Sanyo DSR-M810P User manual

FILE NO.
REFERENCE No.SM5310588
L8HAE/XE
NOTE: 1. Parts order must contain model number part number and description
2. Substitute parts may be supplied as the service parts.
3. N.S.P. : Not available as service parts.
4. Regardless from the unit's specification the HDD may have a different capacity or there might be more than one
HDD installed.
Even with the same product number the HDD installed might have a different capacity or there might be either
one or two HDD installed.
Design and specifications are subject to change without notice.
SERVICE MANUAL
Digital Video Recorder
CON EN S
NOTES ON HANDLING INTERNAL HARD DISK DRIVE
COMPONENTS ........................................................................ 3
SPECIFICATIONS .................................................................... 4
1. DISASSEMBLY .................................................................... 5
2. RESETTING THE USE TIME ............................................... 6
3. ADJUSTMENT ...................................................................... 6
4. PARTS LIST.......................................................................... 9
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS...........C1
DSR-M810P
(Product Code : 175 811 28) (without HDD)
(Europe)
(U.K.)
(PAL General)
The components designated by a symbol ( ! ) in this schematic diagram designates components whose value are of
special significance to product safety. Should any component designated by a symbol need to be replaced use only the
part designated in the Parts List. Do not deviate from the resistance wattage and voltage ratings shown.
PRODUC SAFE Y NO ICE

− 2 −

− 3 −
1. Do not subject the unit to shocks or vibration.
If the unit is subjected to shocks or vibration, it may
damage the HDD or cause corruption of the data stored in
the HDD.
• Do not move the unit whi e the power is turned on.
A ways be sure to turn off the power before removing the
unit from or p acing it onto the rack.
• When transporting the unit, pack it secure y using the
specified packing materia s. In addition, use a method of
transportation that minimizes vibration.
• When p acing the unit down on a surface such as a f oor,
attach the specified feet to the base of the unit and p ace
it down gent y. If the feet are not attached, p ace the unit
down very carefu y so that it does not make any noise.
2. Do not move the unit for 30 seconds after turning
off the power.
After the power is turned off, the disk inside the HDD wi
continue to spin for a brief period due to inertia, and the
heads wi be in an unstab e state.
During this time, the unit is even more susceptib e to
shocks and vibration than when power is being supp ied.
Make sure that the unit is not subjected to even gent e
vibration for at east 30 seconds after turning off the
power.
3. Do not operate the unit when condensation has
formed.
If the unit is operated when condensation has formed, it
may cause operating prob ems.
If sudden changes in the ambient temperature occur, wait
for the temperature to stabi ize before operating the unit.
NOT S ON HANDLING INT RNAL HARD DISK DRIV COMPON NTS
This unit has a bui t-in hard disk drive (HDD).
Be sure to observe the fo owing points carefu y when operating, setting-up and servicing the unit.
4. Notes when replacing the HDD
Be sure to fo ow the correct rep acement procedure when
rep acing the HDD.
• HDDs that have been removed from their packaging may
not operate correct y if they are subjected to any shocks
or vibration. It is recommended that you p ace the HDD
onto a soft, eve surface with the printed circuit board
facing upward after unpacking it.
• Be carefu not to subject the HDD to shocks or vibration
when removing and tightening screws as part of the HDD
rep acement procedure. Make sure that a screws are
tightened secure y so that they wi not become oose.
• The HDD is sensitive to static e ectricity, so you shou d
take proper precautions to prevent static e ectricity
bui dup.
5. Handling the HDD unit by itself
If transporting or storing the HDD unit by itse f, a ways be
sure to pack it in the specified packaging first.
In addition, use a method of transportation that minimizes
vibration.
If the HDD becomes damaged, hand e the unit and the
damaged HDD that has been removed in order for it to be
rep aced carefu y to prevent the prob em from being
aggravated unti as the nature of the prob em can be
checked and ana yzed.

− 4 −
NTSC/PAL co or signa standard (Switchab e)
NTSC : 720 x 480 (Super/High), 352 x 480 (Standard)
PAL : 720 x 576 (Super/High), 352 x 576 (Standard)
MPEG2 (Video), MPEG1 Layer2 (Audio)
4 Leve s (Super+, Super, High, Standard)
Frame
1 (NTSC: 30 fps or PAL: 25 fps)
1
P ayback, Sti , Search, Cue, Review, Frame advance, S ow
Search by time and data
Search by a arm event ist
Eng ish/ French/ Spanish/ Deutsch
Month/ Day/ Year/ Hours/ Minutes/ Seconds
1.0 V p-p 75 Ω, unba anced, BNC
1.0 V p-p 75 Ω, unba anced, BNC
-8dBs, 27kΩ, unba anced, RCA pin jack
-8dBs, 600Ω, unba anced, RCA pin jack
-60dBs, 10kΩ, unba anced, 3.5mm mini jack
100BASE-TX/ 10BASE-T RJ-45
For compact f ash reader and CD-R/RW drive (Front)
3 termina s: A, B, C
Externa switch connection or VA-RMN01 remote contro
Norma open, Low eve active
Norma 5V, Low eve active
Norma open, Low eve active
Norma 5V, Low eve active
Norma open, Low eve active
Norma open. Low eve active
Norma 5V, Low eve active
Open co ector (500 mA), Low eve active
Open co ector (50 mA), Low eve active
120 V - 240 V AC, 50/ 60 Hz
440 mA
Temperature: 5 °C to 40 °C, Humidity:10% to 80 %
210 (W) x 96 (H) x 380 (D) mm
3.0 kg
SP CIFICATIONS
Te evision System :
Picture Reso ution :
Compression :
Picture Qua ity :
Recording Type :
Recording Speed :
Recording Area :
P ayback :
Search Mode :
•Time/ Data Search :
•A arm Search :
Menu Language :
C ock setting :
Video input termina :
Video output termina :
Audio input termina :
Audio output termina :
Microphone input termina :
LAN termina :
USB termina :
Contro connector (Push ock) :
•RS-485 termina :
•Remote contro input termina :
•C ock adjust input termina :
•C ock adjust output termina :
•Series REC input termina :
•Non REC output termina /
series REC output termina :
•A arm input termina :
•A arm reset input termina :
•A arm output termina :
•Warning output termina :
•Fu out warning termina :
Power :
Power consumption :
Operating environment :
Dimension :
Weight :

− 5 −
CP-1 PWB
TB-1 PWB
PW-1 PWB
HDD Unit
TP301
VR340
DM-1 PWB
OP-1 PWB
CN309
CABINET FRONT
CABINET BOTTOM
HOLDER HDD
COVER TOP
(So d separatey)
Stamp 2
Stamp 1
Stamp 3
Stamp 4
Fig. 1
1. DISASS MBLY
1-1. R MOVAL OF CABIN T, CIRCUIT BOARD LOCATIONS AND CP-1 BOARD LOCA-
TIONS OF ADJUSTM NT POINTS
NOTE:
1. P ease carry out the screw
stop of the attachment to HDD
in the order of the number
stamped on the HDD ho der.
2. P ease attach the 1st set of
an HDD unit in the front side
of a product.
3. Harness shou d use the
socket of an end.

− 6 −
3. ADJUSTM NT
1. AGC VOLTAG ADJUSTM NT
1. Terminate the VIDEO OUT termina with a 75 Ω registor.
2. Connect the co or bar generator to the VIDEO IN termina ,
and input co or bar signa (100 % white eve ).
2. Connect the osci oscope to the TP301.
3. Adjust VR340 so that the eve becomes 0.85 ± 0.03 Vp-p.
NOTE:
The adjustment va ue varies depending on whether the DM-
1 circuit board is present or not.
If the DM-1 circuit board is present, the adjustment va ue is
0.85 ± 0.03 Vp-p.
If the DM-1 circuit board is not present, the adjustment va ue
is 1.00 ± 0.03 Vp-p.
Measuring Point Measuring quipment Condition
Adj. Value
Osci oscope
Co or bar generator E-E Mode
Co or bar signa
(100% white eve)
0.85 ± 0.03 V p-p
TP301
(CP-1 board)
VR340 (CP-1 board)
Adj. Location
Fig. 3
0.85 ±
Vp-p
0.03
2. R S TTING TH US TIM
1.Press the V button for more than 3 seconds. DISK1 USE
time disp ay reverses.
2.USED TIME dispay to reset with the V button pressed.
3.Press the MENU RESET button. Time disp ay resets it.
4.When it is finished, the EXIT/OSD button is pressed.
< POWER FAILURE/USED TIME >
# 017 01-03 03:42 01-03 17:59
FA I LURE RECOVER
DISK1 USE : 00000H
DISK2 USE : - - - - -H
FIRMWARE : MAIN 1.01-00 / SUB 1.00-03

POWER : 00000H
01-03 03:33 01-03 03:34
01-02 05:43 01-03 03:32
01-01 16:06 01-01 20:59

ERROR RESET (ER81) : 0000

− 7 −
2.MAC ADDR SS
1. MAC address settings
Each device with LAN functions is contro ed with one bui t-in
48-bit address. Writing this address incorrecty may resu t in a
device ID error creating a ma function when using as part of a
network.
For this reason, each unit is contro ed by inputting a num-
bered address.
2. Preparations prior to writing the MAC address
1.RS-232C servicing too s (VHJ-0116)
2.PC (with a Windows 2000, XP OS, FD drive and RS-232
termina )
3.MAC address writing software (VJH-0165)
4.RS-232C cross cab e (VHJ-0149 or any commercia y
avai ab e item)
2-1. Insta ing the MAC address writing software
Copy the "MACW.EXE" fi e from the MAC address writing
software into the PC's optiona directory.
3.MAC address verification and writing procedures
1.Connect the RS-232C servicing too s (VHJ-0116) to the
CN309 socket ocated on the unit's CP1 board.
2.Connect the PC's RS-232C (COM1) termina to the RS-
232C servicing too s using the RS-232C cross cab e (VHJ-
0149 or any commercia y avai ab e item).
3.Turn the PC's power suppy ON and a MAC address writing
software directory wi appear.
4.Connect the unit to the monitor and turn the monitor's
power supp y ON.
5.Turn the unit's power suppy ON and press the RESET
button whi e pressing on the UP button. Lift your finger from
the RESET button but keep pressing the UP button.
6.Lift your finger from the UP button on y after hearing the
buzzer.
The SANYO ogo wi appear on the monitor's screen and
the present MAC address wi be disp ayed be ow the ogo.
7.C ick on "MACW.EXE" ocated in the PC's directory to
aunch the software.
8.When rep acing the repair board, input the "MAC Address
Code" attached to the repair board in "Mac Address".
For servicing other than board rep acement, verify whether
the "MAC Address Code" is identica to the code verified
prior to servicing. If the entry space is b ank or if the code is
wrong, input the "MAC Address Code" verified prior to
servicing.
9. C ick on the "WRITE" button.
"Write Finish" wi appear. C ick on "OK" when the MAC
address prior to the change appears on the monitor.
Be sure to check on the monitor that the MAC address has
changed.
10. C ick on "EXIT" to end operation.
WRITE
EXIT
Mac Address
Copyright by Sanyo E ectric Co., Ltd.
2003/ 9/ 4
08 00 7B 00 00 00
OK
Write Finish

− 8 −
3. OV RWRITING TH FIRMWAR
1. Prepare the CompactF ash card containing the firmware to
be overwrite and a USB connection-type CompactF ash
card reader.
2. Insert the CompactF ash card containing the firmware to be
overwrite into the card reader, and connect the card reader
to the unit's USB connector.
3. Turn on the power for the unit.
4. Press the MENU button to disp ay the "MAIN MENU"
screen.
5. Use the [ ] button or the [ ] button to move the cursor
to "7. POWER FAILURE/USED TIME" and then press the
CUE ([ ]) button to disp ay the "POWER FAILURE/USED
TIME" screen.
6. Press the [ ] button unti the cursor is disp ayed.
7. Press the [ ] button to move the cursor to the ine where
the version number appears, and then press the CUE
([ ]) button to disp ay the "FIRMWARE UPDATE" screen.
8. Use the [ ] button or the [ ] button to move the cursor
to "MAIN MICRO COMPUTER", "SUB MICRO COM-
PUTER" or "MAIN & SUB COMPUTER".
9. Press the CUE ([ ]) button to disp ay the confirmation
(YES/NO input) screen, and then use the [ ] button or
the [ ] button to se ect "YES".
< POWER FAILURE/USED TIME >
# 017 01-03 03:42 01-03 17:59
FA I LURE RECOVER
DISK1 USE : 00000H
DISK2 USE : - - - - -H
FIRMWARE : MAIN 1.01-00 / SUB 1.00-03

POWER : 00000H
01-03 03:33 01-03 03:34
01-02 05:43 01-03 03:32
01-01 16:06 01-01 20:59

ERROR RESET (ER81) : 0000
10. Press the CUE ([ ]) button.
• "WRITING NEW FIRMWARE!!", "DO NOT REMOVE
CARD!" AND "DO NOT POWER OFF!" wi be dis-
p ayed on the screen. Overwriting of the sub micropro-
cessor wi start and the front LED wi f ash. When
overwriting of the sub microprocessor is comp ete, the
LED wi stop f ashing , and then the process of
overwriting the main microprocessor wi start.
• "FIRMWARE UPDATE" wi be disp ayed and overwrit-
ing of the main microprocessor wi start.
• When overwriting of the main microprocessor is
comp ete, the unit wi automatica y reboot.
Note:
When the unit reboots, the messages "HARD DISK
CH CKING!!" and "DO NOT POW R OFF" will be dis-
played, and you must never turn the power off while they
are being displayed. If the power is turned off at this
time, the HDD may become damaged.
11. It ALL Format after a reboot by pushing simutaneous y
the front MENU RESET button and the RESET button on
the back.
< FIRMWARE UPDATE >
MOVE LINES WITH ↓↑ , SELECT WITH ←→
MAIN MICRO COMPUTER
MAIN & SUB COMPUTER
SUB MICRO COMPUTER
< FIRMWARE UPDATE >
DO YOU UPDATE FIRMWARE?
YES
CHANGE WITH ↓↑ , SET WITH →
MAIN & SUB COMPUTER
< FIRMWARE UPDATE >
DO NOT REMOVE CARD
DO NOT POWER OFF
WRITING NEW FIRMWARE
< FIRMWARE UPDATE >
DO NOT REMOVE CARD !
DO NOT POWER OFF !
SUB WRITING 14%
< FIRMWARE UPDATE >
DO NOT REMOVE CARD
DO NOT POWER OFF
UPDATE COMPLETED
< POWER FAILURE/USED TIME >
# 017 01-03 03:42 01-03 17:59
FA I LURE RECOVER
DISK1 USE : 00000H
DISK2 USE : - - - - -H
FIRMWARE : MAIN 1.01-00 / SUB 1.00-03
POWER : 00000H
01-03 03:33 01-03 03:34
01-02 05:43 01-03 03:32
01-01 16:06 01-01 20:59

ERROR RESET (ER81) : 0000

9
LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION
N.S.P.: Not available as service parts.
4. PARTS LIST
NJ503
NJ503
NJ503
NJ503
5020
5021
NJ503
N.S.P.:Not available as service parts.
NJ503
6035
HDD
NJ610
NJ612
6006
6007
6012
6011
NJ602
NJ602
CP-1 NJ603
NJ604 TB-1
6003
NJ608
NJ608
6004
7001
6005
6005
6005
NJ612
6001(N.S.P.)
5106
5103
5102
5108
5101 5104
5105
5107
NJ605
NJ605
NJ605
NJ605
6002(N.S.P.)
OP-1
NJ606
NJ609 NJ606
NJ607 NJ607
NJ609
NJ609
6030
W0001
NJ612
*CH-L8HAE/XE(MS)
5112
NJ611
NJ612
NJ610
NJ611
NJ613
NJ601
NJ602
PW-1
NJ616
6017
6013
NJ601
NJ601
NJ601
NJ601
6014
NJ614
6015
6015
NJ614
5051
DM-1
NJ602
6031
ACCESSORIES & PACKING MATERIALS
9110 613 203 4562 INSTRUCTION MANUAL
9111 613 203 6986 INSTRUCTION MANUAL,APPLICATION
9203 613 053 6495 FIXER
9210 412 062 6102 SPECIAL SCREW-3.5X4.5 ,HDD
9212 645 052 1997 CORE,FERRITE (LAN*POWER )
OR 645 060 3778 CORE,FERRITE (LAN*POWER )
9300 645 040 6072 CORD,POWER-1.8MK
9801 645 068 8676 DISC,CD-ROM PC-GUI
9001 613 203 6061 CARTON CASE
9002 613 200 3339 CUSHION
9003 613 200 7849 CUSHION,TOP
9004 613 200 8532 CUSHION,BACK
9005 613 200 3360 CUSHION,F/B, FRONT/BACK
9012 613 200 4879 BAG,INNER
CABINET & CHASSIS PARTS
5020 613 203 6085 COMPL,COVER TOP-L8HAE/XE
5021 613 200 0536 LABEL CAUTION HDD
5051 613 200 8167 DEC USB
5101 613 199 4812 CABINET FRONT
5102 613 199 4843 DEC FRONT
5103 613 199 4874 DEC INDICATOR
5104 613 199 4799 BUTTON 10P
5105 613 199 4805 BUTTON REC
5106 613 199 4850 DEC WINDOW,LEFT
5107 613 199 4867 DEC WINDOW,RIGHT
5108 613 199 7912 BUTTON TIMER
5112 613 121 7324 BADGE
6001 CABINET BOTTOM-HALF (N.S.P)
6002 FRAME FRONT-F2F02 (N.S.P)
6003 613 202 8929 COVER BACK-L8HAE
6004 613 199 4706 COVER FAN
6005 645 058 0406 STAND(V0)
6006 613 199 4720 HOLDER HDD-1
6007 613 199 4737 HOLDER HDD-2
6011 613 200 4268 SPACER
6012 613 096 4021 HOLDER
6013 613 200 7832 EARTH
6014 613 059 4099 SPRING PLATE
6015 613 059 4099 SPRING PLATE
6017 613 201 8319 SPACER
6030 645 002 1121 FIXER
6031 613 203 6870 EARTH LAN - L8HAE
6035 LABEL (With out HDD)
7001 645 057 2036 MOTOR,FAN DC 1.56W
CP-1 613 202 0671 COMPL PWB,CP-1-A MAC
DM-1 613 202 7946 COMPL PWB,DM-1
OP-1 613 203 5804 COMPL PWB,OP-1
PW-1 613 203 4685 COMPL PWB,PW-1
TB-1 613 203 5866 COMPL PWB,TB-1
HDD COMPL HDD (With out HDD)
NJ503 411 098 1303 SCR S-TPG BIN 3X6A
NJ601 411 184 5802 SCR S-TPG BIN+OTW 3X6
NJ602 411 184 5802 SCR S-TPG BIN+OTW 3X6
NJ603 411 002 0804 SCR BIN 4X6
NJ604 411 085 3709 WASHER OUT TW 4
NJ605 411 001 1901 SCR S-TPG BIN 3X6
NJ606 411 184 7400 SCR L-TPG PAN 3X10
NJ607 411 184 7400 SCR L-TPG PAN 3X10
NJ608 411 001 5206 SCR S-TPG PAN 4X20
NJ609 411 001 1901 SCR S-TPG BIN 3X6
NJ610 412 062 6102 SPECIAL SCREW-3.5X4.5
NJ611 411 001 1901 SCR S-TPG BIN 3X6
NJ612 411 001 1901 SCR S-TPG BIN 3X6
NJ613 411 001 1901 SCR S-TPG BIN 3X6
NJ614 411 001 1901 SCR S-TPG BIN 3X6
NJ616 411 001 1901 SCR S-TPG BIN 3X6
W0001 613 187 7887 ASSY,WIRE,CN501-INLET

10
LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION
ELECTRICAL PARTS
Note:
1. Materials of Capacitors and Resistors are abbreviated as follows ;
Resistors Capacitors
MT-FILM Metallized Film Resistor MT-POLYEST Metallized Polyester Capacitor
MT-GLAZE Metallized Glaze Resistor MT-COMPO Metallized Composite Capacitor
OXIDE-MT Oxide Metallized Film Resistor TA-SOLID Tantalum Solid Capacitor
AL-SOLID Aluminum Solid Capacitor
NP-ELECT Non-Polarized Electrolytic Capacitor
OS-SOLID Aluminum Solid Capacitors with Organic
Semiconductive Electrolytic Capacitor
DL-ELECT Double Layered Electrolytic Capacitor
2. Tolerance of Capacitor (10pF over) and Resistor are noted with follow symboles.
F ............1% G ............2% J ............5% K ............10%
M ..........20% N ..........30% Z ..........+80% ~ -20%
3. Capacitors
U : µF P : pF
4. Inductors
UH : µH MH : mH
5. N.S.P. : Not available as service parts.
COMPL PWB,CP-1-A MAC
613 202 0671
(BATTERY)
Z3300 645 008 5765 BATTERY,RECHARGE
(SEMICONDUCTORS)
Q1003 405 002 0308 TR 2SA1037K-R
Q1103 405 189 1907 TR 2SC4452-4-TL-E
Q1104 405 189 1907 TR 2SC4452-4-TL-E
Q1105 405 141 0603 TR 2SA1037AK-R
OR 405 002 0308 TR 2SA1037K-R
OR 405 002 0209 TR 2SA1037K-Q
OR 405 002 0407 TR 2SA1037K-S
Q1137 405 029 3504 TR DTC144EK
Q1173 405 014 4400 TR 2SC2412K-Q
OR 405 014 4509 TR 2SC2412K-R
OR 405 014 4608 TR 2SC2412K-S
Q3092 405 000 2007 TR DTA144EK
Q3200 405 014 4400 TR 2SC2412K-Q
OR 405 014 4509 TR 2SC2412K-R
OR 405 014 4608 TR 2SC2412K-S
Q3300 405 141 0603 TR 2SA1037AK-R
OR 405 002 0308 TR 2SA1037K-R
OR 405 002 0209 TR 2SA1037K-Q
OR 405 002 0407 TR 2SA1037K-S
Q3301 405 141 0603 TR 2SA1037AK-R
OR 405 002 0308 TR 2SA1037K-R
OR 405 002 0209 TR 2SA1037K-Q
OR 405 002 0407 TR 2SA1037K-S
Q3302 405 141 0603 TR 2SA1037AK-R
OR 405 002 0308 TR 2SA1037K-R
OR 405 002 0209 TR 2SA1037K-Q
OR 405 002 0407 TR 2SA1037K-S
Q3303 405 141 0603 TR 2SA1037AK-R
OR 405 002 0308 TR 2SA1037K-R
OR 405 002 0209 TR 2SA1037K-Q
OR 405 002 0407 TR 2SA1037K-S
Q3304 405 014 4400 TR 2SC2412K-Q
OR 405 014 4509 TR 2SC2412K-R
OR 405 014 4608 TR 2SC2412K-S
Q3305 405 014 4400 TR 2SC2412K-Q
OR 405 014 4509 TR 2SC2412K-R
OR 405 014 4608 TR 2SC2412K-S
Q3306 405 014 4400 TR 2SC2412K-Q
OR 405 014 4509 TR 2SC2412K-R
OR 405 014 4608 TR 2SC2412K-S
Q3307 405 014 4400 TR 2SC2412K-Q
OR 405 014 4509 TR 2SC2412K-R
OR 405 014 4608 TR 2SC2412K-S
Q3308 405 029 3504 TR DTC144EK
Q3309 405 141 0603 TR 2SA1037AK-R
OR 405 002 0308 TR 2SA1037K-R
OR 405 002 0209 TR 2SA1037K-Q
OR 405 002 0407 TR 2SA1037K-S
Q3401 405 089 2103 TR 2SC4483-S
Q3401 405 089 2202 TR 2SC4483-T
Q3403 405 000 5305 TR DTC143TK
OR 405 045 2208 TR 2SC3900
Q3404 405 141 0603 TR 2SA1037AK-R
OR 405 002 0308 TR 2SA1037K-R
OR 405 002 0209 TR 2SA1037K-Q
OR 405 002 0407 TR 2SA1037K-S
Q3405 405 029 3504 TR DTC144EK
Q3406 405 141 0603 TR 2SA1037AK-R
OR 405 002 0308 TR 2SA1037K-R
OR 405 002 0209 TR 2SA1037K-Q
OR 405 002 0407 TR 2SA1037K-S
Q3407 405 141 0603 TR 2SA1037AK-R
OR 405 002 0308 TR 2SA1037K-R
OR 405 002 0209 TR 2SA1037K-Q
OR 405 002 0407 TR 2SA1037K-S
Q3408 405 141 0603 TR 2SA1037AK-R
OR 405 002 0308 TR 2SA1037K-R
OR 405 002 0209 TR 2SA1037K-Q
OR 405 002 0407 TR 2SA1037K-S
Q3409 405 014 4400 TR 2SC2412K-Q
OR 405 014 4509 TR 2SC2412K-R
OR 405 014 4608 TR 2SC2412K-S
Q3441 405 141 0603 TR 2SA1037AK-R
OR 405 002 0308 TR 2SA1037K-R
OR 405 002 0209 TR 2SA1037K-Q
OR 405 002 0407 TR 2SA1037K-S
Q3470 405 014 4400 TR 2SC2412K-Q
OR 405 014 4509 TR 2SC2412K-R
OR 405 014 4608 TR 2SC2412K-S
Q3471 405 141 0603 TR 2SA1037AK-R
OR 405 002 0308 TR 2SA1037K-R
OR 405 002 0209 TR 2SA1037K-Q
OR 405 002 0407 TR 2SA1037K-S
(INTEGRATED CIRCUITS)
IC101 409 541 0003 IC SAA7115
IC102 409 541 0102 IC SAA7126H
IC103 409 541 0201 IC PCM1800
IC104 409 541 0300 IC AK4380VT
IC116 409 541 7408 IC PST598IN
IC117 409 228 9206 IC NJM2100M
IC118 409 581 3101 IC BD45295G
IC300 409 615 2308 IC V1.04 MPEG BIGDRV SUB
IC301 409 482 3002 IC BR24C08F
OR 409 504 7001 IC 24LC08BT/SN
IC303 409 353 4206 IC PST9127N
IC304 409 540 3906 IC MAX3100EEE
IC320 409 563 8605 IC RTL8139CL
IC321 409 540 4002 IC AT93C46I18
IC330 409 432 6404 IC MAX3082CSA
IC331 409 544 6606 IC SI-3012KS-TL
IC340 409 306 1009 IC MM1031XM
IC342 409 084 0409 IC LA6458M
IC343 410 439 6908 IC LC74782M-9841-TRM
IC344 409 587 7707 IC LA7152-E