
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19068 SCREW
#6 x 5/8 in.
(4) PROVIDED
BASE PLATE
71100B-W
BRIDGE INSERT
1 31/32 in.
DRILL
3/16 DIA HOLES
ANCHOR
#8-10
(2) PROVIDED
#6 x 1 1/4 in. SCREW
(2) PROVIDED
BASE PLATE
H18074 SWITCH LOCK
KIT-SA505 KEY SWITCH
MOUNTING BRACKET
3 9/32 in.
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
REMOTE POWER IN
12-24 VDC, 125mA
+-OFF ON
**MAIN POWER
CONTROL
STAND
BY
ALARM
SWITCH
FORM "C"
DRY CONTACTS
NORMALLY OPEN
COM
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
NORMALLY CLOSED
ACTIVE
1.58 in.
2.725 in.
4.75 in.
4.83 in.
3.05 in.
3.22 in.
3.25 in.
4.83 in.
1.58 in.
2.725 in.
4.75 in.
4.83 in.
3.05 in.
3.22 in.
3.25 in.
4.83 in.
3.25 in.
(83mm)
4.83 in.
(123mm)
FRONT SIDE
3.25 in.
(83mm)
4.83 in.
(123mm)
1.58 in.
(40mm)
2.73 in.
(69mm)
1.58 in.
(40mm)
2.73 in.
(69mm)
LENS COVER
BACKPLATE
MOUNTING PLATE
ELECTRONICS
19011 TAMPERPROOF SCREW
KEY SWITCH
LENS COVER
BACKPLATE
KEY SWITCH
MOUNTING PLATE
19011 TAMPERPROOF SCREW
ELECTRONICS
KIT-18075 REPLACEMENT
#801 KEY
#801 KEY
REMOTE POWER IN
12-24 VDC, 125mA
(OPTIONAL)
+-OFF ON
**MAIN POWER
CONTROL TO
KEY SWITCH
STAND
BY
REED
SWITCH FROM CABINET
FORM "C"
DRY CONTACTS
NORMALLY OPEN
COM
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
NORMALLY CLOSED
ACTIVE
DRILL (4) 3/16 in. DIA. HOLES IF USING #8-10 ANCHORS.
DRILL (4) 3/32 in. DIA. HOLES WHEN USING #6 SCREWS ONLY.
19018 ANCHOR
#8-10
(4) PROVIDED
SUB-71100A-W
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19060 SCREW
#6-32 x 1 in.
(2) PROVIDED
BASE PLATE
1-24-11
NOTE TO BECK:
This sketch replaces
(Step 5 - Mounting Options VIEW A)
in STI-SA5000 install sheet.
1. Using 5/32 Drill, Drill through the (4) exsisting holes in backbox (one in each corner).
2. Place backbox on wall and mark the mounting hole positions.
3. If using #8-10 anchors, drill 3/16 dia. holes 1 in. deep into wall and press anchor into hole.
If using #6 screws only, drill 3/32 dia. holes 1-1/4 in. deep.
4. Mount backbox to wall using #6 x 1 1/4 screws.
5. Mount base plate as shown using (2) #6-32 x 1 in. screws.
NOTE: If not using STI backbox, make sure surface will depress tamper switch.
ENCLOSURE
ROUTE THE TWO KEY
SWITCH WIRES THROUGH
THE HOLE AS SHOWN
WIRE ACCESS HOLE
ROUTE THE TWO REED
SWITCH WIRES FROM
CABINET THROUGH THE
HOLE AS SHOWN
Step 3 - Alarm Timing and Volume - S2
WIRES TO SIREN
1
ALARM TIMING VOLUME
STROBE TIMING
ON
OFF
1
2345
0
15 seconds 1 1 1 1 High
30 seconds 1 0 1 0 1
60 seconds 0 1 0 1 Low
Continuous 0 0 0 0 0
Alarm Siren Strobe Volume
Timing 1 2 3 4 5
*
*
1 = ON 0 = OFF
Factory default settings

- 6 -
Step 4 - Terminal Strip Connections
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
NO
COM
NC
ALARM SWITCH
KEY SWITCH
DC IN -
DC IN +
Install 4/05
FRONT SIDE
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
S1
ALARM TONES
S2
ALARM TIMING
STROBE TIMING
VOLUME
LED QTY 10
LOW BATTERY
INDICATOR LED
TERMINAL STRIP
TAMPER SWITCH
(REAR VIEW)
WIRE ENTRY
BATTERY
BATTERY CABLE
SIREN
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
LED QTY 10
LOW BATTERY
INDICATOR LED
TERMINAL STRIP
TAMPER SWITCH WIRE ENTRY
BATTERY
BATTERY CABLE
SIREN
REMOTE POWER IN
12-24 VDC, 125mA
+
-
OFF ON
**MAIN POWER
CONTROL
ACTIVE STAND BY
ALARM
SWITCH
FORM "C"
DRY CONTACTS
NORMALLY
OPEN
NORMALLY
CLOSED
COM
DRILL
3/16 DIA HOLES
19018 ANCHOR
#8-10
(2) PROVIDED
19039 SCREW
#6 x 1 1/4 in.
(2) PROVIDED
TO KEY MOUNT PLATE OR INTO WALL
BASE PLATE
H18074 SWITCH LOCK
KIT-SA505 KEY SWITCH
MOUNTING BRACKET
SINGLE GANG
ELECTRICAL BOX
#6-32 x 1 1/2 in. SCREW
(2) PROVIDED
TO SINGLE GANG ELECTRICAL BOX
BASE PLATE
05050- LENS COLORS
A - AMBER
B - BLUE
G - GREEN
R - RED
W - WHITE
#8-32 x 3/8 in. SCREW
(4) PROVIDED
05000 ELECTRONICS
ELECTRONICS ASSEMBLY FINAL
INSTALLED
BASE PLATE
2 13/32 in.
19018 ANCHOR
#8-10
(4) PROVIDED
DRILL (4)
3/16 in. DIA HOLES
KIT-SA504 BACKBOX
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19068 SCREW
#6 x 5/8 in.
(4) PROVIDED
BASE PLATE
TO STI BACKBOX 71100A
71100B-W
BRIDGE INSERT
1 31/32 in.
3 9/32 in.
WIRE ACCESS HOLE
TAMPER-PROOF
TOOL (1) PROVIDED
TAMPER-PROOF SCREW
2 13/32 in.
19018 ANCHOR
#8-10
(4) PROVIDED
DRILL (4)
3/16 in. DIA HOLES
KIT-71100A-W BACKBOX
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19068 SCREW
#6 x 5/8 in.
(4) PROVIDED
BASE PLATE
71100B-W
BRIDGE INSERT
1 31/32 in.
DRILL
3/16 DIA HOLES
ANCHOR
#8-10
(2) PROVIDED
#6 x 1 1/4 in. SCREW
(2) PROVIDED
BASE PLATE
H18074 SWITCH LOCK
KIT-SA505 KEY SWITCH
MOUNTING BRACKET
3 9/32 in.
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
REMOTE POWER IN
12-24 VDC, 125mA
+-OFF ON
**MAIN POWER
CONTROL
STAND
BY
ALARM
SWITCH
FORM "C"
DRY CONTACTS
NORMALLY OPEN
COM
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
NORMALLY CLOSED
ACTIVE
1.58 in.
2.725 in.
4.75 in.
4.83 in.
3.05 in.
3.22 in.
3.25 in.
4.83 in.
1.58 in.
2.725 in.
4.75 in.
4.83 in.
3.05 in.
3.22 in.
3.25 in.
4.83 in.
3.25 in.
(83mm)
4.83 in.
(123mm)
FRONT SIDE
3.25 in.
(83mm)
4.83 in.
(123mm)
1.58 in.
(40mm)
2.73 in.
(69mm)
1.58 in.
(40mm)
2.73 in.
(69mm)
LENS COVER
BACKPLATE
MOUNTING PLATE
ELECTRONICS
19011 TAMPERPROOF SCREW
KEY SWITCH
LENS COVER
BACKPLATE
KEY SWITCH
MOUNTING PLATE
19011 TAMPERPROOF SCREW
ELECTRONICS
KIT-18075 REPLACEMENT
#801 KEY
#801 KEY
REMOTE POWER IN
12-24 VDC, 125mA
(OPTIONAL)
+-OFF ON
**MAIN POWER
CONTROL TO
KEY SWITCH
STAND
BY
REED
SWITCH FROM CABINET
FORM "C"
DRY CONTACTS
NORMALLY OPEN
COM
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
NORMALLY CLOSED
ACTIVE
DRILL (4) 3/16 in. DIA. HOLES IF USING #8-10 ANCHORS.
DRILL (4) 3/32 in. DIA. HOLES WHEN USING #6 SCREWS ONLY.
19018 ANCHOR
#8-10
(4) PROVIDED
SUB-71100A-W
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19060 SCREW
#6-32 x 1 in.
(2) PROVIDED
BASE PLATE
1-24-11
NOTE TO BECK:
This sketch replaces
(Step 5 - Mounting Options VIEW A)
in STI-SA5000 install sheet.
1. Using 5/32 Drill, Drill through the (4) exsisting holes in backbox (one in each corner).
2. Place backbox on wall and mark the mounting hole positions.
3. If using #8-10 anchors, drill 3/16 dia. holes 1 in. deep into wall and press anchor into hole.
If using #6 screws only, drill 3/32 dia. holes 1-1/4 in. deep.
4. Mount backbox to wall using #6 x 1 1/4 screws.
5. Mount base plate as shown using (2) #6-32 x 1 in. screws.
NOTE: If not using STI backbox, make sure surface will depress tamper switch.
ENCLOSURE
ROUTE THE TWO KEY
SWITCH WIRES THROUGH
THE HOLE AS SHOWN
WIRE ACCESS HOLE
ROUTE THE TWO REED
SWITCH WIRES FROM
CABINET THROUGH THE
HOLE AS SHOWN
“DC IN” are the only polarity
sensitive terminals. When
external power is used, battery
will act as a backup. “Dry
Contacts: NC, COM, NO” are used
for remote alarm monitoring.
**Shipped with jumper wire
installed. Remove to add key
switch or other main power on/off
switch.
If using power only to trigger
alarm, add jumper to the alarm
switch terminals. If not using key
switch or other main power on/off,
key switch must also have jumper.
Step 5 - Mounting Options
A) To STI Backbox SUB-71100A-W
1.Using 5/32 drill, drill through the (4) existing holes in back box (one in each corner).
2.Place back box on wall and mark the mounting hole positions.
3.If using #8-10 anchors, drill 3/16 dia. holes 1 in. deep into wall and press anchor into hole. If using #6 screws only,
drill 3/32 dia. holes 1 ¼ in. deep.
4.Mount back box to wall using #6 x 1 ¼ in. screws.
5.Mount base plate as shown using (2) #6-32 x 1 in. screws.
Note: If not using STI back box, make sure surface will depress tamper switch.
A
REMOVE THESE TABS
FROM ALL FOUR CORNERS
#6 x 1 1/4 in. SCREW
(4) PROVIDED
#6-32 X 5/8 in. SCREW
(2) PROVIDED
BASE PLATE
DRILL (4) 3/16 in. DIA. HOLES
IF USING #8-10 ANCHORS
DRILL (4) 3/32 in. DIA. HOLES
WHEN USING #6 SCREWS ONLY
#8-10 ANCHOR
(4) PROVIDED KIT-SA504
BACKBOX
DETAIL A

- 7 -
B) To Key Mount Plate or into Wall without Electrical Box
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
NO
COM
NC
ALARM SWITCH
KEY SWITCH
DC IN -
DC IN +
Install 4/05
FRONT SIDE
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
S1
ALARM TONES
S2
ALARM TIMING
STROBE TIMING
VOLUME
LED QTY 10
LOW BATTERY
INDICATOR LED
TERMINAL STRIP
TAMPER SWITCH
(REAR VIEW)
WIRE ENTRY
BATTERY
BATTERY CABLE
SIREN
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
LED QTY 10
LOW BATTERY
INDICATOR LED
TERMINAL STRIP
TAMPER SWITCH WIRE ENTRY
BATTERY
BATTERY CABLE
SIREN
REMOTE POWER IN
12-24 VDC, 125mA
+
-
OFF ON
**MAIN POWER
CONTROL
ACTIVE STAND BY
ALARM
SWITCH
FORM "C"
DRY CONTACTS
NORMALLY
OPEN
NORMALLY
CLOSED
COM
DRILL
3/16 DIA HOLES
19018 ANCHOR
#8-10
(2) PROVIDED
19039 SCREW
#6 x 1 1/4 in.
(2) PROVIDED
TO KEY MOUNT PLATE OR INTO WALL
BASE PLATE
H18074 SWITCH LOCK
KIT-SA505 KEY SWITCH
MOUNTING BRACKET
SINGLE GANG
ELECTRICAL BOX
#6-32 x 1 1/2 in. SCREW
(2) PROVIDED
TO SINGLE GANG ELECTRICAL BOX
BASE PLATE
05050- LENS COLORS
A - AMBER
B - BLUE
G - GREEN
R - RED
W - WHITE
#8-32 x 3/8 in. SCREW
(4) PROVIDED
05000 ELECTRONICS
ELECTRONICS ASSEMBLY FINAL
INSTALLED
BASE PLATE
2 13/32 in.
19018 ANCHOR
#8-10
(4) PROVIDED
DRILL (4)
3/16 in. DIA HOLES
KIT-SA504 BACKBOX
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19068 SCREW
#6 x 5/8 in.
(4) PROVIDED
BASE PLATE
TO STI BACKBOX 71100A
71100B-W
BRIDGE INSERT
1 31/32 in.
3 9/32 in.
WIRE ACCESS HOLE
TAMPER-PROOF
TOOL (1) PROVIDED
TAMPER-PROOF SCREW
2 13/32 in.
19018 ANCHOR
#8-10
(4) PROVIDED
DRILL (4)
3/16 in. DIA HOLES
KIT-71100A-W BACKBOX
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19068 SCREW
#6 x 5/8 in.
(4) PROVIDED
BASE PLATE
71100B-W
BRIDGE INSERT
1 31/32 in.
DRILL
3/16 DIA HOLES
ANCHOR
#8-10
(2) PROVIDED
#6 x 1 1/4 in. SCREW
(2) PROVIDED
BASE PLATE
H18074 SWITCH LOCK
KIT-SA505 KEY SWITCH
MOUNTING BRACKET
3 9/32 in.
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
REMOTE POWER IN
12-24 VDC, 125mA
+-OFF ON
**MAIN POWER
CONTROL
STAND
BY
ALARM
SWITCH
FORM "C"
DRY CONTACTS
NORMALLY OPEN
COM
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
NORMALLY CLOSED
ACTIVE
1.58 in.
2.725 in.
4.75 in.
4.83 in.
3.05 in.
3.22 in.
3.25 in.
4.83 in.
1.58 in.
2.725 in.
4.75 in.
4.83 in.
3.05 in.
3.22 in.
3.25 in.
4.83 in.
3.25 in.
(83mm)
4.83 in.
(123mm)
FRONT SIDE
3.25 in.
(83mm)
4.83 in.
(123mm)
1.58 in.
(40mm)
2.73 in.
(69mm)
1.58 in.
(40mm)
2.73 in.
(69mm)
LENS COVER
BACKPLATE
MOUNTING PLATE
ELECTRONICS
19011 TAMPERPROOF SCREW
KEY SWITCH
LENS COVER
BACKPLATE
KEY SWITCH
MOUNTING PLATE
19011 TAMPERPROOF SCREW
ELECTRONICS
KIT-18075 REPLACEMENT
#801 KEY
#801 KEY
REMOTE POWER IN
12-24 VDC, 125mA
(OPTIONAL)
+-OFF ON
**MAIN POWER
CONTROL TO
KEY SWITCH
STAND
BY
REED
SWITCH FROM CABINET
FORM "C"
DRY CONTACTS
NORMALLY OPEN
COM
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
NORMALLY CLOSED
ACTIVE
DRILL (4) 3/16 in. DIA. HOLES IF USING #8-10 ANCHORS.
DRILL (4) 3/32 in. DIA. HOLES WHEN USING #6 SCREWS ONLY.
19018 ANCHOR
#8-10
(4) PROVIDED
SUB-71100A-W
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19060 SCREW
#6-32 x 1 in.
(2) PROVIDED
BASE PLATE
1-24-11
NOTE TO BECK:
This sketch replaces
(Step 5 - Mounting Options VIEW A)
in STI-SA5000 install sheet.
1. Using 5/32 Drill, Drill through the (4) exsisting holes in backbox (one in each corner).
2. Place backbox on wall and mark the mounting hole positions.
3. If using #8-10 anchors, drill 3/16 dia. holes 1 in. deep into wall and press anchor into hole.
If using #6 screws only, drill 3/32 dia. holes 1-1/4 in. deep.
4. Mount backbox to wall using #6 x 1 1/4 screws.
5. Mount base plate as shown using (2) #6-32 x 1 in. screws.
NOTE: If not using STI backbox, make sure surface will depress tamper switch.
ENCLOSURE
ROUTE THE TWO KEY
SWITCH WIRES THROUGH
THE HOLE AS SHOWN
WIRE ACCESS HOLE
ROUTE THE TWO REED
SWITCH WIRES FROM
CABINET THROUGH THE
HOLE AS SHOWN
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
NO
COM
NC
ALARM SWITCH
KEY SWITCH
DC IN -
DC IN +
Install 4/05
FRONT SIDE
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
S1
ALARM TONES
S2
ALARM TIMING
STROBE TIMING
VOLUME
LED QTY 10
LOW BATTERY
INDICATOR LED
TERMINAL STRIP
TAMPER SWITCH
(REAR VIEW)
WIRE ENTRY
BATTERY
BATTERY CABLE
SIREN
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
LED QTY 10
LOW BATTERY
INDICATOR LED
TERMINAL STRIP
TAMPER SWITCH WIRE ENTRY
BATTERY
BATTERY CABLE
SIREN
REMOTE POWER IN
12-24 VDC, 125mA
+
-
OFF ON
**MAIN POWER
CONTROL
ACTIVE STAND BY
ALARM
SWITCH
FORM "C"
DRY CONTACTS
NORMALLY
OPEN
NORMALLY
CLOSED
COM
DRILL
3/16 DIA HOLES
19018 ANCHOR
#8-10
(2) PROVIDED
19039 SCREW
#6 x 1 1/4 in.
(2) PROVIDED
TO KEY MOUNT PLATE OR INTO WALL
BASE PLATE
H18074 SWITCH LOCK
KIT-SA505 KEY SWITCH
MOUNTING BRACKET
SINGLE GANG
ELECTRICAL BOX
#6-32 x 1 1/2 in. SCREW
(2) PROVIDED
TO SINGLE GANG ELECTRICAL BOX
BASE PLATE
05050- LENS COLORS
A - AMBER
B - BLUE
G - GREEN
R - RED
W - WHITE
#8-32 x 3/8 in. SCREW
(4) PROVIDED
05000 ELECTRONICS
ELECTRONICS ASSEMBLY FINAL
INSTALLED
BASE PLATE
2 13/32 in.
19018 ANCHOR
#8-10
(4) PROVIDED
DRILL (4)
3/16 in. DIA HOLES
KIT-SA504 BACKBOX
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19068 SCREW
#6 x 5/8 in.
(4) PROVIDED
BASE PLATE
TO STI BACKBOX 71100A
71100B-W
BRIDGE INSERT
1 31/32 in.
3 9/32 in.
WIRE ACCESS HOLE
TAMPER-PROOF
TOOL (1) PROVIDED
TAMPER-PROOF SCREW
2 13/32 in.
19018 ANCHOR
#8-10
(4) PROVIDED
DRILL (4)
3/16 in. DIA HOLES
KIT-71100A-W BACKBOX
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19068 SCREW
#6 x 5/8 in.
(4) PROVIDED
BASE PLATE
71100B-W
BRIDGE INSERT
1 31/32 in.
DRILL
3/16 DIA HOLES
ANCHOR
#8-10
(2) PROVIDED
#6 x 1 1/4 in. SCREW
(2) PROVIDED
BASE PLATE
H18074 SWITCH LOCK
KIT-SA505 KEY SWITCH
MOUNTING BRACKET
3 9/32 in.
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
REMOTE POWER IN
12-24 VDC, 125mA
+-OFF ON
**MAIN POWER
CONTROL
STAND
BY
ALARM
SWITCH
FORM "C"
DRY CONTACTS
NORMALLY OPEN
COM
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
NORMALLY CLOSED
ACTIVE
1.58 in.
2.725 in.
4.75 in.
4.83 in.
3.05 in.
3.22 in.
3.25 in.
4.83 in.
1.58 in.
2.725 in.
4.75 in.
4.83 in.
3.05 in.
3.22 in.
3.25 in.
4.83 in.
3.25 in.
(83mm)
4.83 in.
(123mm)
FRONT SIDE
3.25 in.
(83mm)
4.83 in.
(123mm)
1.58 in.
(40mm)
2.73 in.
(69mm)
1.58 in.
(40mm)
2.73 in.
(69mm)
LENS COVER
BACKPLATE
MOUNTING PLATE
ELECTRONICS
19011 TAMPERPROOF SCREW
KEY SWITCH
LENS COVER
BACKPLATE
KEY SWITCH
MOUNTING PLATE
19011 TAMPERPROOF SCREW
ELECTRONICS
KIT-18075 REPLACEMENT
#801 KEY
#801 KEY
REMOTE POWER IN
12-24 VDC, 125mA
(OPTIONAL)
+-OFF ON
**MAIN POWER
CONTROL TO
KEY SWITCH
STAND
BY
REED
SWITCH FROM CABINET
FORM "C"
DRY CONTACTS
NORMALLY OPEN
COM
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
NORMALLY CLOSED
ACTIVE
DRILL (4) 3/16 in. DIA. HOLES IF USING #8-10 ANCHORS.
DRILL (4) 3/32 in. DIA. HOLES WHEN USING #6 SCREWS ONLY.
19018 ANCHOR
#8-10
(4) PROVIDED
SUB-71100A-W
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19060 SCREW
#6-32 x 1 in.
(2) PROVIDED
BASE PLATE
1-24-11
NOTE TO BECK:
This sketch replaces
(Step 5 - Mounting Options VIEW A)
in STI-SA5000 install sheet.
1. Using 5/32 Drill, Drill through the (4) exsisting holes in backbox (one in each corner).
2. Place backbox on wall and mark the mounting hole positions.
3. If using #8-10 anchors, drill 3/16 dia. holes 1 in. deep into wall and press anchor into hole.
If using #6 screws only, drill 3/32 dia. holes 1-1/4 in. deep.
4. Mount backbox to wall using #6 x 1 1/4 screws.
5. Mount base plate as shown using (2) #6-32 x 1 in. screws.
NOTE: If not using STI backbox, make sure surface will depress tamper switch.
ENCLOSURE
ROUTE THE TWO KEY
SWITCH WIRES THROUGH
THE HOLE AS SHOWN
WIRE ACCESS HOLE
ROUTE THE TWO REED
SWITCH WIRES FROM
CABINET THROUGH THE
HOLE AS SHOWN
C) To Single Gang Electrical Box
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
NO
COM
NC
ALARM SWITCH
KEY SWITCH
DC IN -
DC IN +
Install 4/05
FRONT SIDE
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
S1
ALARM TONES
S2
ALARM TIMING
STROBE TIMING
VOLUME
LED QTY 10
LOW BATTERY
INDICATOR LED
TERMINAL STRIP
TAMPER SWITCH
(REAR VIEW)
WIRE ENTRY
BATTERY
BATTERY CABLE
SIREN
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
LED QTY 10
LOW BATTERY
INDICATOR LED
TERMINAL STRIP
TAMPER SWITCH WIRE ENTRY
BATTERY
BATTERY CABLE
SIREN
REMOTE POWER IN
12-24 VDC, 125mA
+
-
OFF ON
**MAIN POWER
CONTROL
ACTIVE STAND BY
ALARM
SWITCH
FORM "C"
DRY CONTACTS
NORMALLY
OPEN
NORMALLY
CLOSED
COM
DRILL
3/16 DIA HOLES
19018 ANCHOR
#8-10
(2) PROVIDED
19039 SCREW
#6 x 1 1/4 in.
(2) PROVIDED
TO KEY MOUNT PLATE OR INTO WALL
BASE PLATE
H18074 SWITCH LOCK
KIT-SA505 KEY SWITCH
MOUNTING BRACKET
SINGLE GANG
ELECTRICAL BOX
#6-32 x 1 1/2 in. SCREW
(2) PROVIDED
TO SINGLE GANG ELECTRICAL BOX
BASE PLATE
05050- LENS COLORS
A - AMBER
B - BLUE
G - GREEN
R - RED
W - WHITE
#8-32 x 3/8 in. SCREW
(4) PROVIDED
05000 ELECTRONICS
ELECTRONICS ASSEMBLY FINAL
INSTALLED
BASE PLATE
2 13/32 in.
19018 ANCHOR
#8-10
(4) PROVIDED
DRILL (4)
3/16 in. DIA HOLES
KIT-SA504 BACKBOX
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19068 SCREW
#6 x 5/8 in.
(4) PROVIDED
BASE PLATE
TO STI BACKBOX 71100A
71100B-W
BRIDGE INSERT
1 31/32 in.
3 9/32 in.
WIRE ACCESS HOLE
TAMPER-PROOF
TOOL (1) PROVIDED
TAMPER-PROOF SCREW
2 13/32 in.
19018 ANCHOR
#8-10
(4) PROVIDED
DRILL (4)
3/16 in. DIA HOLES
KIT-71100A-W BACKBOX
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19068 SCREW
#6 x 5/8 in.
(4) PROVIDED
BASE PLATE
71100B-W
BRIDGE INSERT
1 31/32 in.
DRILL
3/16 DIA HOLES
ANCHOR
#8-10
(2) PROVIDED
#6 x 1 1/4 in. SCREW
(2) PROVIDED
BASE PLATE
H18074 SWITCH LOCK
KIT-SA505 KEY SWITCH
MOUNTING BRACKET
3 9/32 in.
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
REMOTE POWER IN
12-24 VDC, 125mA
+-OFF ON
**MAIN POWER
CONTROL
STAND
BY
ALARM
SWITCH
FORM "C"
DRY CONTACTS
NORMALLY OPEN
COM
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
NORMALLY CLOSED
ACTIVE
1.58 in.
2.725 in.
4.75 in.
4.83 in.
3.05 in.
3.22 in.
3.25 in.
4.83 in.
1.58 in.
2.725 in.
4.75 in.
4.83 in.
3.05 in.
3.22 in.
3.25 in.
4.83 in.
3.25 in.
(83mm)
4.83 in.
(123mm)
FRONT SIDE
3.25 in.
(83mm)
4.83 in.
(123mm)
1.58 in.
(40mm)
2.73 in.
(69mm)
1.58 in.
(40mm)
2.73 in.
(69mm)
LENS COVER
BACKPLATE
MOUNTING PLATE
ELECTRONICS
19011 TAMPERPROOF SCREW
KEY SWITCH
LENS COVER
BACKPLATE
KEY SWITCH
MOUNTING PLATE
19011 TAMPERPROOF SCREW
ELECTRONICS
KIT-18075 REPLACEMENT
#801 KEY
#801 KEY
REMOTE POWER IN
12-24 VDC, 125mA
(OPTIONAL)
+-OFF ON
**MAIN POWER
CONTROL TO
KEY SWITCH
STAND
BY
REED
SWITCH FROM CABINET
FORM "C"
DRY CONTACTS
NORMALLY OPEN
COM
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
NORMALLY CLOSED
ACTIVE
DRILL (4) 3/16 in. DIA. HOLES IF USING #8-10 ANCHORS.
DRILL (4) 3/32 in. DIA. HOLES WHEN USING #6 SCREWS ONLY.
19018 ANCHOR
#8-10
(4) PROVIDED
SUB-71100A-W
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19060 SCREW
#6-32 x 1 in.
(2) PROVIDED
BASE PLATE
1-24-11
NOTE TO BECK:
This sketch replaces
(Step 5 - Mounting Options VIEW A)
in STI-SA5000 install sheet.
1. Using 5/32 Drill, Drill through the (4) exsisting holes in backbox (one in each corner).
2. Place backbox on wall and mark the mounting hole positions.
3. If using #8-10 anchors, drill 3/16 dia. holes 1 in. deep into wall and press anchor into hole.
If using #6 screws only, drill 3/32 dia. holes 1-1/4 in. deep.
4. Mount backbox to wall using #6 x 1 1/4 screws.
5. Mount base plate as shown using (2) #6-32 x 1 in. screws.
NOTE: If not using STI backbox, make sure surface will depress tamper switch.
ENCLOSURE
ROUTE THE TWO KEY
SWITCH WIRES THROUGH
THE HOLE AS SHOWN
WIRE ACCESS HOLE
ROUTE THE TWO REED
SWITCH WIRES FROM
CABINET THROUGH THE
HOLE AS SHOWN

2306 Airport Rd • Waterford, MI 48327, USA
Phone: [phone] • Fax: [phone]
[email protected] • www.sti-usa.com
Safety Technology International Ltd
Taylor House • 34 Sherwood Road • Bromsgrove
Worcestershire • B60 3DR • England • Tel: [phone]
Fax: [phone] • [email protected] • www.sti-europe.com
Printed in USA Inst. Sht. SA5000, Sept2015
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
NO
COM
NC
ALARM SWITCH
KEY SWITCH
DC IN -
DC IN +
Install 4/05
FRONT SIDE
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
S1
ALARM TONES
S2
ALARM TIMING
STROBE TIMING
VOLUME
LED QTY 10
LOW BATTERY
INDICATOR LED
TERMINAL STRIP
TAMPER SWITCH
(REAR VIEW)
WIRE ENTRY
BATTERY
BATTERY CABLE
SIREN
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
LED QTY 10
LOW BATTERY
INDICATOR LED
TERMINAL STRIP
TAMPER SWITCH WIRE ENTRY
BATTERY
BATTERY CABLE
SIREN
REMOTE POWER IN
12-24 VDC, 125mA
+
-
OFF ON
**MAIN POWER
CONTROL
ACTIVE STAND BY
ALARM
SWITCH
FORM "C"
DRY CONTACTS
NORMALLY
OPEN
NORMALLY
CLOSED
COM
DRILL
3/16 DIA HOLES
19018 ANCHOR
#8-10
(2) PROVIDED
19039 SCREW
#6 x 1 1/4 in.
(2) PROVIDED
TO KEY MOUNT PLATE OR INTO WALL
BASE PLATE
H18074 SWITCH LOCK
KIT-SA505 KEY SWITCH
MOUNTING BRACKET
SINGLE GANG
ELECTRICAL BOX
#6-32 x 1 1/2 in. SCREW
(2) PROVIDED
TO SINGLE GANG ELECTRICAL BOX
BASE PLATE
05050- LENS COLORS
A - AMBER
B - BLUE
G - GREEN
R - RED
W - WHITE
#8-32 x 3/8 in. SCREW
(4) PROVIDED
05000 ELECTRONICS
ELECTRONICS ASSEMBLY FINAL
INSTALLED
BASE PLATE
2 13/32 in.
19018 ANCHOR
#8-10
(4) PROVIDED
DRILL (4)
3/16 in. DIA HOLES
KIT-SA504 BACKBOX
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19068 SCREW
#6 x 5/8 in.
(4) PROVIDED
BASE PLATE
TO STI BACKBOX 71100A
71100B-W
BRIDGE INSERT
1 31/32 in.
3 9/32 in.
WIRE ACCESS HOLE
TAMPER-PROOF
TOOL (1) PROVIDED
TAMPER-PROOF SCREW
2 13/32 in.
19018 ANCHOR
#8-10
(4) PROVIDED
DRILL (4)
3/16 in. DIA HOLES
KIT-71100A-W BACKBOX
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19068 SCREW
#6 x 5/8 in.
(4) PROVIDED
BASE PLATE
71100B-W
BRIDGE INSERT
1 31/32 in.
DRILL
3/16 DIA HOLES
ANCHOR
#8-10
(2) PROVIDED
#6 x 1 1/4 in. SCREW
(2) PROVIDED
BASE PLATE
H18074 SWITCH LOCK
KIT-SA505 KEY SWITCH
MOUNTING BRACKET
3 9/32 in.
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
REMOTE POWER IN
12-24 VDC, 125mA
+-OFF ON
**MAIN POWER
CONTROL
STAND
BY
ALARM
SWITCH
FORM "C"
DRY CONTACTS
NORMALLY OPEN
COM
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
NORMALLY CLOSED
ACTIVE
1.58 in.
2.725 in.
4.75 in.
4.83 in.
3.05 in.
3.22 in.
3.25 in.
4.83 in.
1.58 in.
2.725 in.
4.75 in.
4.83 in.
3.05 in.
3.22 in.
3.25 in.
4.83 in.
3.25 in.
(83mm)
4.83 in.
(123mm)
FRONT SIDE
3.25 in.
(83mm)
4.83 in.
(123mm)
1.58 in.
(40mm)
2.73 in.
(69mm)
1.58 in.
(40mm)
2.73 in.
(69mm)
LENS COVER
BACKPLATE
MOUNTING PLATE
ELECTRONICS
19011 TAMPERPROOF SCREW
KEY SWITCH
LENS COVER
BACKPLATE
KEY SWITCH
MOUNTING PLATE
19011 TAMPERPROOF SCREW
ELECTRONICS
KIT-18075 REPLACEMENT
#801 KEY
#801 KEY
REMOTE POWER IN
12-24 VDC, 125mA
(OPTIONAL)
+-OFF ON
**MAIN POWER
CONTROL TO
KEY SWITCH
STAND
BY
REED
SWITCH FROM CABINET
FORM "C"
DRY CONTACTS
NORMALLY OPEN
COM
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
NORMALLY CLOSED
ACTIVE
DRILL (4) 3/16 in. DIA. HOLES IF USING #8-10 ANCHORS.
DRILL (4) 3/32 in. DIA. HOLES WHEN USING #6 SCREWS ONLY.
19018 ANCHOR
#8-10
(4) PROVIDED
SUB-71100A-W
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19060 SCREW
#6-32 x 1 in.
(2) PROVIDED
BASE PLATE
1-24-11
NOTE TO BECK:
This sketch replaces
(Step 5 - Mounting Options VIEW A)
in STI-SA5000 install sheet.
1. Using 5/32 Drill, Drill through the (4) exsisting holes in backbox (one in each corner).
2. Place backbox on wall and mark the mounting hole positions.
3. If using #8-10 anchors, drill 3/16 dia. holes 1 in. deep into wall and press anchor into hole.
If using #6 screws only, drill 3/32 dia. holes 1-1/4 in. deep.
4. Mount backbox to wall using #6 x 1 1/4 screws.
5. Mount base plate as shown using (2) #6-32 x 1 in. screws.
NOTE: If not using STI backbox, make sure surface will depress tamper switch.
ENCLOSURE
ROUTE THE TWO KEY
SWITCH WIRES THROUGH
THE HOLE AS SHOWN
WIRE ACCESS HOLE
ROUTE THE TWO REED
SWITCH WIRES FROM
CABINET THROUGH THE
HOLE AS SHOWN
Step 6 - Electronics Final Assembly
Step 7 - Operation
Wiring: After mounting
circuit board assembly,
connect wires. Refer to
terminal strip connections
(step 4).
Lens installation: Slide
lip of lens behind circuit
board mounting plate.
Rotate lens into position.
Secure with tamperproof
screw and special wrench.
• Turnkeyswitchontoarm.
• Cyclekeyswitchtoresetalarm.
• Alarmwillsoundwhencoverisremoved,unitisremovedfromthewallorcabinetisopened
(alarm switch is electronically closed).
• Toservice,turnkeyswitchoff.