Salamander SYNERGY 229 User manual

TM
SYNERGY 229
Twin Assembly
Includes:
(1) Twin 20 Unit
(2) S20 Side Panels
(2) S10 Doors
(1) Double-Width Shelf
Salamander Designs Ltd. • 800-535-5659 • www.SalamanderDesigns.com ©2008 Salamander Designs Ltd. Synergy System, Patented.
Limited Warranty
Five full years Salamander Designs Ltd will repair or replace, at our option, any product defective in materials or craftsmanship. Salamander Designs Ltd. will not be responsible for any damage to or destruction of other
equipment consequential to our equipment failure. Defective product must be given Return Authorization and is to be returned to the factory prepaid, in the original carton and packing material. Any damage incurred in
a shipment not in original packaging shall be the responsibility of the owner. Warranty repairs will be returned prepaid, via UPS within the continental U.S.A. only.
Doc No. 500-615/v8.12 229 -1/4
BEFORE YOU BEGIN:
• Unpackallpartsandreadinstructionscarefullybeforebeginning.
•Shelfpegsanddoorhingesmustslideintothechannelsofthepostinthecorrectorder.
They cannot be removed individually without disassembling the whole unit.
1
90O
B.Connect Post
Screw foot with metal washer through bottom
shelf and into the end of each extruded post.
Hand tighten fully and use wrench to tighten
nut onto underside of shelf.
A.Square Post
Square the post to the bottom shelf.
Connect Posts to Bottom Shelf
!
!
Short Post
WARNING: Tighten by screwing the leveler foot NOT the post.
Leveler Foot Hex Nut
Washer

12345 6789
S20/
SVDO
REARP ANEL
4 1/2
"
6"
8"
www.salamanderdesigns.com
EXTENDED
REARP ANEL
S30
/S40
REARP ANEL
Doc No. 500-615/v8.12 229 - 2/4
C
2 Installing Hardware
D.Heavy Duty Bracket
Install heavy duty brackets down outer
posts to support the double-width shelf.
Place rubber shelf tabs through bracket.
A.Bottom Door Hinges
Slide the bottom door hinge
plates through the front post
channels.
B. Door Stops
Insert one left and one right door stop
down center post.
C. Top Door Hinges
Slide the top door hinge plates
through the front post channels,
aligning with bottom door hinges.
D
A
A B
A.Insert Hardware
Combine the 1” threaded studs with flat nuts.
Slide 2 sets of hardware down the two outside
posts and 4 sets down the center post. Allow
studs to remain loose at bottom of post.
B.Position & Secure Studs
Align the Spacer Tool at the top of each post,
then position top studs through the small “Rear
Panel” hole. Repeat this step with the bottom
studs aligning the Tool along the bottom of post
to set spacing for cable passage. Use the hex key
to secure the top and bottom studs to the posts.
C.Place Rear Panels
Secure each panel in place with thumb nuts.
Attach Rear Panels
3
4X
2X 2X
C
A
D
B
1 2 3 4 5 6 7 8 9
S20 / SVDO
REAR PANEL
4
1/2 "
6"
8"
www.salamanderdesigns.com
EXTENDE
D
REAR PANEL
S30 / S40
REAR PANEL
SPACER
TOOL
1 2 3 4 5 6 7 8 9
S20 / SVDO
REAR PANEL
4
1/2
"
6"
8"
www.salamanderdesigns.com
EXTENDED
RE
AR PANEL
S30 / S40
REAR PANEL
SPACER
TOOL
1 2 3 4 5 6 7 8 9
S
20 / S
VDO
R
E
AR
PANE
L
4
1/2
"
6"
8"
www.salamanderdesigns.com
E
XTE
NDE
D
R
E
AR
PANE
L
S30 / S
40
R
E
AR
PANE
L
SPACER
TOOL
To ease installation of rear
panels, gently place the unit
face down on the floor to
improve aligning of panels.
TIP

B. Double-Width Shelf
Place double-width shelf on brackets.
A. Rubber Pads
Place rubber pad on top of center post.
A
BA. Insert Side Panels
Carefully slide side panels down
outside posts. Be sure the posts are
square to the bottom shelf to prevent
any damage to side panels.
Doc No. 500-615/v8.12 229 -3/4
4Placing Shelves
B. Secure Top
Secure top with the 5 connector bolts.
Place the plastic plugs in the front center hole.
5Sides and Top Assembly

A.Attach Hinges to Door Frames
Insert the hinges into the corresponding holes
on the doors. Turn the screws 1/4 turn to the
right to lock hinges in place. NOTE: Do not over
tighten or the hinge will break.
D.Door Pull
Screw the Door Pull into place.
Doors should be 1/8” above the bottom shelf before fully
tightening hinges to post. Use the wrench thickness as a guide
for the bottom gap. Secure hinges in place with hex key.
Attach the rubber stops to the
inside of the door frame where
it hits the shelf pegs.
Attach Doors
Note: The hinge can be separated by pulling the
black tab and pulling apart the hinge from the hinge
base. Separated hinges snap back together.
LIFT UP
SHELF
PEG
6
Doc No. 500-615/v8.12 229 -4/4
B.Adjust Clearance C.Rubber Stops
A
B
SOFT
CLOSE
INSTALLATION
SLOW CLOSE
FAST CLOSE