Salamander SYNERGY 303 User manual

BEFORE YOU BEGIN:
• Unpack all parts before beginning and refer to the drawing below.
• Shelf pegs and door hinges must slide into the channels of the post in the correct order.
They cannot be removed individually without disassembling the whole unit.
AB
SYNERGY 303
Instructions
Includes:
(1) SU30 - Synergy Base Unit
(1) SS30 - 30” Side Panel Set
(1) SD30 - 30” Doors
!
!
Limited Warranty
For five full years Salamander Designs Ltd. will repair or replace, at our option, any product defective in materials or craftsmanship. Salamander Designs Ltd. will not be responsible for any damage to or destruction of other equipment consequential
to our equipment failure. Defective product must be given Return Authorization and is to be returned to the factory prepaid, in the original carton and packing material. Any damage incurred in a shipment not in original packaging shall be the
responsibility of the owner. Warranty repairs will be returned prepaid, via UPS within the continental U.S.A. only. Salamander Designs Ltd. • 800-535-5659 • www.SalamanderDesigns.com
Doc No. 500-630/v6.18 ©2002 Salamander Designs Ltd.
1
B
B
A
A
Leveler Foot
Hex Nut
Washer
90
O
B.Connect Post
Screw foot with metal washer
through bottom shelf and
onto the end of an extruded
post. Hand tighten fully and
use wrench on hex nut to tighten
nut onto underside of shelf.
A.Square Post
Square the post to the bottom shelf.
Connect Posts to Bottom Shelf
WARNING: Tighten by screwing the leveler foot NOT the post.
2Add Shelf Pegs & Door Hinges
!
!
B.Insert Hinges, Shelf Pegs & Heavy Duty Bracket
Note: The door can be either left or right side opening. Select a side to open door.
1. Hold door above the post and slide the
bottom
hinge plate through the post channel.
2. Insert shelf pegs and heavy duty bracket.
3. Slide top hinge plate through.
4. Gently tighten all remaining pegs with the
hex key to desired position.
A.Group Shelf Pegs
There are two varieties of shelf pegs (A and B).
They are designed to cradle the shelf in place.
Refer to drawing.
Top Shelf (1)
Adjustable Shelf (3)
Bottom Shelf (1)
Joint Connector Bolt 300-540 (4)
Foot & Nut P-300-350 (4)
Door (1)
Aluminum Post (4)
Sides (2)
Washer 300-470 (4)
Shelf Peg
PHK-370 Right (4)
PHK-380 Left (4)
Heavy Duty Bracket (2)
Rubber Tabs

A.Insert Hardware
Combine the 1” threaded studs with the flat
nuts. Slide hardware into rear channel.
A.Attach Hinges to Door Frames
Insert the hinges into the corresponding holes on
the doors. Turn the screws 1/4 turn to the right to
lock hinges in place.NOTE: Do not over tighten
or the hinge will break.
D.Door Pull
Screw the Door Pull into place.
B.Adjust Clearance
Doors should be 1/8” above the bottom shelf before
fully tightening hinges to post. Use the wrench thickness
as a guide for the bottom gap.
C.Rubber Stops Attach
the rubber stops to the inside of the door frame where it
hits the shelf pegs when closing the door.
C.Secure Studs
Use the hex key to secure the all
studs to the posts.
B.Place Panel
Allow bottom studs to remain
loose at bottom of post. Align the
Spacer Tool at the top of the post,
then position top studs through the
small “Rear Panel” hole. Repeat this
step with the bottom studs aligning
the Tool along the bottom of post to
set spacing for cable passage.
1 2 3 4 5 6 7 8 9 
S20 / SVDO
REAR PANEL
4
1/2
"
6"
8"
www.salamanderdesigns.com
EXTENDED
REAR PANEL
S 30 / S40
REAR PANEL
SPACER
TOOL
1 2 3 4 5 6 7 8 9 
S20 / SVDO
REAR PANEL
4
1/2
"
6"
8"
www.salamanderdesigns.com
EXTENDED
REAR PANEL
S 30 / S40
REAR PANEL
SPACER
TOOL
2X
2X
REAR
Attach Rear Panel
Attach Door
C. Insert Side Panels
Carefully slide side panels down center
channel of outside post. Be sure the
posts are square to the bottom shelf to
prevent any damage to side panels.
D. Secure Rear & Top
Put the remaining thumb nuts on
to complete panel installation.
B. Fine Tuning
Use the bubble level to precisely adjust
the shelves. Be sure to level both sides
as well as front to back. Use the hex key
to tighten each peg.
A. Placing & Adjusting Shelves
Place shelves from the bottom up. Angle the
shelf in between the front post and set on top of
shelf pegs. Use the Spacer Tool to adjust spac-
ing between shelves. Position the peg through
the Spacer and tighten.
5Final Assembly
4
Note: The hinge can be separated by pulling the
black tab and pulling apart the hinge from the
hinge base. Separated hinges snap back together.
PULL
3
Rubber Tabs