Salus RT310RF User manual

Installation Manual
Model: RT310RF

Product Compliance .................................................................................................. 3
Safety Information ....................................................................................................... 3
Box Content .................................................................................................................... 3
Introduction ................................................................................................................... 4
Features ............................................................................................................................. 5
Installation ....................................................................................................................... 5
Button functions and keys .................................................................................... 7
Installer mode ............................................................................................................... 9
Operations ...................................................................................................................... 10
Other functions ............................................................................................................12
Factory reset ...................................................................................................................13
Technical info ................................................................................................................ 13
Warranty ........................................................................................................................... 14
02 RT310RF Installation Manual
Contents

Product Compliance
Safety Information
This product complies with the essential requirements and other relevant provisions of the following
EU Directives: 2014/30/EU, 2014/35/EU, 2014/53/EU and 2011/65/EU. The full text of the EU Declaration of
Conformity is available at the following internet address: www.saluslegal.com.
Use in accordance with the EU and national regulations. For indoor use only. Keep your device completely dry.
Thisproduct mustbeinstalled bya competentpersonand inaccordancewithall theEU andnational regulations.
Always isolate the AC Mains supply before installing or working on any components that
require 230 VAC 50Hz supply.
Box content
The box includes the 310RF thermostat, the RT310 receiver (pre paired), 2 AA batteries a set of screws and the
Quick Guide installation manual.
RT310RF thermostat RXRT510 receiver
2xAA batteries and 4x screws Installation Quick Guide
RT310RF Installation Manual 03

Introduction
A room thermostat simply switches the heating system on and off as necessary. It works by sensing the air
temperature, switching on the heating when the air temperature falls below the thermostat setting, and
switching it off once this set temperature has been reached.
Turning a room thermostat to a higher setting will not make the room heat up any faster. How quickly the room
heats up depends on the design of the heating system, for example, the size of boiler and radiators. Neither
does the setting affect how quickly the room cools down. Turning a room thermostat to a lower setting will
result in the room being controlled at a lower temperature, and saves energy.
The heating system will not work if a time switch or programmer has switched it off.
The way to set and use your room thermostat is to find the lowest temperature setting that you are comfortable
with, and then leave it alone to do its job. The best way to do this is to set the room thermostat to a low
temperature – say 18⁰C – and then turn it up by one degree each day until you are comfortable with the
temperature.
You won’t have to adjust the thermostat further. Any adjustment above this setting will waste energy and cost
you more money.
If your heating system is a boiler with radiators, there will usually be only one room thermostat to control the
whole house. But you can have different temperatures in individual rooms by installing thermostatic radiator
valves (TRVs) on individual radiators. If you don’t have TRVs, you should choose a temperature that is reasonable
for the whole house. If you do have TRVs, you can choose a slightly higher setting to make sure that even the
coldest room is comfortable, then prevent any overheating in other rooms by adjusting the TRVs.
Room thermostats need a free flow of air to sense the temperature, so they must not be covered by curtains
or blocked by furniture. Nearby electric fires, televisions, wall or table lamps may prevent the thermostat from
working properly.
04 RT310RF Installation Manual

The RT310RF from SALUS Controls is a stylish and
accurate digital thermostat with an easy to read Liquid
Crystal Display (LCD).
The Receiver is used for wiring connections and heat on/
off control. The thermostat provides the user interface
and temperature sensing / control. The two units are
linked together by a Radio Frequency (RF) signal.
Features
Frost protection
Low-Battery Warning
Low-Battery Detection
Modern Casing
Sleep Mode
User Friendly
Pre-Paired in Factory
RF Test Pairing
Features
Installation
The DIP switches are found on the rear of your thermostat and can be used to change the span (temperature
accuracy) of your thermostat from the default +/-0.5°C to +/-0.25°C. This may cause your boiler to operate
more frequently. The DIP switches are located on the back of the thermostat. ON +/-0.25°C, OFF +/-0.5°C.
The span is the accuracy with which the thermostat operates when displaying your temperature. You can
increase the accuracy by setting the span to +/-0.25°C, meaning that your thermostat will be sensitive to a
quarter of a degree temperature change and will activate/deactivate the boiler.
DIP switch settings
+/-0.25
+/-0.5
ON
2
Note: Please insert batteries into the RT310RF thermostat and it will power up..
RT310RF Installation Manual 05

Connecting the RXRT510 receiver
ON
AUTO
OFF
MANUAL
Wall mounting
COMNO L N
Terminal Description Receiver Terminals
NO
COM
L
N
Switch Terminal
Common Switch
Terminal
Mains Live (230VAC)
Mains Neutral
Wiring
Fit the front housing.
Press lightly
Fix the backplate to the wall Align the front housing
at the top edge.
NO COM L N
L N
Electrical diagram
COMNO L N
Unscrew the backplate of the RXRT510 receiver in order to do the wiring connections. After that please switch
the receiver ON.
06 RT310RF Installation Manual

Button functions and keys
Key Function
Turn on the LCD backlight
Turn On/Off the Frost Mode
Increase button
Decrease button
1. Press once to enter/exit in RF Test Mode
2. Press for 3 seconds to enter/exit Pairing Mode
Press for 3 seconds all the buttons to enter Installer
Mode
+
+
ON
AUTO
OFF
MANUAL
Key/LED Function
AUTO System receiver output will switch on and off
in relation to the command from the RT310RF
transmitter.
Manual System receiver output is controlled by the On/Off
slide switch.
ON When in Manual Mode, ON will turn on the boiler.
OFF When in Manual Mode, OFF will turn off the boiler.
Red Led Receiver On, paired.
Green Led Command from thermostat received.
There are few user controls for the RT310RF, making this thermostat very easy to operate. These controls are
shown below, along with a description of each of their functions. The temperature displayed on the LCD is the
current room temperature. All teh LCD icons with a description are shown below.
Thermostat
Receiver
Thermostat LCD Icon Meaning
Thermostat is calling for heat
Thermostat is in Frost Protection Mode
Thermostat is paired with the receiver
Low Battery Warning Indicator
Current Temperature/Set Point Temperature
TESTING/PAIRING
RT310RF Installation Manual 07

Test Pairing Function
Make sure your devices are wired and the thermostat has batteries inserted. Switch receiver to ON. If you are
using the RT310RF pack, the pairing between the thermostat and the receiver is already done. If you bought
the RT310TX and RXRT510 separately then pair as follows. Please make sure that the Receiver is set on Auto.
ON
AUTO
OFF
MANUAL
ON
AUTO
OFF
MANUAL
TESTING/PAIRING TESTING/PAIRING
Test the pairing process
TESTING/PAIRING
TESTING/PAIRING TESTING/PAIRING
3 Sec Wait 9 minutes for the timeout
process to be complete.
Begin the pairing process End the pairing process
TESTING/PAIRING
3 Sec
Testing the RF transmissions
It is important to site both the Receiver and thermostat in locations where the RF signal cannot be interrupted.
The receiving range between the thermostat and Receiver is approximately 30 metres indoors, however many factors can
affect the RF transmission and shorten the operating distance, e.g. shielding by thick walls, foil back plasterboard, metal
objects such as filing cabinets, general RF interference, and so on. The range is generally large enough for most household
applications, but it is advisable to test the RF transmission from the intended thermostat location to the Receiver location
before fixing the thermostat to the wall.
To check the RF reception, follow the following steps:
1. Press the UP button on the thermostat until the set point temperature is higher than room temperature by a few
degrees.
2. Wait for a few seconds. The Heat on (heat call) indicator should appear on the bottom left of the LCD on the thermostat.
3. Check the green LED on the receiver unit - it should be lit.
4. Press the DOWN button to adjust the set point temperature to be lower than room temperature.
5. Wait for a few seconds, and the Heat on (heat call) indicator should disappear and the green LED should switch off.
6. If at step 3 the green LED is not illuminated, press the TEST/PAIRING button on the thermostat and try to place the
thermostat closer to the Receiver.
7. Repeat steps 1 to 5.
Note: Before beginning the process, switch the receiver On/Off and then On again to reset it (On/Off/On).
ON
AUTO
OFF
MANUAL
ON
AUTO
OFF
MANUAL
ON
AUTO
OFF
MANUAL
08 RT310RF Installation Manual

Installer Mode
Press and hold and and keys to enter installation setting.
The first setting is temperature display resolution selection - d01. Press to enter the existing setting.
The setting will start flashing. Press or to change temperature display resolution, wait for 10 seconds
to confirm, then enter d02 (if you didn’t press to save your selection, the change will be confirmed after 10
seconds and the thermostat will return to normal mode). d02 is to set temperature offset, press or to
increase/decrease offset. To exit Installer Mode don’t press any key for 10 seconds, or press
See the table below.
dxx Function Parameter Description Default
value
d01 Temperature display
increments
0.1°C or
0.5°C
Select the temperature display
increments
0.5°C
d02 Temperature offset +/-3.0°C Calibrate your thermostat tempera-
ture
0.0°C
d03 Frost setpoint 5.0°C-17.0°C Set the Frost Point temperature 5.0°C
RESET
Press the three buttons
together for 3 seconds.
3 Sec 3 Sec
3 Sec
RESET
Enter first d01 setting. Press
5
Select increment. Press
TESTING/PAIRING
Continue adjusting the d02 and d03 following the same steps as above.
Once you have finished setting up all the parameters, press to exit
to home screen, or don’t press any button for 10 seconds and it will
exit automatically.
2
TESTING/PAIRING
RT310RF Installation Manual 09

Operations
Initial Power UP
After power up, the thermostat is reset. During system reset, all LCD icons are displayed for 2 seconds and
the keys are locked. After that, all keys are unlocked and the thermostat is initialized. Then software version is
shown.The typical reset display is shown below.
The following table shows the settings of the RT310RF digital thermostat after Power on, or after TEST/PAIRING
button is pressed:
Function Status after Reset
Operation Mode Normal mode
Room Temperature 22.0°C, to be renewed within 5 seconds
Setpoint Temperature 20.0°C
°C indicator On
Frost Protection indicator Off
Heat indicator Off
Low-Battery Warning indicator Off, to be renewed within 5 seconds
Output Relay Off
Reviewing Setpoint Temperature
Press or to review Setpoint temperature. The flame icon won’t be turned on.
When operating in Frost protection mode, the LCD will show frost setpoint with the Frost Protection
indicator displayed.
Press Backlight or wait 2 seconds without key press to return to normal operation, room temperature will
be displayed.
Actual room temperature Setpoint temperature
TESTING/PAIRING TESTING/PAIRING
10 RT310RF Installation Manual