Salamander SYNERGY 245 User manual

BEFORE YOU BEGIN:
• Unpack all parts before beginning and refer to the drawing below.
• Shelf pegs and door hinges must slide into the channels of the post in the correct order.
They cannot be removed individually without disassembling the whole unit.
SYNERGY 245
Quad Assembly
Includes:
(1) Quad 20 Baseunit
(4) Side Panels
(4) Rear Panels
(2) S20 Doors
(2) S10 Doors
(2) Adjustable Shelves
(1) Double Width Shelf
!
!
Salamander Designs Ltd. 800-535-5659 • www.SalamanderDesigns.com ©2005 Salamander Designs Ltd. ® Synergy System, Patented.
Limited Warranty
For five full years Salamander Designs Ltd will repair or replace, at our option, any product defective in materials or craftsmanship. Salamander Designs Ltd. will not be responsible for any damage to or
destruction of other equipment consequential to our equipment failure. Defective product must be given Return Authorization and is to be returned to the factory prepaid, in the original carton and packing
material. Any damage incurred in a shipment not in original packaging shall be the responsibility of the owner. Warranty repairs will be returned prepaid, via UPS within the continental U.S.A. only.
Doc No. 501-090/v6.18 245 - 1 of 4

1
B
B
A
A
Leveler Foot
Hex Nut
Washer
90
O
B.Connect Post
Screw foot with metal washer through bottom
shelf and onto the end of each extruded post.
Place the 8.5” Post front and center of unit.
Hand tighten fully and use wrench to tighten
nut onto underside of shelf.
C.Post Cover
Press post cover onto 8.5” center
post to protect the center shelf.
A.
Square Post
Square the post to the bottom shelf.
Connect Posts to Bottom Shelf
WARNING: Tighten by screwing the leveler foot NOT the post.
2Add Shelf Pegs & Door Hinges
!
!
B.Heavy Duty Bracket
The heavy duty brackets will be used
to supoort the double-width shelf.
C.Door Hinges & Shelf Pegs
1. Slide the bottom hinge plate through the
front post channels. (Doors can be either left
or right side opening.)
2. Insert one shelf peg into each post
except the center posts.
3. Slide top hinge plate through front
post channels.
A.Group Shelf Pegs
There are two varieties of shelf pegs (A and B).
They are designed to cradle the shelf in place.
Refer to drawing. A B
Doc No. 501-090/v6.18 245 -2 of 4

A.Attach Hinges to Door Frames
Insert the hinges into the corresponding holes on
the doors. Turn the screws 1/4 turn to the right to
lock hinges in place. NOTE: Do not over tighten
or the hinge will break.
D.Door Pull
Screw the Door Pull into place.
B.Adjust Clearance
Doors should be 1/8” above the bottom shelf before
fully tightening hinges to post. Use the wrench thickness
as a guide for the bottom gap. Secure hinges in place
with hex key.
C.Rubber Stops
Attach the rubber stops to the inside of the door
frame where it hits the shelf pegs.
Attach Doors
Note: The hinge can be separated by pulling the
black tab and pulling apart the hinge from the
hinge base. Separated hinges snap back together.
PULL
SHELF
PEG
3
Doc No. 501-090/v6.18 245 -3 of 4

A.
Insert Hardware
Combine the 1” threaded studs with the flat nuts.
Slide 2 sets of hardware down the two outside
posts and 4 sets down the three center posts.
Allow studs to remain loose at bottom of post.
B.Position & Secure Studs
Align the Spacer Tool at the top of each post, then
position top studs through the small “Rear Panel”
hole. Repeat this step with the bottom studs
aligning the Tool along the bottom of post to
set spacing for cable passage. Use the hex key
to secure the top and bottom studs to the posts.
C.Place Rear Panels
Secure each panel in place with thumb nuts.
2X 4X 4X 2X
4X
REAR
Attach Rear Panels
A. Placing & Adjusting Shelves
Place shelves from the bottom up. Angle the
shelf in between the front post and set on top
of shelf pegs. Use the Spacer Tool to adjust
spacing between shelves. Position the peg
through the Spacer and tighten.
5Final Assembly
4
Doc No. 501-090/v6.18 245 -4 of 4
C. Insert Side Panels
Carefully slide side panels down center
channel of outside posts. Be sure the
posts are square to the bottom shelf to
prevent any damage to side panels.
B. Fine Tuning
Use the bubble level to precisely adjust
the shelves. Be sure to level both sides
as well as front to back. Use the hex
key to tighten each peg.
D. Secure Top
Secure top with the 8 connector bolts to
complete installation.