Samsung OFFICESERV 7100 User manual

OfficeServ 7100 INSTALLATION
TECHNICAL MANUAL PART 1 MAY 2010
TABLE OF CONTENTS
INSTALLATION SECTION
PART DESCRIPTION PAGE
1 PRE-INSTALLATION INFORMATION
1.1 SITE REQUIREMENTS............................................................................................1.1
1.2 GROUNDING CONDITIONS................................................................................1.2
1.3 POWER CONDITIONS...........................................................................................1.4
1.4 UNPACKING AND INSPECTION.........................................................................1.4
2 INSTALLING CABINETS
2.1 SYSTEM INSTALLATION PROCEDURE.............................................................2.1
2.2 SELECTING INSTALLATION METHOD .............................................................2.1
2.3 INSTALLING IN A RACK........................................................................................2.1
2.4 INSTALLING ON A WALL USING
THE TWO PIECE BRACKET KIT............................................................................2.4
2.5 INSTALLING ON A WALL USING
THE BRACKET KIT ..................................................................................................2.8
2.6 CONNECTING GROUND WIRES...................................................................... 2.12
3 INSTALLING AND REPLACING BOARDS
3.1 CABINET CONFIGURATION ................................................................................3.1
3.2 MP10/MP10a PROCESSOR CARD.....................................................................3.2
3.3 INTERFACE CARDS............................................................................................. 3.12
3.4 DAUGHTERCARD MODULES .......................................................................... 3.15
3.5 OTHER INTERFACE CARDS .............................................................................. 3.22
3.6 CONNECTING POWER FAIL TRANSFER ....................................................... 3.37
4 CONNECTING EXTERNAL BATTERIES
4.1 CONNECTING EXTERNAL BATTERIES..............................................................4.1
5 CONNECTING POWER
5.1 BEFORE CONNECTING POWER .........................................................................5.1
5.2 PROCEDURE FOR CONNECTING POWER.......................................................5.1
Home Page
Table of Contents
Home Page
Table of Contents

OfficeServ 7100 INSTALLATION
TECHNICAL MANUAL PART 1 MAY 2010
6 CONNECTING C.O. LINES
6.1 SAFETY PRECAUTIONS ........................................................................................6.1
6.2 CONNECTING C.O. LINES ....................................................................................6.2
7 CONNECTING STATIONS AND ADDITIONAL EQUIPMENT
7.1 CONNECTING STATIONS ....................................................................................7.1
7.2 CONNECTING ADDITIONAL EQUIPMENT................................................... 7.23
8 POWER UP PROCEDURES
8.1 PRE-CHECK ..............................................................................................................8.1
8.2a STARTING THE SYSTEM (MP10)........................................................................8.1
8.2b STARTING THE SYSTEM (MP10a)......................................................................8.2
8.2c UPGRADING MP10 with MP10a CARDS ........................................................8.3
8.3 PRECONFIGURED NUMBERING EXTENSIONS
AND C.O. LINES......................................................................................................8.3
9 SOFTWARE AND DATABASE MANAGEMENT
9.1a SOFTWARE MANAGEMENT WITH MP10 INSTALLED.................................9.1
9.1b SOFTWARE MANAGEMENT WITH MP10a INSTALLED ..............................9.1
9.2 DATABASE MANAGEMENT ................................................................................9.2
10 ADDING CARDS TO THE SYSTEM
10.1 ADDING STATIONS AND TRUNKS................................................................. 10.1
FIGURES
Figure 2.1 Tools Required for Rack Installation
Figure 2.2 Rack Installation (1)
Figure 2.3 Rack Installation (2)
Figure 2.4 Rack Installation (3)
Figure 2.5 Required Tools for Wall Mounting
Figure 2.6 7100 Cabinet Side View--Bracket Angle Out
Figure 2.7 7100 Cabinet with Brackets
Figure 2.8 Mounting the 7100 Cabinet on the Wall
Figure 2.9 Making Holes for Top and Bottom Brackets
Figure 2.10 Hammering Plastic Anchors
Figure 2.11 Side View Wall Mounted 7100 Cabinet
Figure 2.12 Required Tools for the Installation on a Wall
Figure 2.13 Installation on a Wall (1)
Home Page
Table of Contents
Home Page
Table of Contents

OfficeServ 7100 INSTALLATION
TECHNICAL MANUAL PART 1 MAY 2010
Figure 2.14 Installation on a Wall (2)
Figure 2.15 Installation on a Wall (3)
Figure 2.16 Installation on a Wall (4)
Figure 2.17 Installation on a Wall (5)
Figure 2.18 Installation on a Wall (6)
Figure 2.19 Installation on a Wall (7)
Figure 2.20 Grounding
Figure 3.1 Front/Rear View of OfficeServ 7100 Cabinet
Figure 3.2a Switch Setting (MP10)
Figure 3.2.b Switch Setting (MP10a)
Figure 3.3 Mounting a Modem Card on the MP10/MP10a
Figure 3.4 Mounting a 4SWM or 4DLM on the MP10/MP10a Card
Figure 3.4a Real Time Clock Battery (RTC)
Figure 3.5 Mounting the MP10/MP10a into Slot 0
Figure 3.6 Secure the MP10/MP10a into Slot 0
Figure 3.7a Front View of the MP10
Figure 3.7b Front View of the MP10a
Figure 3.8 Installing Interface Cards
Figure 3.9 Inserting Interface Card into Slots 1 and 2
Figure 3.10 Turning the Cabinet Power Off
Figure 3.11 Removing a Card
Figure 3.12 Replacing a Card
Figure 3.13 Installing the UNI Card
Figure 3.14 Front View of UNI Card
Figure 3.15 4SWM
Figure 3.16 Modem Card
Figure 3.17 4TRM
Figure 3.18 4DLM
Figure 3.19 4SLM
Figure 3.20 Setting Switches on the TEPRI/TEPRIa
Figure 3.21 Front View of the TEPRI/TEPRIa
Figure 3.22 Front View of the 8TRK
Figure 3.23 Front View of the 8TRK2
Figure 3.24 Front View of the 16TRK
Figure 3.25 Front View of the 16DLI2
Figure 3.26 Front View of the 8DLI
Figure 3.27 Front View of the 8COMBO
Figure 3.28 Front View of the 8COMBO2
Home Page
Table of Contents
Home Page
Table of Contents

OfficeServ 7100 INSTALLATION
TECHNICAL MANUAL PART 1 MAY 2010
Figure 3.29 Front View of the 16MWSLI
Figure 3.30 Front View of the 8SLI
Figure 3.31 Front View of the 8SLI2
Figure 3.32 Front View of the MGI16
Figure 3.33 Front View of the OAS Card
Figure 3.34 Example of Power Fail Transfer Connection to 8SLI
Figure 4.1 Connecting an External Battery
Figure 5.1 Connecting Power
Figure 6.1 Tip and Ring Connections to Trunk Cards
Figure 6.2 RJ-45 Port of TEPRI/TEPRIa
Figure 7.1 RJ-45 Port of the 8SLI
Figure 7.2 RJ-45 Port of the 16MWSLI
Figure 7.3 RJ-45 Port of the 8COMBO/8COMBO2 (For Analog Phone)
Figure 7.4 RJ-45 4SLM Port on the UNI Card
Figure 7.5 RJ-45 4DLM Port on the UNI Card
Figure 7.6 RJ-45 Port of the 8DLI (For Digital Phone)
Figure 7.7 RJ-45 Port of the 16DLI2 (For Digital Phone)
Figure 7.8 RJ-45 Port of 8COMBO/8COMBO2 (For Digital Phone)
Figure 7.9 LAN Connections
Figure 7.10 Connecting a Door Phone and a Door Lock
Figure 7.11 Adding an iDCS KDBF Keyset Daughtercard Module
Figure 7.12 Wall-Mounting an iDCS Keyset
Figure 7.13 Wall-Mounting DS 5000, ITP-5121D and ITP-5107S Keysets
Figure 7.14 Attaching iDCS 64 Button Module to an iDCS Keyset
Figure 7.15 Attaching iDCS 14 Button Module to an iDCS Keyset
Figure 7.16 Attaching DS 64 Button Modules to a DS5021D or a DS5014D Keyset
Figure 7.17 Attaching SMT-i5264 AOM to Phone
Figure 7.18 Setting-Up SMT-i5264 AOM
Figure 7.19 IP AOM Network Configuration
Figure 7.20 Connecting Access Point to Ethernet Port
Figure 7.21 Connecting MOH/BGM Sources
Figure 7.22 Connecting External/Additional Page Equipment
Figure 7.23 Connecting Common Bells
Figure 7.24 OIT Connection to LAN Port
Figure 7.25 OIT and LAN Connection
Figure 7.26 OIT and Modem Connection
Figure 7.27 Connecting SMDR
Figure 7.28 Connecting to Printer
Home Page
Table of Contents
Home Page
Table of Contents

OfficeServ 7100 INSTALLATION
TECHNICAL MANUAL PART 1 MAY 2010
Figure 8.1 iDCS 28 Button Line Key Default
Figure 8.2 iDCS 18 Button Line Key Default
TABLES
Table 1.1 Power Specifications
Table 3.1 Card Installation Configuration
Table 3.2 Parts on the Rear Panel of the Cabinet
Table 3.3a Ports and LEDs of the MP10
Table 3.3b Ports and LEDs of the MP10a
Table 3.4 UNI Card Ports and LEDs
Table 3.5 Ports and LEDs of the TEPRI/TEPRIa
Table 3.6 Ports and LEDs of the 8TRK
Table 3.7 Ports and LEDs of the 16TRK
Table 3.8 Ports of the 16DLI2
Table 3.9 Ports and LEDs of the 8DLI
Table 3.10 16MWSLI Ports
Table 3.11 Ports and LEDs of the 8SLI/8SLI2
Table 3.12 MGI16 Front Panel Components
Table 3.13 OAS Front Panel Components
Table 6.1 OfficeServ 7100 Line Conditions
Table 7.1 Distance Between Stations and the System
Table 7.2 Specification for Wireless LAN Connection
Table 7.3 Installation Tool Specification
Home Page
Table of Contents
Home Page
Table of Contents