Samsung NX-828 User manual

SAMSUNG
NX-828
KEYSET USER
GUIDE
coverA5 99.3.17 4:8 PM ∆‰¿Ã¡ˆ13

NX-24E / NX-24B
NX-6B
NX-AOM
KEYSET USER GUIDE
SAMSUNG
HYBRID KEY SYSTEM
NOVEMBER 1998
coverA5 99.3.17 4:8 PM ∆‰¿Ã¡ˆ15

SAMSUNG TELECOMS
Publication Information
Samsung Telecoms reserves the right without prior notice to
revise information in this publication for any reason.
Samsung Telecoms also reserves the right without prior notice
to make changes in design or components of equipment as
engineering and manufacturing may warrant.
Copyright 1998
Samsung Telecoms
All rights reserved. No part of this manual may be reproduced in
any form or by any means - graphic, electronic or mechanical,
including recording, taping, photocopy or information retrieval
system - without express written permission of the publisher of
this material.
NOVEMBER/1998
coverA5 99.3.17 4:8 PM ∆‰¿Ã¡ˆ16

ToSelectASpecificOutsideLine
1. Check the line status indicator light, and press
an idle outside line button.
¡¤ You will receive dial tone through the
speaker. Or,
lift the handset and dial the outside line
access number.
2. Dial the outside telephone number.
ToSelectAnyFree OutsideLineFrom
AnOutgoingGroup
1. Lift the handset, and listen for adial tone.
2. Dial the outgoing group number.
¡¤Afree line in the group will be selected and
you will hear adial tone.
¡¤If all lines in the group are busy,
¡¸9ALL BUSY¡¹is displayed, and you will
receive abusy signal.
3. Dial the outside telephone number.
¡¤When making an outside call on adial pulse
line, all digits entered after pressing [#]will
be sent as tones.
¡¤When dialing an outside call, press [PSE]button
to insert athree second pause. [PSE]button is
set by system programming.
OUTSIDE CALLS
2
Making anOutsideCall
3NOTE
/
/

1. Lift the handset.
Or,
press [SPEAKER]to converse using the
speakerphone.
¡¤ To answer acall while you are on the phone,
press the ringing line button. The current line is
automatically held, and you can talk with the
new caller.
¡¤ You may answer calls ringing at another station
by pressing the fast blinking outside line button.
Or, lift the handset and press [1][0]and the
outside line number. You will be connected to
the outside line.
3
OUTSIDE CALLS
Answering anoutsideCall
3NOTE

1. Lift the handset, and dial the desired station
number.
Or, press the desired station's [DSS]button, with
the handset on-hook.
¡¤The speakerphone activates automatically
and your phone starts dialing.
¡¤To program astation number into the [DSS]
button, refer to the TechnicalManual.
2. When the other party answers, either speak
into the handset or talk using speakerphone.
3. To end the call, replace the handset or press
[SPEAKER], if using the speakerphone.
To answer aringing line, or place acall to
another intercom station, while talking with one
intercom station, press the [DSS]button for the
second station without hanging up. The original
station line is automatically disconnected and the
second station will ring. This feature is not available
on standard phones.
Lift the handset or press [SPEAKER].
Dial [0]to call your system operator group.
You can call the operator group by dialing the
Operator group number. The Operator group is the
station group numbered 500.
INTERCOM CALLING
4
CallingOtherStations
CallingtheOperator
Group
3NOTE
3NOTE

Lift the handset or press [SPEAKER],and dial the
station group number.
Or, press the [SGR]button of the desired station
group.
You can set your phone to Auto-Answer or
Voice-Announce mode.
ToSetAuto-Answer Mode
1. With the handset on-hook, press [AUTORDL]
and dial [1][0]to enter program mode.
2. Press [2]to set Auto-Answer Mode.
3. Press [AUTORDL]to save and exit.
ToSetVoice-Announce Mode
1. With the handset on-hook, press [AUTORDL]
and dial [1][0]to enter program mode.
2. Press [3]to set Voice-Announce Mode.
3. Press [AUTORDL]to save and exit.
Auto-Answer mode can be changed by acaller by
pressing [TRANSFER]and dialing [1][4].
Or, pressing the [FAT]button.
On asingle-line telephone, hook flash and dial
[1][4].
5
INTERCOM CALLING
StationGroupCalls
AnswerModeChange
/
/
3NOTE

When connected to an outside line, use this
feature to allow you to hang up the line
temporarily without disconnecting. While on hold,
the held party will hear music. Another station
may retrieve the outside line on hold.
1. When connected to an outside line press
[HOLD].
¡¤The outside line is placed on hold, and
the HOLD indicator blinks slowly.
2. After placing acall on hold, you can make
or answer another call.
3. To retrieve the held outside line, press the
blinking line button.
If the held line is not released within a
predetermined time, the system rings you back so
that you do not forget about the call. If you do
not answer the call, it is automatically recalled to
the operator group. (Operator group is the station
group numbered 500)
To place acall on hold at your phone and not
allow other user to take it, use Exclusive hold.
ToPlace anOutsideCall onExclusiveHold
1. When connected to an outside line, press
[HOLD]twice.
6
CALL PROCESSING
SystemHold
ExclusiveHold
3NOTE
/

¡¤The outside line placed on hold will flash
green at your keyset, and show asteady
red light on all other keysets.
2. After placing acall on hold, you can answer
or make another call.
3. To retrieve the held outside line, press the
blinking line button.
¡¤You must press [HOLD]the second time within 2
seconds after pressing the first [HOLD]in Step 1.
¡¤If aheld line is not released within a
predetermined time, the system rings you back,
so that you do not forget about the call. If you
do not answer the call, it is automatically
recalled to the operator group. (Operator group is
station group numbered 500)
ToPlace anIntercomCall on
Exclusivehold
1. When connected to any station, press [HOLD]
once.
¡¤The station's [DSS]button will blink at your
keyset, and show asteady red light on
other keysets.
2. After placing acall on hold, you can answer
or make another call.
3. To retrieve the held call, press the
blinking [DSS]button.
Intercom calls will always be placed on exclusive
hold.
CALL PROCESSING
7
3NOTE
/
3NOTE

This feature allows you to transfer acall to
another station or group. Any outside or intercom
call may be transferred, regardless of whether you
initiated or received the call.
When you transfer acall, you may wait on the
line and announce the call, or you may hang up
when you hear the ringback tone.
The connection between the caller and the
person to whom the call is being transferred is
completed when you hang up.
Keyphone
1. With an outside call in progress, press the [DSS]
button for the other station to which you want
to transfer the call.
¡¤You hear atransfer tone and the other
party hears music.
Or, with an intercom or outside call in
progress, press [TRANSFER],and dial the
station or group number.
¡¤If you want to transfer the call to the
operator group, dial [0].
2. Replace the handset.
Or, wait on the line and announce the call,
then replace the handset.
¡¤If the transferred station is busy, press
[TRANSFER]again. You will be
reconnected to the original call.
8
CALL PROCESSING
TransferringCalls